wheel Citroen C4 PICASSO RHD 2012 1.G User Guide

III
68
COMFORT
FRONT SEATS

1. Adjustment of the
seat height and angle,
forwards-backwards
2. Adjustment of backrest
angle and lumbar support
The seats can also be adjusted elec-
trically for a short period:


- on opening one of the front
doors,

- after switching off the ignition.










Heated seats control
ELECTRIC ADJUSTMENTS

Raise or lower the front of
control to raise or lower the
front of the seat base (on
driver’s seat).
Raise or lower the rear of
control to raise or lower the
seat.
Action control forwards or
backwards to slide the seat
forwards/backwards. Push the top of control
forwards or backwards to
adjust the backrest angle.
Raise or lower control to
increase or decrease the
lumbar support.

With the engine running, the front
seats can be heated individually.


)
Use the corresponding adjust-
ment wheel, placed on the inner
side of each front seat, to switch
on and select the level of heating
required:

0
: Off.

1
: Low.

2
: Medium.

3
: High.

III
77
COMFORT





Rear view mirror

Adjustable mirror providing a central
rearward view.
Equipped with an anti-dazzle sys-
tem, which darkens the mirror glass:
this reduces the nuisance to the
driver caused by the headlamps
from following vehicles, low sun...


Manual day/night model

Adjustment


)
Adjust the mirror so that the
glass is directed correctly in the
"day" position.


Day/night position


)
Pull the lever to change to the
"night" anti-dazzle position.

)
Push the lever to change to the
normal "day" position.

By means of a sensor, which mea-
sures the light from the rear of the
vehicle, this system automatically
and progressively changes between
the day and night uses.
STEERING WHEEL ADJUSTMENT
The height and reach of the steer-
ing wheel can be adjusted to adapt
the driving position to the size of the
driver.

Adjustment



)
First, adjust the driver's seat to
the most suitable position.

)


When stationary
, pull the control
lever to unlock the steering wheel
adjustment.

)
Adjust for height and reach.

)
Push the control lever to lock the
steering wheel adjustment.
After locking, if you press fi rmly on
the steering wheel, a slight click may
be heard.

As a safety measure, the mirrors
should be adjusted to reduce the
"blind spot".







Automatic day/night model
As a safety precaution, these
operations must only be carried out
while the vehicle is stationary.
In order to ensure optimum visibility
during your manoeuvres, the mirror
lightens automatically when reverse
gear is engaged.

IV
81
ACCESS
STARTING

1. "S": Steering lock

To unlock the steering, gently move
the steering wheel while turning the
key, without forcing it.


2. "M": Ignition on

Depending on the version of your
vehicle, the orange and red warn-
ing lamps should also come on for
a short time.


3. "D": Starter

Release the key as soon the engine
has started.
If the fi rst attempt fails, switch off the
ignition. Wait ten seconds then ope-
rate the starter again.


Steering lock


1. "

S":
After removing the key, turn
the steering wheel to lock the
steering. The key can only be
removed in position S
.

2. "M":
Ignition switched on, the
steering is unlocked (by turning
the key to position M
, move
the steering wheel gently if
necessary).

3. "D":
Starter position.


Key left in position "M"
audible warning
If you forget to remove the key from
the ignition, the ignition is switched
off automatically after one hour.
To switch the ignition back on, turn
the key to position S
then back to
position M
.

Do not run the engine in an en-
closed space or where there is
insuffi cient ventilation
.

You must always to keep the
engine running when moving in
order to retain braking and steer-
ing power assistance .

Never remove the ignition key
before the vehicle has come to a
complete stop.



Vehicles equipped with a
turbocharger
Never stop the engine without having
allowed it to run for a few seconds at
idle, this being the time required for
the turbocharger to return to a normal
speed.
Flicking the accelerator at the mo-
ment of switching off the ignition
could cause serious damage.

A heavy object (key fob...), attached
to the key and weighing down on
its shaft in the ignition switch, could
cause a malfunction. Never turn the key to this position
when the engine is running.

V
104
VISIBILITY
LIGHTING PACK

Interior mood lighting

This function activates the light
sources which are located in the
dashboard, near the interior door le-
vers and in the roof.
Operation
This back-lit control, located near
the steering wheel below the dash-
board, is used to switch on and off
and adjust the brightness of this
lighting.
To increase
brightness:


)
Press the right of the control to
obtain the desired level.
To reduce
brightness:


)
Press the left of the control to
obtain the desired level.
The setting is stored when the ignition
is switched off.


Interior welcome lighting

When unlocking the vehicle with the
remote control or the key, the foot-
well lamps, interior lamps and interior
mood lighting sources come on for
30 seconds.
This function cannot be deactivated.


Front door pockets with
automatic lighting

The lighting for the door pockets
comes on automatically when you
place a hand inside one of the com-
partments.
It goes off after a few seconds when
you take your hand away.

