boot Citroen GRAND C4 PICASSO 2017 2.G Owner's Guide

287
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
This kit is installed in the storage box, under the
boot floor.This kit consists of a compressor and a sealant cartridge.
It allows the temporary repair
of a tyre.
You are then able to go to the nearest garage.
It is designed to repair most punctures which could affect the tyre, located on the tyre tread or
shoulder.
Its compressor can be used to check and adjust the pressure of the tyre.
Temporary puncture repair kit
Access to the kit
Depending on version, the kit is stowed under
the front passenger's seat or in the storage box
under the second row footwell.
List of tools
* Depending on equipment. All of these tools are specific to your vehicle
and can vary depending on equipment. Do not
use them for other purposes.
1.
1

2 V compressor.
C

ontains a sealant cartridge for the
temporary repair of a tyre and can also be
used for adjusting tyre pressures.
2.
C
hocks* to immobilise the wheels of the
vehicle.
3.
W
heel bolt cover remover*.
F

or removing the wheel bolt covers on alloy
wheels.
4.
R
emovable towing eye and front protective
cover opening tool.
For more information on To w i n g , refer to the
corresponding section.
8
In the event of a breakdown

294
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Spare wheel
The tools are installed in the boot under the
f l o o r.
Remove the boot carpet for access to them.
Access to the tools
List of tools*
Procedure for changing a wheel with a punctured tyre for the spare wheel using the tools provided with the vehicle.All of these tools are specific to your
vehicle and can vary according to the level
of equipment. Do not use them for other
purposes.
1.
W

heelbrace.
F

or removing the wheel trim and removing
the wheel bolts.
2.
C

hock for immobilising the vehicle (except
versions with manual gearbox).
3.
J

ack with integral handle.
F

or raising the vehicle.
4.
W

heel bolt cover remover.
F

or removing the wheel bolt covers on alloy
wheels.
5.
S

ocket for the security bolts (located in the
glove box).
F

or adapting the wheelbrace to the special
"security" bolts.
6.
T

owing eye and front protective cover
opening tool.
For more information about To w i n g , refer to
the corresponding section.
* Depending on equipment.
In the event of a breakdown

295
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
F Unscrew the central nut.
F R emove the fixing (nut and screw).
F

L
ift the spare wheel towards you from
the
rear.
F

R
emove the wheel from the boot. As the spare wheel is narrower than the
wheels on the vehicle, in the event of a
puncture, the punctured wheel must be
carried in the boot.
The spare wheel is located in the boot under the floor.
Access to the spare wheel
F Return the wheel to its housing.
F
U nscrew the nut a few turns on the screw.
F

P
osition the fixing (nut and screw) in the
middle of the wheel.
F

F
ully tighten the central nut to secure the
wheel correctly. F
R eturn the box to its position in the middle
of the wheel.
Taking out the wheel Putting the spare wheel back in
place
8
In the event of a breakdown

296
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Spare wheelProcedure for changing a wheel with a punctured tyre for the spare wheel using the tools provided with the vehicle.
Some of the tools are accessible from inside
the boot.
The wheel chock 2 as well as the wheelbrace
extension 6 are stowed under the right-hand
boot sill trim.
The wheelbrace 1 and the towing eye 7 are
stowed under the left-hand boot sill.
Access to the tools*3. Jack with integral handle. F or raising the vehicle.
4.
W

heel bolt cover remover.
F

or removing the wheel bolt covers on alloy
wheels.
5.
S

ocket for the security bolts (stowed in the
glove box).
F

or adapting the wheelbrace to the special
security bolts.
6.
W

heelbrace extension.
F

or lowering/raising the spare wheel
c a r r i e r.
7.
T

owing eye and front protective cover
opening tool.
For more information about To w i n g , refer to
the corresponding section.
Wheel with trim
When removing the wheel , detach the trim
first using the wheelbrace 1 pulling at the valve
passage hole.
When refitting the wheel , refit the trim
starting by placing its notch facing the valve
and press around its edge with the palm of your
hand.
All of these tools are specific to your vehicle
and can vary depending on equipment. Do not
use them for other purposes.
1.
W

heelbrace.
F

or removing the wheel trim and the wheel
fixing bolts.
2.
W

heel chock for immobilising the vehicle
(except versions with manual gearbox). *

D
epending on version. A complete set of tools
is provided with the spare wheel.
The other tools, the jack 3 and the tool for
removing the wheel bolt covers on alloy
wheels

4 , are stowed in a box attached to the
spare wheel.
The assembly is secured under the vehicle in
a carrier.
List of tools*
In the event of a breakdown

298
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
A punctured wheel from the vehicle
cannot be fitted under the vehicle. It
must be carried in the boot. Use a cover
to protect the boot.
F
P
ress the tongue, slide the tool box cover
to the centre and remove it for access to
the other tools ( jack and wheel bolt cover
remover for alloy wheels).
Putting the carrier and spare
wheel back in place
F Stow the corresponding tools in the box and close the cover.
F

P
osition the tool box on the ground.
Stowing the tools
F Return the tools to the box and stow the box in the vehicle's boot.
F

