water pump DACIA SOLENZA 2004 Repair Manual

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 4
Power train group
The power train dismounting-remounting is to be performed on the engine compartment upper
part by means of a mobile lifting device.
The vehicle i s to be placed on a 2–columns
elevator.
Dismo unt :
- battery
- air filter inlet pipe;
- air filter assembly ;
- engine bonnet;
- front wheels.
Disconnect the oxygen sensor ( 1) connector
or the connectors of the two oxyge n sensors
(EURO 00 ).
Di smount : thermal protection screen and
descending tube from the exhaust manifold.
DISMOUNTIN G
Drain:
- the cooling circuit on the water pump
inlet pipe; - oil from gearbox;
- oil from engine if necessary;
- refrigerant fluid to a charging station
(vehicles with AC);
- oil from the power steering circuit
(vehicles with power steering).
- Oil from the power steeri ng circuit
(vehicles with power steering);
Dismo unt :
- engine shield;
- descending tube attachment screws
on support;
TIGHTENING MOMENTS) (daNm)
Right support attachment screw on engine 6.2
Hydr o-elastic buffer attachment nut 3.7
Left elastic buffer attachment nut 6.2
Whe els s c rew s 7.5
Power train- battery attachment screws 2.1
Connecting rod attachment nut on steering cross member support 6.2
Anti-roll connecting rod attachment screw on gearbox connecting rod 10.5
Control bar attachment screw on gearbox connecting rod 2.7
Pipes a ttachme nt s crews on comp ressor 2.1
High pressure pipe on DA pump 2.1
1
23
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 5
Power train group
Sw ing over the steeri ng knuckle and
extract the pl anetary t ransmission from the
planetary pinion of the gearbox. Dismount the left planetary transmission,
as follows: - dismount the steering knuckle nut;
- dismount the planetary transmission
attachment screws on the gearbox;
- dismount the brake calliper assembly ;
- dismount the shock absorber two
attachment screws on steering knuckle;
- swing over the steering knuckle and
dismount the planetary transmission. Dismount t he fuse box from the engine
compartment.
5
6
- collar ( 2) between the descending
tube and expansion chamber, remove the
descending tube; -anti-roll connecting rod.
Di sconnect the re verse dri ving contact
connector. Disenga ge the right planetary transmission,
as follows:
-dismount the brake calliper assembly ;
- dismount t he shock absorber t wo
attachment screw (4) on steering knuckle. Disconnect:
- connector (5 ) from the UCE (pull flap
(6) and then disengage); - engine wiring from engine fuse box;
4
- shock sensor connector;
- cooling engine fan connector;
- DA pressure sensor connector;
- mass wire from the gearbox
Dismount the battery protection shield.
Disconnect by means of the elastic clips pliers
MOT.1202-01 :
- hoses from radiator;
- hoses from thermostat support and from
water pump inlet pipe;
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 19
- clearance B (mm):
- minim 0.02
- maxim 0.86.
AT T E N T I O N !
Protect the distribution belt and the accessories belt in order to avoid the water and
cleaning materials splashing on them.
Chara cteristics
OIL PUMP
The oil pump is a gear wheels type.
Oil minimal pressure at 80°C is :
- at idling 1 bar
- at 4000 rpm 3 bar
Dismount the oil pump and check the
gearing clearances.
Check:
- cleara nce A ( mm)
- minim 0.110
- maxim 0.249
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 27
CYLINDER S BLOCK DISMOUNTING
Dismount :
- water inlet pipe and oil dipper rod
guide ( their sealing is performed by means of
rubber rings that must be replaced at each dis-
mounting); - clutch;
-engine flywheel, immobilized by means
of the MOT 582 ;
- lower crankcase;
-cr ankshaft gear;
- tightening roller;
-cr ankshaft closing casing;
Dismounting – Remounting
- water pump. Dismount
the oil pump attachment screws.
Dismo unt the oil pump and its driving chain.
Ma rk the connecting rod caps compared
with the connecting rod body.
AT T E N T I ON!
Do not use punches for marking in or-
der to avoid cracks occurring; a perma-
nent marker is to be used.
Dismo unt
- connecting rods caps and the bearings;
- jackets maintaining device MOT 484 or
clamps MOT 588 ;
- assembly jackets-pistons-connecting
rods; - bearings caps a nd their bearings;
- crankshaft and axial clearance bearings;
- bearings from the cylinders block.
PISTONS SHAFTS DI SMOUNTING
Place t he piston on the support lining up
the piston bolt (shaft) with the gap whole from
the support (two T lines for marking the whole
center are facilita ting the lining up).
Remove the bolts using a press by means
of the extraction mandrel E.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 33
Mount the lower casing and tighten the
sc rews to the required moment of 1 daNm.
Sealing is performed using RHODORSEAL
5661; the l ayer D must be 3 mm thick.
Do not forget to replace the two half-moon
gasket (in area A ) with new ones.
Dismounting – Remounting
Mount the engine flywheel; the flywheel
attaching screws thread must be lubricate us-
ing LOCTITE FRENETANCH .
Block the engine flywheel by means of the
geared sector MOT 582 and tighten t he a t-
tachment screws to the required moment of 5
– 5.5 daNm.
Center the clutch disk and mount the clutch
mechanism (see chapter 20”Clutch”). Mount
the water pump (sealing is performed
using LOCTITE 518 ).
Apply a layer of sealant material H, 0.6 – 1
mm thick , according to the drawing.
Tight e n t he att achm e nt sc re ws to t he
required moment of 1 -2 daNm.
vnx.su

