change key battery DACIA SUPERNOVA 2004 Repair Manual
[x] Cancel search | Manufacturer: DACIA, Model Year: 2004, Model line: SUPERNOVA, Model: DACIA SUPERNOVA 2004Pages: 933, PDF Size: 9.11 MB
Page 485 of 933
82A
HORN - ENGINE IMMOBILISER
82A - 18
If the states
remain unchanged, check the following:
- electric connections of the decoding bushing
- the electric connections between the E.C.U. decoder and the decoding bushing
- the tension of the battery must have more than 8V when the starter is activated.
If all these are conformable, proceed to the replacement of the decoding bushing, and then
check again the a .m. states.
II. SOLVING MODE
When an electric ke y head (or both) is damaged, order (Info TECH LINE 0248/213766) a
new set of two electronic heads, subject to the vehicle type, as follows: TRF key head set – item no. 6001 543 684, 1 set, for DSN equipped with
anti intrusion (CLIMA or RAPSODIE)
TR-TRF key head set – item no. 6001 544 452, 1 set, for DSN without anti
intrusion (CLIMA or RAPSODIE)
TR key head set – item no. 6001 543 683, 1 set, for DSN EUROPA
Send to Tech Line (0248 213766), the chassis series no, the anti starting code of the damaged
key heads, the a nti starting code of the ne w key heads, and they will sent at their turn, to the
service center, the repairing code (taking into account that this code has a special regime). Additionally , there are necessary the new key heads, the E.C.U. decoder (obligatory TRF, if
the vehicle is equipped with central locking), the repairing code of the computer; proceed then to
the replacemen t of these items performing the following operation:
A) Replacement- c hecking electronic key heads :
Replace t he damaged key heads with the new ones (the metal insertions remain the same),
then by means of the CLIP tester, selecting COMPUTER TEST- ANTI STARTING- STATE
LIST, check following states with both keys:
If the states are in the following configuration, when setting the contact on, consecutively with
both keys:
ANTI STARTING……………………………………………..........ACTIVE
RECEIVED KEY CODE………………………………………….. ACTIVE
ACCEPTED KEY CODE…………………………………………PASSIVE DIAGNOSTIC
vnx.su
Page 510 of 933
82B
HORN - ENGINE IMMOBILISER
82B - 43
THE PIN CODE
The PIN code is formed of four figures and it can be used only for deactivating the anti intrusion
s ystem, if this operation can not be performed by pushing the deactivating button from the RF
remote control of the vehicle. For introducing the PIN code, perform as follows:-set on the contact key in the M position and take it off it for three times in seven seconds,
after which the anti intrusion LED indicator will switch on for three seconds; -set on the contact again on the M position and maintain it until the number of the L ED
blinks is e qual with the first figure of the PIN code, then take off the contact; -set on the contact in the M position and maintain it until the number of LED blinks is equal
w ith the second figure of the PIN code, then take off the contact;
-perform the above mentioned method in order to introduce the third and the fourth figure
of the PIN code;
-after that, the system is deactivated and the siren stops automatically;
- set on the contact again – the anti LED indicator must switch on, confirming in this way
that the c orrect introduction of the PIN code.
AT TENT ION
If it i s necessary the checking of the PIN code, t his will be pe rformed
only after al least 20 seconds have passed, since the anti intrusion ECU has been
connected to the vehicle’s wiring or since the connecting of t he vehicle’s battery.
The COBRA anti intrusion system can operate in t hree different modes (2,3 or 4).
For the Super Nova vehicles, the system has been programmed to work in the second operation
mode. If by mistake the PIN code was introduced in less than 20 seconds since the battery
connecting or since connecting the anti intrusion ECU, this can involve the change of the operation
way of the system, which will generate errors during the operation. There is, although, the possibility
of reprogramming the correct operation way (type 2) and in this purpose, perform the following
operations : - disconnect and then reconnect the anti intrusion ECU; when connecting the anti intrusion
ECU the anti intrusion LED indicator will switch on once, confirming the correct connecting;
-af ter at least 5 seconds from the previous operation, but no more than 20 second from it,
perform the following operation s:
-s et on the contact key in the M position for three times and then release it;
- the anti intrusion LED indicator will switch on for three seconds and then will switch off;
- set on again the contact key in the “M” position and maintain it, counting two blinks of the
anti intrusion LED indicator, then take off the contact;
- the LED indicator will blink for two times in two series, confirming in this way the proper
performance of the previous operations;
press the doors locking button of the dashboard, in order to lock and unlock the doors; the anti
intrusion LED indicator must not blink;
vnx.su