display Citroen DS4 RHD 2013.5 1.G Workshop Manual

205Driving

Gear lever positions


N.
Neutral

R.
Reverse

1, 2, 3, 4, 5, 6. Gears in sequential mode.

AUTO.
This comes on when the automated
mode is selected. It switches off on
changing to sequential mode.



Displays in the instrument panel

Moving off



N
flashes in the instrument panel,
accompanied by an audible signal and a
message in the multifunction screen, if the
gear lever is not in position N
on starting.


Select position N
.


Press the brake pedal down fully.


Start the engine.

N
appears in the instrument panel
screen.


Select automated mode (position A
) or
sequential mode (position M
) or reverse
(position R
).


Release the parking brake unless it is
programmed to automatic mode.


Progressively take your foot off the
brake pedal.


Accelerate away.

AUTO
and 1
, 1
or R
appear in the
instrument panel screen.

You must press the brake pedal when
starting the engine.
The Foot on brake
warning
lamp comes on the instrument
panel, accompanied by an
audible signal and a message in the
screen, if the brake pedal is not pressed
on starting the engine.

Automatic gearbox


Gear selection gate

Six speed automatic gearbox which offers a
choice between the comfort of fully automatic
operation, enhanced by sport and snow
programmes, or manual gear changing.
Four driving modes are offered:


- automatic
operation for electronic
management of the gears by the gearbox,

- sport
programme for a more dynamic style
of driving,

- snow
programme to improve driving when
traction is poor,

- manual
operation for sequential changing
of the gears by the driver.


1.
Gear lever.

2.
Button "S"
(spor t)
.

3.
Button " 
" (snow)
.


Gear lever


P.
Park.


- Immobilisation of the vehicle, parking brake
on or off.

- Starting the engine.

R.
Reverse.


- Reversing manoeuvres, vehicle stationary,
engine at idle.

N.
Neutral.


- Immobilisation of the vehicle, parking brake
on.

- Starting the engine.

D.
Automatic operation.

M +/-
. Manual operation with sequential
changing of the six gears.



Press for wards to change up through the
gears.
or



Press rear wards to change down through
the gears.



Displays in the instrument panel

When you move the lever in the gate to select
a position, the corresponding indicator is
displayed in the instrument panel.

P.
Park

R.
Reverse

N.
Neutral

D.
Drive (Automatic driving)

S.
Sport
programme


. Snow
programme

1 to 6.
Gear engaged during manual operation

-.
Invalid value during manual operation

Manual operation




Select position M
for sequential
changing
of the six gears.


Push the lever towards the +
sign to
change up a gear.


Pull the lever towards the -
sign to change
down a gear.
It is only possible to change from one gear to
another if the vehicle speed and engine speed
permit; other wise, the gearbox will operate
temporarily in automatic mode.

D
disappears and the gears
engaged appear in succession in the
instrument panel.
If the engine speed is too low or too high, the
gear selected flashes for a few seconds, then
the actual gear engaged is displayed.
It is possible to change from position D

(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving
very slowly, the gearbox selects gear M1

automatically.
The sport and snow programmes do not
operate in manual mode.

Sport and snow programmes


Sport programme "S"




Press button "S"
, after starting the engine.
The gearbox automatically favours a dynamic
style of driving.

S
appears in the instrument panel.


Snow programme " 
"




Press button " 
", after starting the engine.
The gearbox adapts to driving on slippery
roads.
This programme improves starting and drive
when traction is poor.


appears in the instrument panel.



Return to automatic
operation



At any time, press the button selected
again to quit the programme engaged and
return to auto-adaptive mode.
These two special programmes supplement the
automatic operation in very specific conditions
of use.

211Driving

Invalid value during manual
operation
This symbol is displayed if a gear
is not engaged correctly (selector
between two positions).



Stopping the vehicle

Before switching off the engine, you can
engage position P
or N
to place the gearbox in
neutral.
In both cases, apply the parking brake to
immobilise the vehicle, unless it is programmed
to automatic mode.

If the lever is not in position P
, when the
driver's door is opened or approximately
45 seconds after the ignition is switched
off, there is an audible signal and a
message appears.



Return the lever to position P
;
the audible signal stops and the
message disappears.