ENGINE E7J-26210
ENGINE ASSEMBLY
10 - 38
2. Camshaft gear with marks
Rotate the engine until is reaching the Upper
Dead Point (cylinder 1 at ignition), and then con-
tinue until first item:
- adjust : exhaust 1
exhaust 3
- at second item :
-adjust : admission 1
admission 3
- at third item :
- adjust : exhaust 2
exhaust 4
- at fourth item :
- adjust : admission 2
admission 4
Dismounting – Remounting
Continue to mount:
- cylinder head cover equipped with a ne w cylinder head gasket, tighten the attachment
sc rews to the required moment of 1 daNm;
- water inlet pipe and the oil dipper guide (with new sealing rings);
- distribution casings;
-cr ankshaft pulley or pulleys; tighten the pulley hub screw to the required moment of 2
daN m, then to 68° ± 6°.
ATTENTION!
If the screw is not properly tighten, this may unloose, which may lead to the oil pump
no n-drive and to the distribution derangement, consequently to engine damaging.
- intake manifold and exhaust manifold, tighten the attachmen t screws to the required mo-
ment of 2.5 daNm;
- compressor and/or power steering support;
- alternator (see chapter 16”Alternator”);
- compressor- for vehicles equipped with air conditioning (see chapter 62 “Air condition-
ing”); -power steering pump-for vehicles equipped with power steering (see chapter 36 “Power
steering pump”);
-belt or accessories belt according to the method described in chapter 07” Accessories
b elt tensioning”.
vnx.su

IGNITION AND INJECTION
17
17 - 21
This diagnostic may detect:
-spark plug fouling or smoking,
-fou ling or modification from the normal value of the injectors flow,
-f uel supply system abnormalities (pressure controller, fuel pump,..)
-pr oblems with the electric connections for controlling fuel supply circuits and the injection.
Th e di ag nostic is performed by variations measurement of the engine prompt rotation speed.
Notice of a couple decrease is allowing the defective combustion recognition as failure cause.
Th is diagnostic is done almost permanently during driving. Non accomplishment of the diagnos-
tic or recognition of the existence of failure, is leading to other OBD diagnostics inhibition. This diagnostic is enabling the identification of two types of failures:
-de structive combustion misfires, which are causing the catalyst damage. These are gener-
ating the immediate blinking of the OBD indicator. -Polluting combustion misfires, leading to e xceeding a pre-established OBD pollution limit.
These ar e generating the permanent lighting of the OBD indicator, if the cause detection is
taken place during three consecutive running.
DE T ECT ION CONDITIONS
At the beginning, it must be checked if the “learning” stages of the adaptive values by the UCE
injection have been correctly performed. Also the preliminary conditions imposed when setting the
co ntact on and those from checking moment, must be accomplished.
Check by means of the CLIP tester if the bellow mentioned states are in the following configu-
ration:
ET0 14 Cylinder 1 recognition----------------------------------------------------------------- DONE
ET2 02 OBD diagnostic of combustion misfires taken into consideration--------------AC TIVE
Detection is accomplished after the water temperature is exceeding 75°C, at three rotation
steps, between idling and 4500 rot/min. It is also possible, test performing by maintaining the engine
at idling for a period of time of 11 minutes.
ATTENTION: after performing this test, the contact set ting on is imposed (key in M
position) before reading the r esults by means of the CLI P t ester. Any contact set ting off
be fore reading the test results, will lead to their wrong interpretation.
If after test performing, the CLIP tester is noticing the presence of the combustion mis-
f ires, refer to the diagnostic method related to this symptom.
CONFIRM ATION OF THE RE PARATION PE RFORM ING
-Check by m eans of the CLIP tester, the bellow states, which must have the following
c onfiguration:
ET0 14 Cylinder 1 recognition -------------------------------------------------------------------- DONE
ET2 02 OBD diagnostic of combustion misfires taken into consideration ----------------- AC TIVE
-N o failures is detected by the CLIP tester, and the OBD indicator must be off.
Diagnostic of combustion misfires detection
vnx.su