Reading lamps on front seat
backrests

There are reading lamps in the back-
rests of the front seats, behind the
rear tables. They can operate only
when the table is lowered.


)
Press the "On/Off" button to switch
the reading lamp on or off. This lighting, available once the
sidelamps are on, in night mode,
provides subdued lighting in the
passenger compartment.

VI
116
FITTINGS
TORCH

This is a portable lamp, fi tted in the
boot wall, which can be used to illu-
minate the boot or as a torch.

Grand C4 Picasso


C4 Picasso

Boot lamp
The boot lamp A
comes on automat-
ically when the boot is opened and
switches off automatically when the
boot is closed.
Various lighting durations are avail-
able:


- ignition off, approximately ten minutes,


- in energy economy mode, approxi-
mately thirty seconds,

- engine running, no limit.


Operation of the torch
This torch operates with NiMH re-
chargeable batteries.
It has a battery life of approximately
45 minutes and recharges while you
are driving.

)
Extract the torch from its location
pulling it upwards, as indicated
by the arrow.

)
Press the switch B
, located on
the back, to switch the torch on
or off.

)
Unfold the support C
, located on
the back, to set down and raise
the torch; for example, when
changing a wheel.


Stowing the torch


)
Put the torch back in place in its
location, starting at the bottom.
If you have forgotten to switch off
the torch, this switches it off auto-
matically. Observe the polarities when fi tting
the batteries.
Never replace the rechargeable
batteries with normal single-use
batteries.
For replacement of the batteries,
see the "Practical information -
Changing a bulb" section.
It the torch is not engaged correctly,
it may not charge and may not come
on when the boot is opened.

Using the torch

VIII
126
SAFETY
DIRECTION INDICATORS


)
Left: lower the lighting stalk
beyond the point of resistance.

)
Right: raise the lighting stalk
beyond the point of resistance.
HAZARD WARNING LAMPS

A visual warning by means of the
direction indicators to alert other
road users to a vehicle breakdown,
towing or accident.












Automatic operation of
hazard warning lamps
When braking in an emergency,
depending on the deceleration, the
hazard warning lamps come on
automatically.
They switch off automatically the
fi rst time you accelerate.


)
You can also switch them off by
pressing the button.








Horn

Audible warning system to alert other
road users to an imminent danger. Selection of the left or right direc-
tion indicators to signal a change of
direction of the vehicle.


)
Press this button, the direction
indicators fl ash.
They can operate with the ignition
off.

)
Press at the lower part of the
fi xed centred controls steering
wheel.
Use the horn moderately and only
in the following circumstances:


- immediate danger,

- approaching a location lacking
visibility.







"Motorway" function



)
Press briefl y upwards or down-
wards, without going beyond the
point of resistance; the direction
indicators will fl ash 3 times.

VIII
127
SAFETY
TYRE UNDER-INFLATION DETECTION
Sensors fi tted in each valve check
the tyre pressure during driving and
trigger a warning in the event of
malfunction (speed above 12 mph
(20 km/h)).

Under-infl ated tyre The tyre under-infl ation detection
system is an aid to driving which
does not replace the vigilance or
responsibility of the driver.
Puncture
The service warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen lo-
cating the wheel concerned.
Check the tyre pressures as soon as
possible. This check must be carried
out when the tyres are cold. The STOP
warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen lo-
cating the wheel concerned.
Stop immediately, avoiding any sud-
den movement of the steering wheel
and the brakes.
Change the damaged wheel (punc-
tured or very defl ated tyre), and
have the tyre pressure checked as
soon as possible.

Sensor(s) not detected or faulty
The service warning lamp
comes on in the instrument
panel, accompanied by an
audible signal and a mes-
sage on the multifunction screen
locating the wheel or wheels which
are not detected or indicating a fault
in the system.
Have the faulty sensor(s) checked
by a CITROËN dealer or a qualifi ed
workshop. All repairs and changing of tyres
on a wheel fi tted with this system
must be carried out by a CITROËN
dealer or a qualifi ed workshop.
If, when changing a tyre, you in-
stall a wheel which is not detected
by your vehicle (example: fi tting
of snow tyres), you must have the
system reinitialised by a CITROËN
dealer or a qualifi ed workshop.

This system does not avoid the need to have the tyre pressures checked
regularly (refer to the "Technical
data - Identifi cation markings" sec-
tion) to ensure that the optimum
dynamic performance of the vehicle
is maintained and prevent prema-
ture wear of the tyres, particularly in
arduous driving conditions (heavy
load, high speed).
The tyre pressures must be
checked cold, at least once a
month. Remember to check the
pressure of the spare wheel.
The tyre under-infl ation detection
system may experience temporary
interference due to electro-magnetic
signals on a frequency close to that
used by the system.
This message is also displayed
when one of the wheels is away
from the vehicle (being repaired) or
when one or more wheels without a
sensor are fi tted.
The spare wheel is not fi tted with a
sensor.

