steering Citroen DS5 2016 1.G Owner's Guide

Radio



QUESTION



ANSWER



SOLUTION


The quality of reception of
the radio station listened
to gradually deteriorates
or the stored stations do
not function (no sound,
87.5 Mhz is displayed...). The vehicle is too far from the transmitter used by the station
listened to or there is no transmitter in the geographical area
through which the vehicle is travelling. Activate the "RDS" function by means of the
short-cut menu to enable the system to check
whether there is a more power ful transmitter in
the geographical area.
The environment (hills, buildings, tunnels, basement car parks...)
block reception, including in RDS mode. This phenomenon is normal and does not
indicate a fault with the audio system.
The aerial is absent or has been damaged (for example when going
through a car wash or into an underground car park). Have the aerial checked by a CITROËN dealer.
I cannot find some radio
stations in the list of
stations received. The station is not received or its name has changed in the list. Press and hold the "List" button at the steering
mounted controls to update the list of stations
received or press on the system update function:
"Update list". Some radio stations send other information in place of their name
(the title of the song for example).
The system interprets this information as the name of the station.
The name of the radio
station changes.

1 Audio and Telematics







DS Connect Nav


GPS satellite navigation - Connectivity - Multimedia audio - Bluetooth ®
telephone


Contents
First steps 2
Steering mounted controls 4
Menus 5
Voice commands 6
Navigation 12
Connected navigation 28
Connectivity 38
Radio Media 50
Te l e p h o n e 6 2
Settings 74
Frequently asked questions 84

The system is protected in such a way that it will only operate in
your vehicle.

The link below gives access to OSS (Open Source Software)
codes for the system.
http://www.psa-peugeot-citroen.com/oss
As a safety measure and because it requires sustained attention
by the driver, the pairing of a Bluetooth mobile telephone with
the Bluetooth hands-free system of your audio system must be
done with the vehicle stationary
and the ignition on.
The display of the energy economy mode message signals that
a change to standby is imminent. Refer to the Energy economy
(mode) section of your vehicle's handbook.

Steering mounted controls



Media
(short press): change the
multimedia source.

Te l e p h o n e
(short press): call.

Call in progress
(short press):
access to telephone menu.

Te l e p h o n e
(long press): reject an
incoming call, end call, access to
telephone menu.






Voice commands
:
Short press, system voice
commands.
Long press, smartphone voice
commands via the system.

Decrease volume.



Radio
(rotate): automatic search for
the previous / next station.

Media
(rotate): previous / next track,
move in a list.

Shor t press
: Confirm a selection.
Other than selection, access to
presets.

Radio
: display the list of stations.

Media
: display the list of tracks.

Radio, press and hold
: update the
list of stations received.

Increase volume.

Voice commands






First steps





Steering mounted controls





Information - Using the system


Press the Push To Talk
button and tell me what you'd
like after the tone.
Remember you can interrupt
me at any time by pressing this button.
If you press it again while I'm waiting for
you to speak, it'll end the conversation.
If you need to start over, say "cancel".
If you want to undo something, say
"undo".
And to get information and tips at
any time, just say "help". If you ask to
me do something and there's some
information missing that I need, I'll
give you some examples or take you
through it step by step.
There's more information available
in "novice" mode. You can set the
dialogue mode to "expert" when you
feel comfortable.

To ensure that voice commands are
always recognised by the system,
please obser ve the following
recommendations:


- speak in a normal tone without
breaking up words or raising your
voice.

- always wait for the "beep" (audible
signal) before speaking,

- for best operation, it is
recommended that the windows
and opening roof (if fitted) be
closed to avoid inter ference from
extraneous noises.

- before makking a voice command,
ask other passengers to not speak.


The voice commands, with a choice
of 12 languages (English, French,
Italian, Spanish, German, Dutch,
Portuguese, Polish, Turkish, Russian,
Arabic, Brazilian), are made using the
language previously chosen and set in
the system.

The voice commands in Arabic for:
"Navigate to address" and "Display POI
in the city", are not available.

Example of a "voice command" for
navigation:

"Navigate to address, 11 Regent
Street, London"
.

Example of a "voice command" for
the radio and media:

"Play ar tist" "Madonna"
.

Example of a "voice command" for
the telephone:

"Call David Miller"
.
Pressing the end of the lighting
control stalk activates the voice
commands function.

7 Audio and Telematics






Global voice commands


These commands can be made from any screen page after pressing the voice command or telephone button located on the steering wheel, as
long as there is no telephone call in progress.


"Voice command"



Help message



Help

There are lots of topics I can help you with.
You can say: "help with phone", "help with navigation", "help with media" or "help with radio".
For an overview on how to use voice controls, you can say "help with voice controls".
Voice command help


Navigation help


Radio help


Media help


Te l e p h o n e h e l p


Set dialogue mode as <...>
Select "beginner" or "expert" mode.

Select profile <...>
Select profile 1, 2 or 3.