Operating fault

When the ignition is on, the lighting of this
warning lamp, accompanied by an audible
signal and a message in the multifunction
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to back-up
mode and is locked in 3rd gear. You may feel
a substantial knock when changing from P

to R
and from N
to R
. This will not cause any
damage to the gearbox.
Do not exceed 60 mph (100 km/h), local speed
restrictions permitting.
Have it checked by a CITROËN dealer or a
qualified workshop.
This warning lamp may also come on if a door
is opened.
You risk damaging the gearbox:


- if you press the accelerator and
brake pedals at the same time,

- if you force the lever from position P

to another position when the
battery is flat.
To reduce fuel consumption when
stationary for long periods with the
engine running (traffic jam...), position
the gear lever at N
and apply the
parking brake, unless it is programmed
in automatic mode.

215Driving

Under-inflation alert


The loss of pressure detected does
not always lead to visible deformation
of the tyre. Do not rely on just a visual
check.

This alert is also displayed when one or
more wheels is not fitted with a sensor.

The alert is maintained until the tyre
or tyres concerned is reinflated or
repaired.

The aler t is given by the fixed illumination
of this warning lamp, accompanied by
an audible signal, and depending on
equipment, the display of a message.
In the event of a problem on one of the tyres,
the symbol or the message appears, according
to equipment, to identify it.


Reduce speed, avoid sudden steering
movements or harsh brake applications.


Stop as soon as it is safe to do so.


In the event of a puncture, use the
temporary puncture repair kit or the spare
wheel (according to equipment),
or


if you have a compressor, the one in the
temporary puncture repair kit for example,
check the four tyre pressures when cold,
or


if it is not possible to check the tyre
pressures at the time, drive carefully at
reduced speed.


Operating fault

The flashing and then fixed illumination
of the under-inflation warning lamp
accompanied by the illumination of the
"ser vice" warning lamp indicates a fault
with the system.
In this case, monitoring of the tyre pressures is
not assured.
Have the system checked by a CITROËN
dealer or a qualified workshop.

217Driving

Going into engine START mode

The "ECO"
warning lamp goes off
and the engine starts automatically:


- with a manual gearbox
, when you fully

depress the clutch pedal,

- with an electronic gearbox
:


●
gear lever in position A
or M
, when you
release the brake pedal,

●
or gear lever in position N
and the brake
pedal released, when you move the gear
lever to position A
or M
,

●
or when you engage reverse gear.




Special cases: START invoked
automatically
If the system has been deactivated
in STOP mode, the engine restarts
immediately. With a manual gearbox in STOP mode,
if a gear is engaged without fully
depressing the clutch pedal, a warning
lamp comes on or an alert message
is displayed asking you to depress the
clutch pedal to restart the engine.
At any time, press the "ECO OFF"
switch to
deactivate the system.
This is confirmed by the switch warning lamp
coming on accompanied by the display of a
message.

Deactivation

In this case the "ECO"
warning
lamp flashes for few seconds, then
goes off.

This operation is per fectly normal.
For safety reasons or to ensure smooth
operation, START mode is invoked
automatically when:


- you open the driver's door,

- you unfasten the driver's seat belt,

- the speed of the vehicle exceeds 15 mph
(25 km/h) with a manual gearbox or 7 mph
(11 km/h) with an electronic gearbox,

- the electric parking brake is being applied,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.

The system is reactivated automatically
at every new start using the key.


Reactivation

This system requires a specific battery with a
special specification and technology (reference
numbers available from a CITROËN dealer or a
qualified workshop).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the
system. In the event of a malfunction with the system,
the "ECO OFF"
switch warning lamp flashes,
then comes on continuously.
Have it checked by a CITROËN dealer or a
qualified workshop.

Operating fault
Maintenance

Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid any risk of injury
resulting from automatic operation of
START mode.
The Stop & Start system makes use
of advanced technology. All work on
this type of battery must be done only
by a CITROËN dealer or a qualified
workshop. Press the "ECO OFF"
switch again.
The system is active again; this is confirmed
by the switch warning lamp going off and the
display of a message.

In the event of a fault in STOP
mode, the vehicle may stall. All of
the instrument panel warning lamps
come on.
Depending on version, an alert
message may also be displayed asking
you to put the gear lever into position N

and put your foot on the brake pedal.
It is then necessary to switch off the
ignition, then restart the engine using
the key.