VIII
128
SAFETY
BRAKING ASSISTANCE
SYSTEMS
Group of supplementary systems
which help you to obtain optimum
braking in complete safety in emer-
gency situations:


- anti-lock braking system (ABS),

- electronic brake force distribu-
tion (EBFD),

- emergency braking assistance
(EBA).


Anti-lock braking system
and electronic brake force
distribution
Linked systems which improve the
stability and manoeuvrability of your
vehicle when braking, in particular
on poor or slippery surfaces.

Activation
The anti-lock braking system comes
into operation automatically when
there is a risk of wheel lock.
Normal operation of the ABS may
make itself felt by slight vibration of
the brake pedal.
Operating fault

When braking in an emergency,
press very fi rmly without releasing
the pressure. If this warning lamp comes
on, accompanied by an au-
dible signal and a message
in the screen, it indicates a
malfunction of the anti-lock braking
system which could result in loss of
control of the vehicle when braking.
If this warning lamp comes
on, together with the STOP

and ABS
warning lamps,
accompanied by an audible
signal and a message in the screen,
it indicates a malfunction of the elec-
tronic brake force distribution which
could result in loss of control of the
vehicle when braking.

You must stop as soon as it is
safe to do so.

In either case, contact a CITROËN
dealer or a qualifi ed workshop.

When replacing wheels (tyres and
rims), ensure that they conform to
the manufacturer's recommenda-
tions.











Emergency braking assistance

System which, in an emergency,
enables you to obtain the optimum
braking pressure more quickly, thus
reducing the stopping distance.

Activation
It is triggered by the speed at which
the brake pedal is pressed.
The effect of this is a reduction in
the resistance of the pedal and an
increase in braking effi ciency.
When braking in an emergency,
press fi rmly without releasing the
pressure.

VIII
129
SAFETY
TRAJECTORY CONTROL
SYSTEMS

Anti-slip regulation (ASR)
and electronic stability
programme (ESP)

The anti-slip regulation (also known
as Traction Control) optimises trac-
tion to prevent skidding of the wheels,
by acting on the brakes of the driving
wheels and on the engine.
The electronic stability programme acts
on the brake of one or more wheels
and on the engine to keep the vehicle
on the trajectory required by the driver,
within the limits of the laws of physics.

Deactivation
In exceptional conditions (starting a
vehicle which is bogged down, stuck
in snow, on soft ground...), it may be
advisable to deactivate the ASR and
ESP systems, so that the wheels
can move freely and regain grip.


)
Press the "ESP OFF"
button, lo-
cated in the centre of the dash-
board.
If this warning lamp comes
on in the instrument panel
and the indicator lamp on the
button comes on, this indi-
cates that the ASR and ESP
systems are deactivated. This is indicated by fl ashing
of this warning lamp in the
instrument panel.

Activation
These systems are activated auto-
matically each time the vehicle is
started.
They come into operation in the event
of a grip or trajectory problem.

Intelligent Traction Control
system *

Your vehicle has a system to help
driving on snow.
This automatic system continuously
checks for situations of diffi cult sur-
face adhesion that could make it dif-
fi cult to move off or make progress
on deep fresh snow or compacted
snow.
In these situations, the system takes
over from the ASR
system by opti-
mising the amount of wheel slip to
provide the best traction and trajec-
tory control, even without snow tyres
and with or without chains.
In extremely severe conditions (snow on top of ice, sand, deep mud…), it
can be useful to deactivate the ESP/
ASR
systems to allow a degree of
wheel spin and so recover grip.

*
Depending on engine type.

VIII
130
SAFETY

Reactivation
These systems are reactivated au-
tomatically each time the ignition is
switched back on or from 30 mph
(50 km/h).


)

Press the "ESP OFF"
button again
to reactivate them manually.



Operating fault
If this warning lamp comes
on, accompanied by an au-
dible signal and a message
in the multifunction screen,
this indicates a malfunction of these
systems.
Have it checked by a CITROËN
dealer or a qualifi ed workshop. The ESP/ASR systems offer ex-
ceptional safety in normal driving,
but this should not encourage the
driver to take extra risks or drive at
high speed.
The correct operation of these sys-
tems depends on observation of
the manufacturer's recommenda-
tions regarding wheels (tyres and
rims), braking components, elec-
tronic components and assembly
and repair procedures.
After an impact, have these systems
checked by a CITROËN dealer or a
qualifi ed workshop.

EMERGENCY OR
ASSISTANCE CALL
This system allows you to make an
emergency or assistance call to the
emergency services or to the dedi-
cated CITROËN service.
For more information on the use of
this function, refer to the "Audio and
telematics" section.