light Citroen DS3 2015 1.G Owner's Guide

DS3_en_Chap04_conduite_ed01-2015
A few driving recommendations
Observe the driving regulations at all times and remain vigilant whatever the traffic conditions.
P ay   close   attention   to   the   traffic   and   keep   your   hands   on   the   wheel   so   that   you   are   ready   to   react   at  
a

ny   time   to   any   eventuality.
On
  a   long   journey,   a   break   every   two   hours   is   strongly   recommended.
In
  difficult   weather,   drive   smoothly,   anticipate   the   need   to   brake   and   increase   the   distance   from  
o

ther
 v
ehicles.
driving on flooded roads
We strongly advise against driving on flooded roads,   as   this   could   cause   serious   damage  
t

o   the   engine   or   gearbox,   as   well   as   to   the  
e

lectrical   systems   of   your   vehicle.
Important!
Never drive with the parking brake applied   -   Risk   of   overheating   and  
d

amage   to   the   braking   system!
Do
  not   park   or   run   the   engine   when  
s

tationary   in   areas   where   inflammable  
s

ubstances   and   materials   (dry   grass,  
d

ead   leaves...)   might   come   into   contact  
w

ith   the   hot   exhaust   system   -   Risk   of  
f

ire!
Never leave a vehicle unsupervised
with
  the   engine   running.   If   you   have  
t

o   leave   your   vehicle   with   the   engine  
r

unning,   apply   the   parking   brake  
a

nd   put   the   gearbox   into   neutral   or  
p

osition

n or P,
  depending   on   the   type  
o

f   gearbox.
-
 
c

heck
 
that
 
the
 
depth
 
of
 
water
 
does
 
not
 
e

xceed
 
15
 
cm,
 
taking
 
account
 
of
 
waves
 
t

hat
 
might
 
be
 
generated
 
by
 
other
 
users,
-
 
d

eactivate
 
the
 
Stop
 
&
 
Start
 
system,
-

d

rive as slowly as possible without
stalling.
 
In
 
all
 
cases,
 
do
 
not
 
exceed
 
6
 
mph
 
(

10 km/h),
-

d

o not stop and do not switch off the
engine.
If
 
you
 
are
 
obliged
 
to
 
drive
 
through
 
water: On
 
leaving
 
the
 
flooded
 
road,
 
as
 
soon
 
as
 
c

ircumstances
 
allow,
 
make
 
several
 
light
 
brake
 
a

pplications
 
to
 
dry
 
the
 
brake
 
discs
 
and
 
pads.
If in doubt on the state of your vehicle, contact
a
 
CITROËN
 
dealer
 
or
 
a
 
qualified
 
workshop.

DS3_en_Chap04_conduite_ed01-2015
There is a risk of damage to the gearbox:
- i f you press the accelerator and
brake
  pedals   at   the   same   time,
-
 
i
f   you   force   the   movement   of   the  
s

elector   from   the   P position to
another position when the battery
is
  flat.
To
  reduce   fuel   consumption   when   at
 a

  prolonged   standstill   with   the   engine
 r

unning   (traffic   jam...),   put   the   selector   in
 t

he
n  

position   and   apply   the   parking   brake.
If the selector is not in position P
,
when
 
the
 
driver's
 
door
 
is
 
opened
 
or
 
a

pproximately
 
45
 
seconds
 
after
 
the
 
i

gnition
 
is
 
switched
 
off,
 
a
 
warning
 
m

essage
 
appears
 
in
 
the
 
screen.
F

R

eturn the selector to position P ;
 
t

he
 
message
 
disappears.
When
 
driving
 
on
 
flooded
 
roads
 
or
 
when
 
c

rossing
 
a
 
ford,
 
proceed
 
at
 
walking
 
p

ace.
Operating fault
Manual operation
When the ignition is on, the lighting o
f   this   warning   lamp,   accompanied  
b

