bulb Citroen DS3 2011 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2011, Model line: DS3, Model: Citroen DS3 2011 1.GPages: 324, PDF Size: 25.11 MB
Page 7 of 324
CHECKS PRACTICAL
INFORMATIONTECHNICAL
DATAAUDIO AND
TELEMATICS
179 Bonnet
180 Running out of fuel (Diesel)
181 Petrol engines
182 Diesel engines
183 Checking levels
186 Checks190 Temporary puncture
repair kit
196 Changing a wheel
203 Changing a bulb
210 Changing a fuse
217 Battery
219 Energy economy mode
220 Changing a wiper blade
221 Towing the vehicle
223 Towing a trailer
225 Accessories230 Petrol engines
232 Petrol weights
234 LPG engines
235 LPG weights
236 Diesel engines
237 Diesel weights
238 Dimensions
240 Identifi cation markings245 Emergency or assistance
247 MyWay
281 Audio system
012012013013010010011011
Page 127 of 324
125Fittings
To remove the shelf:
)
unhook the two cords,
)
raise the shelf slightly, then unclip it on
each side.
Rear parcel shelf
)
Raise the boot carpet by pulling the strap
upwards to gain access to the storage box.
This has areas for storing a temporary puncture
repair kit, a box of spare bulbs, a first aid kit,
two warning triangles, ...
Storage box
)
refit the boot floor carpet by folding it
slightly in the middle.
Page 190 of 324
011
Practical information
This section describes the use of the temporary puncture repair kit,
the procedures for changing a punctured wheel, a worn wiper blade and
the various bulbs and fuses, as well as advice on charging the battery
and towing the vehicle and information on the range of accessories
available from the dealer network.
Page 205 of 324
203Practical information
Changing a bulb
The headlamps are fitted with
polycarbonate glass with a protective
coating:
)
do not clean them using a dr y
or abrasive cloth, nor with a
detergent or solvent product,
)
use a sponge and soapy water,
)
when using a high pressure washer
on persistent marks, do not direct
at the lamps or their outlines for
too long, so as not to damage their
protective coating and seals.
)
Do not touch the bulb directly with
your fingers, use lint-free cloths.
Changing a bulb should only be done
after the headlamp has been switched
off for a few minutes (risk of serious
burns).
It is imperative to use only anti-
ultraviolet (UV) type bulbs in order not
to damage the headlamp.
Always replace a failed bulb with a
new bulb with the same type and
specification.
Front lamps
1.
Direction indicators (PY21W amber).
2.
Sidelamps (W5W).
3.
Main beam headlamps (H1-55W).
4.
Dipped beam headlamps (H7-55W).
5.
Front foglamps (PSX24W).
6.
LED lamps (
LEDs
).
Page 206 of 324
Changing direction indicator
bulbs
When refitting, close the protective
cover carefully to preser ve the sealing
of the headlamp.
Amber coloured bulbs, such as the
direction indicators, must be replaced
with bulbs of identical specifications
and colour. Rapid flashing of the direction indicator
warning lamp (right or left) indicates the
failure of a bulb on that side.
)
Turn the bulb holder a quar ter of a turn and
extract it.
)
Pull out the bulb and change it.
To refit, carry out these operations in reverse
order.
Changing dipped beam headlamp
bulbs
)
Remove the protective cover by pulling on
the tab.
)
Disconnect the bulb connector.
)
Spread the springs to release the bulb.
)
Extract the bulb and change it.
To refit, carry out these operations in reverse
order.
Page 207 of 324
205Practical information
Changing main beam headlamp
bulbs
)
Remove the protective cover by pulling on
the tab.
)
Disconnect the bulb connector.
)
Spread the springs to release the bulb.
)
Remove the bulb and change it.
To refit, carry out these operations in reverse
order.
Changing sidelamp bulbs
)
Remove the protective cover by pulling on
the tab.
)
Pull the bulb holder pressing on the tabs on
both sides.
)
Pull the bulb and change it.
To refit, carry out these operations in reverse
order.
Changing integrated direction
indicator side repeaters
)
Insert a screwdriver towards the centre of
the repeater between the repeater and the
base of the door mirror.
)
Tilt the screwdriver to extract the repeater
and remove it.
)
Disconnect the repeater connector.
)
Replace the module.
To refit, carry out these operations in reverse order.
Contact a CITROËN dealer or
a qualified workshop to obtain a
replacement side repeater module.
Page 208 of 324
To obtain a replacement module,
contact your CITROËN dealer or a
qualified workshop.
If you experience any difficulty in
replacing bulbs, contact your CITROËN
dealer or a qualified workshop.
Changing front foglamp bulbs
)
Access to the front foglamp is through the
aper ture below the bumper.
)
Disconnect the black bulb holder
connector, by pressing on the tab at
the top.
)
Remove the bulb-holber by pressing on the
2 clips (at the top and the bottom).
)
Replace the module.
To refit, carry out these operations in reverse
order.
Changing the LED lamps
For the replacement of this type of LED lamp,
contact a CITROËN dealer or a qualified
workshop.
Page 209 of 324
207Practical information
1.
Brake lamps/sidelamps (P21/5W).
2.
Sidelamps (P5W).
3.
Direction indicators (PY21W amber)
4.
Foglamp,
offside
(PR21W red)
Reversing lamp,
nearside
(P21W).
Rear lamps
Amber or red bulbs, such as those
for the direction indicators and rear
foglamp, must be replaced by bulbs of
the same rating and colour.
Changing bulbs
)
Open the boot.
)
Remove the access flap from the
corresponding side trim panel.
)
Unscrew the butter fly nut securing the
lamp unit.
)
Unclip the lamp unit connector.
)
Extract the lamp unit carefully pulling in its
middle towards the outside.
)
Spread the four tabs and remove the bulb
holder.
)
Turn the bulb a quar ter of a turn and
change it.
To refit, carry out these operations in reverse
order.
Take care to engage the lamp unit in its guides,
while keeping it in line with the vehicle.
Page 210 of 324
Changing the number plate lamp
bulbs (W5W)
)
Inser t a thin screwdriver into one of the
outer holes of the lens.
)
Push it outwards to unclip.
)
Remove the lens.
)
Pull the bulb out and change it.
Third brake lamp (4 W5W bulbs)
)
Open the boot.
)
Remove the plugs A
on the inner panel.
)
Push on the centre of the lamp using
two screwdrivers to lever it outwards.
)
Disconnect the connector and if necessary
the screenwash pipe from the lamp.
)
Turn the bulb holder for the faulty bulb a
quar ter of a turn.
)
Pull out the bulb and change it.
To refit, carry out these operations in reverse
order.
Third brake lamp (LEDs)
For the replacement of this type of LED lamp,
contact a CITROËN dealer or a qualified
workshop.
Page 211 of 324
209Practical information
Interior lighting
Interior lamp (1/W5W)
Detach the cover of the interior lamp 1
with a
thin screwdriver, close to the button, to access
the faulty bulb.
Map reading lamps (2/W5W)
Detach the cover of the interior lamp 1
. To
access the faulty bulb, detach the par tition for
the reading lamp 2
concerned.
Boot lamp (W5W)
Detach the unit by pushing it rear wards.
Footwell and central storage
lamps (W5W)
Detach the unit for access to the bulb.
Glove box lamp (W5W)
Detach the unit for access to the bulb.