fold seats Citroen C4 PICASSO 2016 2.G Owner's Manual

67
C4-Picasso-II_en_Chap02_ouvertures_ed01-2016
Reinitialising the motorised
tailgate
This operation is necessary where there is
no movement - after detection of an obstacle,
connecting  or   recharging   the   battery,   ...
F
 
O
pen   the   tailgate   manually,   if   necessary.
F
 
M
anually   close   the   tailgate   fully.
If the problem persists, contact a CITROËN
dealer
  or   a   qualified   workshop.
Precautions in use
In wintry conditions
In the event of an accumulation of snow
on  the   tailgate,   clear   the   snow   before  
c

ommanding   a   motorised   opening   of  
t

he   tailgate.
The
  formation   of   ice   can   block   the  
t

ailgate   and   prevent   its   opening:   wait  
u

ntil   the   ice   melts   with   the   heating   of  
t

he
 p
assenger
 c
ompartment.
When washing the vehicle
When washing the vehicle in an automatic   car   wash,   don't   forget   to  
l

ock   your   vehicle   to   avoid   the   risk   of  
u

nexpected
 ope
ning.
Back-up release
Unlocking
F Fold  back   the   rear   seats   to   gain   access   to  t
he   lock   from   inside   the   boot.
F

I
nsert a small screwdriver into hole A of the
lock
  to   unlock   the   tailgate.
F
 
M
ove   the   latch   to   the   left.
Locking after closing
If the fault persists after closing again, the boot will   remain   locked.
To
  manually   unlock   the   boot   in   the   event   of   a  
b

attery   or   central   locking   failure.
2
Access

76
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Passenger's seat backrest angle
F Pull  the   control   upwards   or   turn   the   knob   to  a
djust   the   backrest.
When
  the   backrest   is   at   the   desired   angle,  
r

elease   the   control.
Table position for the
passenger's seat backrest
This position, associated with the position of
the  rear   seats,   allows   you   to   carry   long   objects  
i

nside   the   vehicle.
When the backrest is at the desired angle, release   the   control   lever.   To   ensure   that   the  
b

ackrest   does   not   suddenly   fold   for wards  
a

nd   hurt   you,   restrain   it   with   your   back   or  
y

our   hand   while   operating   the   control.
Check that there is no object that could inter fere with the movement of the seat,
both
  above   and   below.
F

P

lace the head restraint in the low position,
raise
  the   armrest   and   fold   the   fixed   table  
o

nto   the   back   of   the   seat.
F
 
P

ull   the   control   fully   up   and   tip   the   backrest  
fo

rwards.
To
 
return   to   the   normal   position,   guide   the  
b

ackrest   backwards   until   it   locks.
Ease of use and comfort

81
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Heated seats control
F Use  the   adjustment   wheel   to   switch   on   and  s
elect   the   level   of   heating   required:
0 :
  Off.
1 :
  Low.
2 :
  Medium.
3 :
  High.
With
  the   engine   running,   the   front   seats   can   be  
h

eated
 s
eparately.
Before
 
operating
 
the
 
leg
 
rest,
 
ensure
 
t

hat
 
nothing
 
could
 
inter fere
 
with
 
its
 
m

ovement.Electric passenger seat
F Push   the   control   for wards   or   backwards   to  u
nfold   or   fold   away   the   leg   rest.
The movement stops when you release the
control.
Front armrest
Height adjustment
F Fully   lower   the   armrest.
F R aise it to the required position (low,
intermediate
  or   high).
F
 
O
nce   in   the   high   position,   lift   to   release   it  
a

nd   return   it   to   the   low   position.
Comfort system for the driver and front
passenger.
3
Ease of use and comfort

82
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Second-row seats
Forwards-backwards adjustment
F Raise the lever A, located at the front of
the   seat   cushion,   and   adjust   the   seat   to   the  
de

sired
 p
osition.
The
 
3
 
seats
 
in
 
the
 
2
nd row are independent of each other and are all the same width. Their backrests can be folded to vary the load space in the boot.
A.
 F