y
 
an
 
audible   signal   and   a   message   in   the  
m

ultifunction   screen,   indicates   a   gearbox   fault.
In
 
this
 
case,   the   gearbox   switches   to   back-up  
m

ode
 
and
 
is   locked   in   3rd   gear.   You   may   feel  
a

 
substantial   knock   when   changing   from   P
to R
 
and
 
from  n to R .
  This   will   not   cause   any  
d

amage
 
to
 
the   gearbox.
Do
 
not
 
exceed   60   mph   (100   km/h),   local   speed  
r

estrictions
 p
ermitting.
Contact
 
a
 
CITROËN   dealer   or   a   qualified  
w

orkshop
 
as   soon   as   possible.
F
Sel
ect position M for sequential c
hanging o
f
 
the
 
four
 
gears.
F

P

ush the selector towards the +
 
sign
 
to
 
c

hange
 
up
 
a
 
gear.
F

P

ull the selector towards the -
 
sign
 
to
 
c

hange
 
down
 
a
 
gear.
It
 
is
 
only
 
possible
 
to
 
change
 
from
 
one
 
gear
 
to
 
a

nother
 
if
 
the
 
vehicle
 
speed
 
and
 
engine
 
speed
 
p

ermit;
 
other wise,
 
the
 
gearbox
 
will
 
operate
 
t

emporarily
 
in
 
automatic
 
mode. This
 
symbol
 
is
 
displayed
 
if
 
a
 
gear
 
i

s
 
not
 
engaged
 
correctly
 
(selector
 
b

etween
 
two
 
positions).
d

 
disappears
 
and
 
the
 
gears
 
e

ngaged
 
appear
 
in
 
succession
 
in
 
the
 
in

strument
 pan

el.
Stopping the vehicle
Before switching off the engine, you can engage p osition P or
n 
to   place   the   gearbox   in   neutral.
In
  both   cases,   apply   the   parking   brake   to  
i

mmobilise   the   vehicle.
Invalid value during manual
operation
If the engine speed is too low or too high, the gear   selected   flashes   for   a   few   seconds,   then  
t

he   actual   gear   engaged   is   displayed.
It
  is   possible   to   change   from   position  d
(automatic)
  to   position   M   (manual)   at   any   time.
When
  the   vehicle   is   stationary   or   moving  
v

ery   slowly,   the   gearbox   selects   gear   M1
automatically.
The
  sport   and   snow   programmes   do   not  
o

perate   in   manual   mode.

DS3_en_Chap04_conduite_ed01-2015
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "ECO" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
y

ou
 
press
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
s

elector in position
n
.
A

 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 
during
 a

 
journey.
 
It
 
rests
 
itself
 
to
 
zero
 
every
 t

ime
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t

he
 
key. STOP
  mode   is   not   invoked   when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "ECO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

DS3_en_Chap05_visibilite_ed01-2015
Lighting controlsSystem for selection and control of the various front and rear lamps providing the vehicle's lighting.
T he   various   front   and   rear   lamps   of   the   vehicle  
a

re   designed   to   adapt   the   driver's   visibility  
p

rogressively   according   to   climatic   conditions:
-
 
s
idelamps,   to   be   seen,
-
 
d
ipped   beam   headlamps   to   see   without  
d

azzling
 o
ther
 d
rivers,
-
 
m
ain   beam   headlamps   to   see   clearly   when  
t

he   road   is   clear.
Main lighting
Other lamps are installed to fulfil the requirements   of   particular   conditions   of  
v

isibility:
-
 
a
  rear   foglamp   to   be   seen   from   afar,
-
 
f
ront   foglamps   for   improved   vision,
-
 
L
ED   lamps   to   be   seen   during   the   daytime.
Additional lighting
Various automatic lighting control modes are   also   available   according   to   the   following  
op

tions:
-
 
g
uide-me-home   lighting,
-
 
a
utomatic   illumination   of   headlamps.
Programming
In some weather conditions (e.g. low temperature   or   humidity),   the   presence  
o

f   misting   on   the   internal   sur face   of   the  
g

lass   of   the   headlamps   and   rear   lamps  
i

s   normal;   it   disappears   after   the   lamps  
h

ave   been   on   for   a   few   minutes.

131
DS3_en_Chap05_visibilite_ed01-2015
Model without AUTO lighting
Model with AUTO lighting
Manual controls
The lighting is controlled directly by the driver by   means   of   the   ring   A   and   the   stalk   B.
Automatic
  illumination   of   headlamps.
B.
 S

talk   for   switching   the   headlamp   beam:  
p

ull   the   stalk   to   switch   between   dipped   and  
m

ain   beam   headlamps.
In
  the   lamps   off   and   sidelamps   modes,  
t

he   driver   can   switch   on   the   main   beam  
h

eadlamps   temporarily   ("headlamp   flash")   by  
m

aintaining   a   pull   on   the   stalk.
A.
 M

ain   lighting   mode   selection   ring:   turn   it  
t

o   position   the   symbol   required   facing   the  
ma

rk.Lighting
  off   /   daytime   running   lamps.
Sidelamps
 o

nly.
Dipped headlamps or main beam headlamps.
displays
Lighting of the corresponding indicator lamp on the   instrument   panel   confirms   the   switching   on  
o