Memorising speeds
This memorisation of speeds applies to both the speed limiter and the cruise control.
You can memorise up to 5 speeds in the system. By default, a few speeds are already memorised.


With your Audio system




Go to the main menu by pressing the
"MENU"
button.


Select the "Personalisation-configuration"
menu and confirm.


Select " Vehicle parameters" menu and
confirm.


Select the "Driving assistance" line and
conform.


Select "Speeds memorised" line and
confirm.


Modify the speed.


Select " OK
" and confirm to save the
modifications.


With the eMyWay satellite
navigation system



Press the "MEM"
button to display the list
of speeds memorised.



Access

For safety reasons, the driver must
only carry out these operations when
stationary.


Go to the main menu by pressing the left
hand thumb wheel at the bottom of the
steering wheel.


Select the " Vehicle parameters" menu and
confirm.



Select the "Driving assistance" line and confirm.


Select the "Speeds memorised" line and
confirm.


Modify the speed.


Select " OK
" and confirm to save the
modifications.
These operations are only possible
when stationary with this system.


Selection

To select a memorised speed:



press and hold the " +
" or " -
" button; the
system stops at the nearest memorised
speed,


press and hold again the " +
" or " -
" button to
select another memorised speed.
A reminder of the speed and the state of the
system (on/off) is displayed in the instrument
panel.

223Driving
System which prevents the vehicle from
exceeding the speed programmed by the driver.
When the programmed speed limit is reached,
pressing the accelerator pedal no longer has
any effect.





Speed limiter

The speed limiter cannot, in any circumstances,
replace the need to respect speed limits,
nor can it replace the need for vigilance and
responsibility on the part of the driver.
The functions of this system are grouped
together on the steering mounted controls.


1.
Speed limiter mode selection wheel.

2.
Programmed value decrease button.

3.
Programmed value increase button.

4.
Speed limiter on / off button.

5.
List of memorised speeds display button.
(see the "Memorising speeds" section)



Steering mounted controls

The programmed information is grouped
together in the instrument panel screen.

6.
Speed limiter on / off indication.

7.
Speed limiter mode selection indication.

8.
Programmed speed value.

9.
Selection of a memorised speed.
(see "Memorising speeds")


Displays in the instrument panel


Operation

The speed limiter is switched on
manually: it
requires a programmed speed of at least
20 mph (30 km/h).
The speed limiter is switched off
by manual
operation of the control.
The programmed speed can be exceeded
temporarily by pressing the accelerator firmly
beyond the point of resistance.
To return to the programmed speed, simply
release the accelerator pedal.
The programmed speed remains in the memory
when the ignition is switched off.


Turn dial 1
to the "LIMIT"
position: the
speed limiter mode is selected but is not
switched on (Pause).
You do not have to switch the speed limiter on
in order to set the speed.



Set the speed value by pressing button 2

or 3
(e.g.: 55 mph (90 km/h)).


Programming

You can then change the programmed speed using buttons 2
and 3
:


- by + or - 1 mph (km/h) = short press,

- in steps of + or - 5 mph (km/h) = maintained press.
If speed memorisation is available and activated on your vehicle, the
programmed speed will stop at the closest memorised speed; refer to the
corresponding paragraph.



Switch the speed limiter on by pressing button 4
.


Switch the speed limiter off by pressing button 4
: the display
confirms that it has been switched off (Pause).


Switch the speed limiter back on by pressing button 4
again.



Exceeding the programmed speed

Pressing the accelerator pedal to exceed the programmed speed will not have
any effect unless you press the pedal firmly
past the point of resistance
.
The speed limiter is deactivated temporarily and the programmed speed,
which is still displayed, flashes.
Returning to the programmed speed, by means of intentional or unintentional
deceleration of the vehicle, automatically cancels the flashing of the
programmed speed. On a steep descent or in the event of
sharp acceleration, the speed limiter
will not be able to prevent the vehicle
from exceeding the programmed
speed.
To avoid any risk of jamming of the
pedals:


- ensure that the mat is positioned
correctly,

- do not fit one mat on top of another.



Exiting the speed limiter mode




Turn dial 1
to the "0"
position: the speed
limiter mode is deselected. It disappears
from the screen.



Operating fault

In the event of a fault with the speed limiter,
the speed is cleared resulting in flashing of the
dashes.
Have it checked by a CITROËN dealer or a
qualified workshop.