Ye s

Say "yes" if I got that right. Other wise, say "no" and we'll start that again.

No

"Navigation" voice commands


These commands can be issued from any screen page after pressing the voice command or telephone button on the steering wheel, as long as
there is no telephone call in progress.

Depending on the country, give the destination instructions (address) in the language used by the system.


"Voice command"



Help message



Navigate home

To start guidance or add a stopover, say "navigate to" and then the address or contact
name.
For example, "navigate to address 11 Regent Street, London", or "navigate to contact, John
Miller".
You can specify if it's a preferred or recent destination. For example, "navigate to preferred
address, Tennis club", "navigate to recent destination, 11 Regent Street, London".
Other wise, just say, "navigate home".
To see points of interest on a map, you can say things like "show hotels in Banbury" or
"show nearby petrol station".
For more information you can ask for "help with route guidance".
Navigate to work


Navigate to preferred address <...>


Navigate to contact <...>


Navigate to address <...>


Show nearby POI <...>


Remaining distance

To get information about your current route, you can say "tell me the remaining time",
"distance" or "arrival time".
Try saying "help with navigation" to learn more commands.
Remaining time


Arrival time


Stop route guidance

9 Audio and Telematics






"Radio Media" voice commands


These commands can be issued from any screen page after pressing the voice command or telephone button on the steering wheel, as long as
there is no telephone call in progress.


"Voice command"



Help message



Tune to channel <...>
You can pick a radio station by saying "tune to" and the station name or frequency.
For example "tune to channel Talksport" or "tune to 98.5 FM". To listen to a preset radio
station, say "tune to preset number". For example "tune to preset number five".

What's playing
To display the details of the current "track", "artist" and "album", you can say What's
playing

Play song <...>

Use the command "play" to select the type of music you'd like to hear. You can pick by
"song", "artist", or "album". Just say something like "play artist, Madonna", "play song, Hey
Jude", or "play album, Thriller".
Play artist <...>


Play album <...>


Media voice commands are available only for a USB connection.

"Voice command"



Help message



Call contact <...>

*
To make a phone call, say "call" followed by the contact name, for example: "Call David
Miller".
You can also include the phone type, for example: "Call David Miller at home".
To make a call by number, say "dial" followed by the phone number, for example,
"Dial 107776 835 417".
You can check your voicemail by saying "call voicemail".
To send a text, say "send quick message to", followed by the contact, and then the name
of the quick message you'd like to send.
For example, "send quick message to David Miller, I'll be late".
To display the list of calls, say "display calls".
For more information on SMS, you can say "help with texting".
Dial <...> *


Display contacts

*

Display calls

*

Call (message box | voicemail)

*

*
This function is available only if the telephone connected to the system supports downloading of contacts and recent calls and if the download has
been done.






"Telephone" voice commands


If a telephone is connected to the system, these voice commands can be issued from any main screen page after pressing the telephone
button on the steering wheel, as long as there is no telephone call in progress.
If there is no telephone connected by Bluetooth, a voice message announces: "Please first connect a telephone" and the voice session will be
closed.

11 Audio and Telematics



"Voice command"



Help message



Send text to <...>
To hear your messages, you can say "listen to most recent message".
When you want to send a text, there's a set of quick messages ready for you to use.
Just use the quick message name and say something like "send quick message to Bill
Carter, I'll be late".
Check the phone menu for the names of the supported messages.


Please say "call" or "send quick message to", and then select a line from the list.
To move around a list shown on the display, you can say "go to start", "go to end",
"next page" or "previous page".
To undo your selection, say "undo".
To cancel the current action and start again, say "cancel".
Listen to most recent message

*






"Test message" voice commands


If a telephone is connected to the system these voice commands can be issued from any main screen page after pressing the telephone button
on the steering wheel, as long as there is no telephone call in progress.
If no telephone has been connected by Bluetooth, a voice message announces: "Please first connect a telephone" and the voice session will be
closed.

*

This function is only available if the telephone connected to the system supports downloading of contacts and recent calls and if the download has
been done.
The system only sends predefined "Quick messages".

1






Receiving a call


An incoming call is announced by a ring and a
superimposed display in the screen.

Make a short press on the steering
mounted TEL
button to accept an
incoming call.

Make a long press.

on the steering mounted TEL
button
to reject the call.

Or
And

Select " End call
".

Press on the name of the telephone
chosen in the list to disconnect it.
Press again to connect it.


Select the basket at top right of the
screen to display a basket alongside
the telephone chosen.

Press on the basket alongside the
telephone chosen to delete it.












Managing paired telephones


This function allows the connection or
disconnection of a peripheral device as
well as the deletion of a pairing.

Press on Te l e p h o n e
to display the
primary page.

Press on the " OPTIONS
" button to
go to the secondary page.

Select " Bluetooth connection
" to
display the list of paired peripheral
devices.


Deleting a telephone