f   the   lighting   selected.
The
  instrument   panel   has   permanent   back-
lighting.
  Illumination   of   the   instrument   panel   is  
t

herefore   not   linked   to   the   exterior   lighting.
Visibility

DS3_en_Chap05_visibilite_ed01-2015
C. Foglamp  selection   ring.
The   foglamps   operate   with   the   dipped   and   main  
b

eam
 h
eadlamps.
Rotate
  and   release   the   ring   C:
F
 
f
or wards   a   first   time   to   switch   on   the   front  
fo

glamps,
F
 
f
or wards   a   second   time   to   switch   on   the  
r

ear
 fo
glamp,
F
 
r
ear wards   a   first   time   to   switch   off   the   rear  
fo

glamp,
F
 
r
ear wards   a   second   time   to   switch   of   the  
f

ront   fog   lamps.
Model with front foglamps
and a rear foglamp Lighting on audible warning
When the ignition is switched off, all o
f   the   lamps   switch   off   automatically,  
u

nless   guide-me-home   lighting   is  
a

ctivated.
If
  the   lighting   is   switched   on   manually  
a

fter   switching   off   the   ignition,   there  
i

s   an   audible   signal   when   a   front   door  
i

s opened to warn the driver that
they
  have   forgotten   to   switch   off   the  
v

ehicle's   lighting,   with   the   ignition   off.
In
  good   or   rainy   weather,   by   both   day  
a

nd   night,   the   front   foglamps   and   the  
r

ear   foglamp   are   prohibited.   In   these  
s

ituations,   the   power   of   their   beams  
m

ay   dazzle   other   drivers.
Do   not   forget   to   switch   off   the   front  
f

oglamps   and   the   rear   foglamp   when  
t

hey   are   no   longer   necessary.
Front
 
and
 
rear
 
foglamps
When
 
the
 
lighting
 
is
 
switched
 
off
 
automatically
 
(

with
 
AUTO
 
model)
 
or
 
when
 
the
 
dipped
 
h

eadlamps
 
are
 
switched
 
off
 
manually,
 
the
 
f

oglamps
 
and
 
sidelamps
 
will
 
remain
 
on.
F
 
T

urn
 
the
 
ring
 
rear wards
 
to
 
switch
 
off
 
the
 f

oglamps,
 
the
 
sidelamps
 
will
 
then
 
switch
 
off.

133
DS3_en_Chap05_visibilite_ed01-2015
The temporary illumination of the dipped beam headlamps   after   the   vehicle's   ignition   has   been  
s

witched   off   makes   the   driver's   exit   easier  
w

hen   the   light   is   poor.
Switching on
F With  the   ignition   off,   "flash"   the   headlamps  u
sing   the   lighting   stalk.
F
 
A
  further   "headlamp   flash"   switches   the  
f

unction   off.
Switching off
The manual guide-me-home lighting switches off   automatically   after   a   set   time.
Manual guide-me-home
lighting
The sidelamps and dipped beam headlamps are   switched   on   automatically,   without   any  
a

ction on the part of the driver, when a low level
of
  external   light   is   detected   or   in   certain   cases  
o

f   activation   of   the   windscreen   wipers.
As
  soon   as   the   brightness   returns   to   an  
a

dequate   level   or   after   the   windscreen   wipers  
a

re   switched   off,   these   lamps   are   switched   off  
a

utomatically   and   the   daytime   running   lamps  
c

ome   on.
Automatic illumination of
headlamps
Activation
F Turn   ring   to   the   "AUTO"  position.   The  a
ctivation   of   the   function   is   confirmed   by  
t

he   display   of   a   message.
deactivation
F Turn  ring   to   a   position   other   than   "AUTO".  T
he deactivation of the function is
confirmed
  by   the   display   of   a   message.
Operating fault
In the event of a fault with the
sunshine  sensor,   the   lighting   come  
o

n,   this   warning   lamp   is   displayed  
o

n   the   instrument   panel   and/or   a  
m

essage   appears   in   the   screen,  
a

ccompanied   by   an   audible   signal.
Contact
 
a
 
CITROËN   or   a   qualified   workshop  
w

orkshop.
Visibility

DS3_en_Chap05_visibilite_ed01-2015
LED daytime running lampsThis daytime lighting, a signature of the vehicle, comprises   two   sets   of   light-emitting   diodes  
(

