open bonnet Citroen DS5 2014 1.G Owner's Manual
[x] Cancel search | Manufacturer: CITROEN, Model Year: 2014, Model line: DS5, Model: Citroen DS5 2014 1.GPages: 372, PDF Size: 32.58 MB
Page 7 of 372
009009010010011011CHECKS TECHNICAL DATA AUDIO and
TELEMATICS
237 Opening the bonnet
238 Petrol engines
239 Diesel engines
240 Running out of fuel (Diesel)
241 Checking levels
245 Checks250 Petrol engines
251 Petrol weights
253 Diesel engines
255 Diesel weights
259 Dimensions
260 Identifi cation markings264 Emergency or assistance
267 eMyWay
323 Audio system
Page 39 of 372
37Monitoring
Service
on temporarily. A minor fault has occurred for which
there is no specific warning lamp. Identify the fault by reading the message shown in the
screen, such as, for example:
- opening of the doors, boot or bonnet,
- engine oil low level,
- screenwash low level,
- flat remote control battery,
- saturation of the particle emission filter (Diesel)
As soon as the traffic conditions permit,
regenerate the filter by driving at a speed of at
least 40 mph (60 km/h) until the ser vice warning
lamp goes off.
- a fault with the tyre under-inflation detection
system,
- ...
For any other faults, contact a CITROËN dealer or a
qualified workshop.
fixed. A major fault has occurred for which
there is no specific warning lamp. Identify the fault by reading the message shown
on the screen and contact a CITROËN dealer or a
qualified workshop.
fixed, associated with the
flashing and then fixed
display of the ser vice
indicator spanner.
The ser vicing inter val has been
exceeded. Only on Blue HDi Diesel versions.
Your vehicle must be ser viced as soon as possible.
Warning / indicator lamp
State
Cause
Action / Observations
Page 67 of 372
OFF
65Access
System which protects and provides a deterrent
against theft and break-ins. It provides the
following types of monitoring:
Alarm
- Exterior perimeter
The system checks for opening of the vehicle.
The alarm is triggered if anyone tries to open a
door, the boot or the bonnet...
- Interior volumetric
The system checks for any variation in the
volume in the passenger compartment.
The alarm is triggered if anyone breaks a
window, enters the passenger compartment or
moves inside the vehicle.
- Tilt
The system checks for any change in the
attitude of the vehicle.
The alarm is triggered if the vehicle is lifted,
moved or knocked.
Self-protection function
The system checks for the putting out of
ser vice of its components.
The alarm is triggered if the battery, the
button or the wires of the siren are put
out of service or damaged.
For all work on the alarm system,
contact a CITROËN dealer or a
qualified workshop.
Locking the vehicle with full
alarm system
Activation
Switch off the ignition and get out of the vehicle.
Press the locking button on the
remote control or lock the vehicle
using the Keyless Entry and
Starting system. The monitoring system is active: the indicator
lamp in the button flashes once per second.
After the locking button on the remote control
is pressed or the vehicle locked using the
Keyless Entry and Starting system, the exterior
perimeter monitoring is activated after a delay
of 5 seconds, the interior volumetric monitoring
after 45 seconds and the anti-tilt after
one minute and 30 seconds.
If an opening (door, boot...) is not closed
fully, the vehicle is not locked but the exterior
perimeter monitoring will be activated after
a delay of 45 seconds.
Press the unlocking button on
the remote control or unlock the
vehicle using the Keyless Entry
and Starting system.
Deactivation of the volumetric
monitoring
The volumetric protection system is
deactivated: the indicator lamp in the
button goes off.
Page 224 of 372
12 V battery
The presence of this label, in particular
with the Stop & Start system, indicates
the use of a 12 V lead-acid battery with
special technology and specification;
the involvement of a CITROËN dealer
or a qualified workshop is essential
when replacing or disconnecting the
battery. The battery is located under the bonnet.
To gain access to it:
open the bonnet using the interior release
lever, then the exterior safety catch,
remove the plastic cover on
the (+) terminal,
if necessary, unclip the fusebox to remove
the battery.
Access to the battery
Disconnecting the (+) cable
Raise the locking tab D
fully to release the
cable terminal clamp E
.
Reconnecting the (+) cable
Position the open clamp E
of the cable on
the positive post (+) of the battery.
Press vertically on the clamp E
to position
it correctly on the battery.
Lock the clamp by spreading the
positioning lug and then lowering the tab D
.
Do not apply excessive force on the
tab as locking will not be possible if the
clamp is not positioned correctly; start
the procedure again.
Procedure for starting the engine using another battery or charging a discharged battery.
Page 239 of 372
237Checks
Opening the bonnet
Opening
From inside
: pull the release lever, located
on the left below the dashboard, towards
you.
Before doing anything under the
bonnet, switch off the Stop & Start
system to avoid any risk of injury
resulting from an automatic change to
START mode.