or wards
 
and
 
backwards   adjustment:   raise  
t

he
 
lever.
B.
 B

ackrest
 
angle
 
adjustment:   pull   the   strap  
a

nd
 
guide
 
the
 
seat   to   the   rear.
C.
 F

olding
 
the
 
seat:
  pull   the   strap   up   to  
r

elease
 t

he
 sea

t.
D.
 F

olding
 
the
 
seat
 
from   the   rear:   pull   the  
s

trap
 
then
 
push
 
the   seat   for ward.
Ease of use and comfort

83
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
F Pull the strap B  and   guide   the   seat   to   the  r
e a r.
The
  backrest   reclines   and   the   seat   base   pivots  
s

li g ht l y.
"Comfort" position
Returning the seat to the initial
position
F Pull the strap B   and   guide   the   seat   for ward.
Super vise any movements of seats
when made by children. To
  remove   it:
- m ove   the   head   restraint   to   the   high   position,
-
 
p
ress   lug   A   pulling   the   head   restraint  
u

pwards   at   the   same   time.
The rear head restraints can be removed and
have
  two   positions:
-  
h
igh,   position   for   use,
-  
l
ow,   stowed   position.
To   raise   a   head   restraint,   pull   it   upwards.
To   lower   it,   press   lug   A   then   the   head   restraint.
Rear head restraints
Never drive with the head restraints
removed;
  they   must   be   in   place   and  
c

orrectly
 adj
usted.
To
 
refit
 
it:
-
 
e

ngage
 
the
 
head
 
restraint
 
rods
 
in
 
the
 
a

pertures,
 
keeping
 
them
 
in
 
line
 
with
 
the
 
s

eat
 
backrest.
Relax head restraints
Depending on version, the sides can be folded t o   obtain   a   more   comfortable   position.
3
Ease of use and comfort

84
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Flat floor
Folding a seat
From the outside
F P ull firmly upwards on strap C , as indicated
by
  the   arrow,   to   release   the   seat;   keep  
p

ulling   until   the   seat   is   fully   folded.
 P

ush   the   seat   backrest   gently   for wards  
s

o   that   the   backrest   folds   onto   the   seat  
c

ushion.   The   assembly   lowers   onto   the  
f

l o o r. From the boot, when loading
for example
You can fold the second-row seats from the
boot,
  after   first   folding   the   third-row   seats.
F

P
ull on the strap D to release the seat in
question
  then   push   for wards   lightly   on   the  
b

ackrest.
 T

o   avoid   any   damage   to   the   mechanism,  
t

he strap D unclips if too much force is
applied.
  Simply   clip   it   in   place   again   for   the  
s

ystem   to   be   operational   again.
F
 
P

lace
 
the
 
seats
 
in
 
the
 
fully
 
back
 
position.
Each seat can be folded onto the floor to vary
the
 
space
 
available
 
in
 
the
 
boot.
Ease of use and comfort

85
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Repositioning a seat
Before operating the rear seats, check that the outer rear seat belts are not
loose,
  to   avoid   damaging   them.   The  
c

entre   belt   must   be   stowed.   Fix   the  
t

ongues   of   the   three   belts   to   their  
anc

horage
 p
oints.
Continuity panels
These continuity panels are not
designed  to   support   a   weight   greater  
t

han   30   kg. Releasing / locking the continuity panels
F
 
B
efore   unfolding   the   continuity   panels,  
c

heck   that   the   seats   in   the   2
nd row are fully
back.
F

S

lide the continuity panel latch upwards to
release.
F
 
S

traighten
 
the
 
continuity
 
panel,   then   slide  
t

he
 
latch
 
downwards
 
to
 
lock
 
it.
F
 
I

f
 
necessary,
 
straighten
 
the
 
continuity
 
p

anels for the seats in the 2
nd row and lock t
hem
 
in
 
place.
F
 
R

aise
 
the
 
backrest
 
and
 
push
  it   rear wards  
u

ntil
 
it
 
locks
 
in
 
position Each seat has a continuity panel at the bottom
of
  the   backrest,   that   once   unfolded:
- p rovides a continuous load sur face in the
boot, whatever the position of the seats,
-
 
a
voids   objects   sliding   under   the   seats   in  
t

he 2
nd row.
3
Ease of use and comfort

86
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Access to the third-row
seats
Access to the third-row seats is via the outer
second-row seats.
F

P
ull the lever E .
  The   seat   is   released   and  
t

he   seat   cushion   comes   up   against   the  
b

ackrest.
F

H
old the lever E in the raised position,
pushing
  for wards.   The   whole   seat   slides  
t

owards   the   front   seat.
Space becomes free behind the seat, the
third-row
  passengers   can   get   to   their   seats.
Leaving the vehicle from
the third-row seatsRepositioning a seat, from
the outside, with the door
open
In the event of a failure of this system
(lever E
),
  the   passengers   in   the   third  
r

ow can also leave the vehicle after first
folding
  the   backrests   of   the   second-row  
s

eats   using   the   strap   D.
Do not allow children to operate the
seats
 w

ithout
 s
upervision.
F

L

ift the lever E
.
 