LEDs),   located   in   vertical   housings   below   each  
h

eadlamp.
On
  starting   the   vehicle,   in   daylight   the   daytime  
r

unning   lamps   come   on   automatically,   if   the  
l

ighting   stalk   is   in   position   "0" or "AUTO" .
If
  the   sidelamps   and   headlamps   are   switched  
o

n   manually   or   automatically,   the   daytime  
r

unning   lamps   go   off.
In
 
fog
 
or
 
snow,
 
the
 
sunshine
 
sensor
 
m

ay
 
detect
 
sufficient
 
light.
 
Therefore,
 
t

he
 
lighting
 
will
 
not
 
come
 
on
 
au

tomatically.
Do not cover the sunshine sensor,
coupled with the rain sensor and
located in the centre of the windscreen
behind
 
the
 
rear
 
view
 
mirror;
 
the
 
a

ssociated
 
functions
 
would
 
no
 
longer
 
be c

ontrolled.
Automatic "gu ide-me-
home" lighting
When the automatic illumination of headlamps f
unctions   is   activated,   if   the   ambient   light   level  
i

s   low   the   dipped   beam   headlamps   remain   on  
w

hen   switching   off   the   ignition.
Settings
Activation and deactivation, as well as the
duration  of   the   guide-me-home   lighting   can   be  
s

et   in   the   vehicle   configuration   menu   (except  
f

or   the   monochrome   screen   A,   for   which   the  
d

uration   is   fixed   at   60   seconds).

135
DS3_en_Chap05_visibilite_ed01-2015
Travelling abroad
LEd / Xenon front lamps
For motoring in countries that drive on the other s
ide   of   the   road,   it   is   necessary   to   adjust   the  
d

ipped   beams   so   as   to   not   dazzle   the   drivers   of  
a

pproaching
 v
ehicles.
F
 
R
aise   the   bonnet   for   access   to   the   adjuster  
(

one   adjuster   per   headlamp).
F
 
I
nsert   a   suitable   allen   key   (not   supplied)  
i

nto   the   hexagonal   head   of   the   adjuster.
F
 
T
urn   the   allen   key   half   a   turn   clockwise.
Headlamp adjustment
To avoid causing a nuisance to other road u
sers,   the   height   of   the   headlamps   should   be  
a

djusted   in   relation   to   the   load   in   the   vehicle.
0.
 
D
river   only   or   driver   +   front   passenger.
-.
 I

ntermediate
 s
etting.
1.
 5

  people.
-.
 
5
  people   +   load   in   the   boot.
2.
 D

river   only   +   maximum   authorised   load   in  
t

he   boot.
This
  position   is   sufficient   to   avoid   causing  
d

azzle.
Higher
  settings   may   limit   the   spread   of   light  
f

rom   the   headlamps.
The
  initial   setting   is   position   "0". On
  your   return,   don't   forget   to  
a

djust   your   headlamps   back   to   their  
i

nitial   setting,   by   carrying   out   these  
o

perations   in   reverse   order.
Visibility

DS3_en_Chap05_visibilite_ed01-2015
A. Courtesy lamp
B. Map reading lamps
Courtesy lam p
In this position, the courtesy lamp c
omes   on   gradually:
Courtesy lamp
- when  the   vehicle   is   unlocked,
-  w hen   the   key   is   removed   from   the   ignition,
-

w
hen a door is opened,
-
 
w
hen   the   remote   control   locking   button   is  
a

ctivated,   in   order   to   locate   your   vehicle.
It
  switches   off   gradually:
-
 
w
hen   the   vehicle   is   locked,
-
 
w
hen   the   ignition   is   switched   on,
-
 
3
0   seconds   after   the   last   door   is   closed.
Permanently
  off.
Permanent
 l

ighting.
With the "permanent lighting" mode, the duration of lighting   varies,   depending   on   the   circumstances:
- with the ignition off, approximately ten minutes,
- in energy economy mode, a pproximately   thirty   seconds,
- with the engine running, unlimited.
Map reading lamps
F With  the   ignition   on,   press   the  c
orresponding s witch.