Closing
Lower the bonnet and release it at the end
of its travel.
Check that it is latched correctly.
From the outside
: lift the safety catch and
raise the bonnet.
A bonnet strut opens the bonnet and holds it
open.
Because of the presence of electrical
equipment under the bonnet, it is
recommended that exposure to water
(rain, washing, ...) be limited.
Page 242 of 372
On vehicle fitted with HDi engines, the fuel
system must be primed if you run out of fuel;
refer to the corresponding engine compartment
view.
Running out of fuel (Diesel)
If the tank on your vehicle is fitted with
a misfuel prevention device, refer to the
"Misfuel prevention (Diesel)" section.
Fill the fuel tank with at least five litres
of diesel.
Open the bonnet.
If necessary, unclip the styling cover for
access to the priming pump.
Squeeze and release the priming pump
repeatedly until resistance is felt (there
may be resistance at the first press).
Operate the starter until the engine starts
(if the engine does not start at the first
attempt, wait around 15 seconds before
trying again).
If the engine does not start after a few
attempts, operate the priming pump again
then start the engine.
Clip the styling cover back in place.
Close the bonnet.
1.6 litre HDi engine
Fill the fuel tank with at least five litres of
Diesel.
Open the bonnet.
If necessary, unclip the style cover for
access to the priming pump.
Slacken the bleed screw.
Squeeze and release the priming pump
repeatedly until fuel appears in the
transparent pipe.
Tighten the bleed screw.
Operate the starter until the engine starts
(if the engine fails to start at the first
attempt, wait around 15 seconds before
trying again).
If the engine fails to start after a few
attempts, operate the priming pump again,
then the starter.
Put the style cover back in position and
clip it in place, ensuring that it has clipped
correctly.
Close the bonnet.
2 litre HDi engine
If the engine does not start first time,
don't keep trying but start the procedure
again from the beginning.
Page 245 of 372
243Checks
Coolant level
The coolant level should be close
to the "MA X" mark but should never
exceed it.
Fluid specifi cation
The coolant must conform to the
manufacturer's recommendations.
In addition, as the cooling system is
pressurised, wait at least one hour after
switching off the engine before carrying
out any work.
To avoid any risk of scalding, unscrew
the cap by two turns to allow the
pressure to drop. When the pressure
has dropped, remove the cap and top
up the level. When the engine is warm, the temperature of
the coolant is regulated by the fan.
The cooling fan may star t after switching
off the engine: take care with ar ticles and
clothing that might become caught by the
fan blades.
Specifi cation of the fl uid
To ensure optimum cleaning and to avoid
freezing, the fluid should never be topped up or
replaced by plain water.
In wintry conditions, the use of an ethyl alcohol
or methanol base fluid is recommended.
Screenwash / headlamp
wash level
To check the level or top up the fluid on vehicle
fitted with headlamp washers, immobilise the
vehicle and switch of the engine.
Before opening the bonnet, ensure that the
engine has completely stopped.
Open the screenwash reser voir filler cap.
Take and pinch the level gauge to block its
breather.
Remove the gauge completely from the reservoir
to read the level in the transparent section.
Top up if necessary.
Refit the filler cap to the reser voir and close the
bonnet.
Page 364 of 372
Instruments and controls
Courtesy lamps 159
Seat belt / passenger's front airbag
warning lamps display 187, 190
Rear view mirror 87
Cockpit glass roof 70 -71
Head-up display controls 131-132
Emergency or assistance call 181, 265
Door mirrors 86
Heating, ventilation 94-95
Digital air conditioning 96 -99
Demisting / defrosting 100
USB Player /
Auxiliary socket 90, 305 -309, 331-335
Dashboard fuses 219 -220
6 -speed manual gearbox 115
Automatic gearbox 116 -119
Electronic gearbox 120 -123
Gear shift indicator 124
Hill start assist 114
eMyWay 267-321
Setting the date/time 49
Vehicle configuration 312
Audio system / Bluetooth 323 -352
Setting the date/time 48
Vehicle configuration 347
Opening the bonnet 237
Rear electric windows 68- 69
12 V accessory socket 88, 89
Electric windows, deactivating 68-69
Page 367 of 372
365Visual search
Maintenance - Technical data
Dimensions 259
Identification markings 260
Checking levels 241-244
- oil
- brake fluid
- power steering fluid
- coolant
- screenwash/headlamp wash fluid
Checking components 245-247
- air filter
- passenger compartment filter
- oil filter
- electric parking brake
- brake pads / discs
Changing bulbs 211-218
- front
- rear
12V battery 222-224
Load reduction, economy mode 225
Engine compartment fuses 219, 221
Opening the bonnet 237
Petrol weights 251-252
Diesel weights 255 -258
Running out of fuel, Diesel 240
Under the bonnet, petrol 238
Under the bonnet, Diesel 239
Petrol engines 250
Diesel engines 253-254