IGNITION AND INJECTION
17
17 - 63
Diagnostic – Conformity checking
RECOMMEND AT IONS The values show n on this conformity checking are only as indication.
Performing conditions : St opped engine, contact set on.
Sequence Function Parameter / Controlled state or acti on Visualization Diagnostic
and Observations
8F uel pump AC010 : Fuel pump relay The fuel pump In case of a
must be heard problem
running consult the AC010
dia gnostic
AC271 : low speed engine blower relay The engine
9 Engine blower must
blower be heard In case of a
running with problem low speed consult the
AC272 : high speed engine blower relay The engine ET035
(if equipped) blower must(ET036)
be heard running dia gnostic with high speed
10 Idling AC014 : idling regulator Place your hand In case of a
regulator under it to feel problem
it running. c onsult
the ET 039
dia gnostic
11 Canister AC016 : canister purging valve Canister purging In case of a
purging valve valve in operation problem
consult the ET032
dia gnostic
12 Climate AC003 : Climate control compressor Compressor In case of a
control must couple problem
consult theET070
dia gnostic
13 Indicators AC212 : water temperature indicator Indicator In case of a
must be on problem
AC213 : OBD indicator Indicator consult the
must be on AC212
AC 005 : rate changing indicator (if equippe d) Indicator / DF120
must be on (ET092)
diagnostic /
diagnostics
vnx.su

19
19 - 4
COOLING - EXHAUST - TANKCooling system diagram
ThermostatWa t e rpump
Composition :
1. Engine
2. Cooling radiator
3. Expansion vessel
4. Heating radiator
5. Thermostat support
6. Nozzle Ø 3
7. Purging screw
T. T h ermostat
The operation of the engine fan is controlled by the UCE injection, as follows:
1. For vehicles without air conditioning –cooling engine fan cooling is starting when water temperature is over 99°C;
– cooling engine fan cooling is stopping when water temperature is lower than 96°C.
2. For the vehicles with air conditioning. -cooling engine fan cooling is starting on first step when water temperature is over 99°C;
- cooling e ngine fan c ooling is start ing on second step when water temperature is over
104°C; - cooling engine fa n cooling is switching from second step to first step, when water
temperature is lower than 101°C; -engine fan cooling is stopping when water temperature is lower than 96°C.
vnx.su

19
19 - 11
COOLING - EXHAUST - TANKWa ter pump
DISMOUNTIN G
Place t he vehicle on a two columns elevator
Disconnect the battery
Drain the cooling circuit using the lower hose from the water pump.
Dismount :
- distribution belt ( see chapter 11 “Distribution belt”);
- tightening cam ( 1);
- water pump attachment screws and nut.
Remove the water pump through the upper part of the engine compartment.
TIGHTENING MOMENTS (daNm)
Tightening cam nut5
Crankshaft pulley hub screw2+680± 60
Right pendular support screws6.2
Hydro-elastic buffer nut3.7
W ater pump screws2.2
Water pump nut1
Wheels screws7.5
SPECIAL TOOLS
MOT. 1202-01 Pliers for elastic clips
MOT. 1505 Device for belts tension me asurement
MOT. 1135-01 Device for distribution belt tensioning
MOT. 545 Engine sustaining device
vnx.su