The
 
seat
 
is
 
released
 
and
 
t

he
 
seat
 
cushion
 
comes
 
up
 
against
 
the
 
b

ackrest.
F
 
P

ush
 
the
 
seat
 
backrest,
 
still
 
holding
 
the
 l
ever E
 
in
 
the
 
raised
 
position. If
 
there   are   passengers   seated   in   the   third   row:
F

m

anually return the assembly as far
as   possible   rear wards;   the   seat   does  
n

ot   return   to   the   fully   back   position,   so  
a

s   to   retain   legroom   for   the   third-row  
p

assengers,
F
 
f

old   the   seat   cushion   until   it   locks.
Ensure   that   there   is   no   object   on   or   under   the  
s

eat
 
that   you   want   to   move.
Before
 
operating
 
the
 
seats,
 
ensure
 
that
 
t

he
 
tables
 
on
 
the
 
back
 
of
 
the
 
first-row
 
s

eats
 
are
 
folded
 
away.
Ease of use and comfort

87
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
Third-row seats
Concertina boards
Folding the concertina boardsF Remove  the   luggage   net.  F
or   more   information   on   the   luggage   net  
a

nd the Interior fittings , refer to the
corresponding
 s

ection.
F

R
eturn the second-row continuity panels to
their
  initial   position   and   lock   them   in   place.
F

F
old the concertina boards and position
them
 v

ertically.
F

P
ull on the strap F located behind the seat
backrest.
  The   backrest   pivots   rear wards,  
p

ulling   the   seat   base   with   it.   The   seat   locks  
i

n   the   open   position.
Each of the two floor panels can
support
 
a
 
load
 
of
 
100
 
kg.
Pull
 
on
 
the
 
control,
 
the
 
3
 
sections
 
of
 
the
 
board
 
w

ill
 
fold
 
like
 
a
 
concertina.
When
 
the
 
third-row
 
seats
 
are
 
upright,
 
these
 
c

oncertina
 
boards
 
can
 
be
 
left
 
either:
-
f

lat behind the seats,
-

i

n the vertical position,
thereby
 
leaving
 
a
 
storage
 
area
 
available.
Repositioning the
seats
Two rigid concertina boards, which cannot b e separated from the vehicle, cover the
2
third-row seats, when these are in the folded
position.
3
Ease of use and comfort

88
C4-Picasso-II_en_Chap03_ergonomie-confort_ed01-2016
F Return the second-row continuity panels to their   initial   position   and   lock   them.
F
 
L
ower   the   head   restraints.
F

C
orrectly position the concertina board
vertically
  behind   the   seat.
F
 
C
heck   that   the   seat   belts   for   the   3
rd row
seats
 
are
 
correctly
 
fixed
 
to
 
the
 
loops   and  
a

re
 
not
 
folded.
F

P

ull the strap G , located at the bottom of
the
 
seat
 
backrest.
 
The
 
seat
 
unlocks. Before
  moving   the   third-row   seats,  
r

eturn   the   rigid   floor   plates   of   the  
s

econd-row   seats   to   the   upright   position  
a

nd   lock   them   in   place.
Do not try to fold a third-row seat that
has   not   first   had   the   backrest   fully  
l

ocked   in   place.
Do
  not   leave   objects   either   on   or  
u

nderneath the seat bases of the third-
row
  seats   when   you   are   folding   them.
Do not leave your hand on the control
G
as
  you   fold   the   seats,   as   you   risk  
t

rapping
 y
our
 f
ingers.
Do not allow children to operate the
seats
 w

ithout
 s
upervision.
F
 
N
ext   push   the   backrest   gently   for wards.  
T

he   backrest   pivots,   folding   onto   the   seat  
b

ase.   The   seat   base   then   folds   into   the  
s

towage   area   provided   for   that   purpose.
F
R
eposition the concertina boards over the
folded   seats.
Folding the seats
Ease of use and comfort