W
ind in the carrier by turning the
wheelbrace clockwise: once the cable is
fully wound in you should no longer feel
any resistance.
F

S
tow the other tools in the locations
provided in the boot.
When the spare wheel is fitted in place
of a punctured wheel, it is essential
to return the carrier and tools to their
normal position under the vehicle
before moving off.
In the event of a breakdown

303
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Fitting the "space-saver"
spare wheel
If your vehicle is fitted with alloy wheels,
when tightening the bolts on fitting, it
is normal to notice that the washers
do not come into contact with the
"space-saver" spare wheel. The wheel
is secured by the conical sur face of
each bolt.
After changing a wheel
To correctly store the punctured wheel
in the boot (not in the location for the
space-saver wheel ), first remove the
central cover.
When using the "space-saver" type
spare wheel, do not exceed 50 mph
(80
km/h).
Have the tightening of the bolts and the
pressure of the spare wheel checked
by a CITROËN dealer or a qualified
workshop without delay.
Have the punctured wheel repaired
and refitted to the vehicle as soon as
possible.
F

T

ighten the security bolt using the
wheelbrace 1 fitted with the security
socket 5
(depending on equipment).
F

T

ighten the other bolts using the
wheelbrace 1 o n l y.
F

R

efit the wheel bolt cover(s) (depending on
equipment).
F

S

tow the tools in the box. The tyre inflation pressures are given on this
label.
8
In the event of a breakdown

309
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Lamps on the tailgate
To change a sidelamp and brake lamp bulb:
F T urn the bulb holder a quarter of a turn
anti-clockwise and pull the bulb out.
F

C
hange the bulb.
Identify the failed bulb.
F

O

pen the boot.
F

R

emove the access cover.
F

R

emove the three lamp fixing screws A
.
F

D

isconnect the lamp connector.
F

C

arefully remove the lamp from the outside
by pressing the retaining clip B .
To change a reversing lamp or direction
indicator bulb:
F
U
se a standard pair of pliers to turn the
bulb holder a quarter turn anticlockwise,
and pull it out.
F
C
hange the bulb.
For reassembly, carry out these operations in
reverse order.
Model with LED lamps Model with conventional bulb lamps
8
In the event of a breakdown

311
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Lamps on the tailgate
Model with LED lamps
Model with conventional bulb lamps
Identify the failed bulb.
F

O

pen the boot.
F

R

emove the access cover. F

R

emove the three lamp fixing screws A .
F

D

isconnect the lamp connector.
F

C

arefully remove the lamp from its housing.
F

T

urn the bulb holder a quarter of a turn
anti-clockwise and pull the bulb out.
F

C

hange the bulb.
For reassembly, carry out these operations in
reverse order.
8
In the event of a breakdown

316
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
Fusebox 2Fuse N° Rating Functions
F7 10 ABoot 12 V socket, rear multimedia.
F8 20 ARear wiper.
F10 30 ALocks.
F17 5 AInstrument panel.
F18 5 AAutomatic gearbox gear selector.
F21 3 ASTART/STOP button.
F22 3 ARain and sunshine sensor, windscreen camera.
F24 5 AParking sensors, panoramic visual aid.
F27 5 AAutomatic gearbox.
F29 20 AAudio and telematic systems.
F32 15 A12 V sockets.
F35 5 AHeadlamp beam height adjustment, heated rear screen, radar.
F36 5 AInterior lighting: glove box, central storage, reading lamps,
courtesy lamps.
In the event of a breakdown

321
C4-Picasso-II_en_Chap08_en-cas-panne_ed02-2016
The Stop & Start system may not be
operational during the trip following the
first engine start.
In this case, the system will only be
available again after a continuous
period of immobilisation of the vehicle,
a period which depends on the ambient
temperature and the state of charge of
the battery (up to about 8 hours).
Do not force the lever as locking will
not be possible if the clamp is not
positioned correctly; start the procedure
again.
Disconnecting the (+) terminal
F

Ra

ise the lever A fully to release the
clamp
B .
F


R

emove the clamp B by lifting it off. Reconnecting the (+) terminal
F

Ra

ise the lever A fully.
F

R

efit the open clamp B on the (+) terminal.
F

P

ush the clamp B fully down.
F

L

ower the lever A to lock the clamp B
.
Disconnecting the battery
In order to maintain an adequate state
of charge for starting the engine, it is
recommended that the battery be disconnected
if the vehicle is taken out of service for a long
period.
Before disconnecting the battery:
F

c
lose all openings (doors, boot, windows,
roof),
F

s
witch off all electrical consumers (audio
system, wipers, lighting,
...),
F

s
witch off the ignition and wait for four
minutes.
At the battery, detach just the (+) terminal.Following reconnection of the battery
Following reconnection of the battery, switch on
the ignition and wait 1 minute before starting to
permit initialisation of the electronic systems.
However, if problems remain following this
operation, contact a CITROËN dealer or a
qualified workshop.
Referring to the corresponding section, you
must yourself reinitialise (depending on
version):
-

t
he remote control key,
-

t
he electric blind(s),
-
...
Quick-release terminal clamp
8
In the event of a breakdown