Automatic DAEWOO LACETTI 2004 Service Repair Manual

v
TABLE OF CONTENTS
Section 0B General Information
Section 1 Engine
Section 1A General Engine Information
Section 1C1 1.4L/1.6L DOHC Engine Mechanical
Section 1C2 1.8L DOHC Engine Mechanical
Section 1D Engine Cooling
Section 1E Engine Electrical
Section 1F Engine Controls
Section 1G Engine Exhaust
Section 2 Suspension
Section 2A Suspension Diagnosis
Section 2B Wheel Alignment
Section 2C Front Suspension
Section 2D Rear Suspension
Section 2E Tires and Wheels
Section 3 Driveline/Axle
Section 3A Automatic Transaxle Drive Axle
Section 3B Manual Transaxle Drive Axle
Section 4 Brakes
Section 4A Hydraulic Brakes
Section 4B Master Cylinder
Section 4C Power Booster
Section 4D Front Disc Brakes
Section 4E1 Rear Disc Brakes
Section 4E2 Rear Drum Brakes
Section 4F Antilock Brake System
Section 4G Parking Brake
Section 5 Transmission/Transaxle
Section 5A1 ZF 4HP16 Automatic Transaxle
Section 5A2 AISIN Automatic Transaxle
Section 5B Five-Speed Manual Transaxle
Section 5C Clutch
Section 6 Steering
Section 6A Power Steering System
Section 6B Power Steering PumpSection 6C Power Steering Gear
Section 6E Steering Wheel and Column
Section 7 Heating, Ventilation, and Air
Conditioning (HVAC)
Section 7A Heating and Ventilation System
Section 7B Manual Control Heating, Ventilation,
and Air Conditioning System
Section 7D Automatic Temperature Control HVAC
Section 8 Restraints
Section 8A Seat Belts
Section 8B Supplemental Inflatable Restraints
(SIR)
Section 9 Body and Accessories
Section 9A Body Wiring System
Section 9B Lighting Systems
Section 9C Horns
Section 9D Wipers/Washer Systems
Section 9E Instrumentation/Driver Information
Section 9F Audio Systems
Section 9G Interior Trim
Section 9H Seats
Section 9I Waterleaks
Section 9J Windnoise
Section 9K Squeaks and Rattles
Section 9L Glass and Mirrors
Section 9M Exterior Trim
Section 9N Frame and Underbody
Section 9O Bumpers and Fascias
Section 9P Doors
Section 9Q Roof
Section 9R Body Front End
Section 9S Body Rear End
Section 9T1 Remote Keyless Entry and Anti–Theft
System
Section 9T2 Immobilizer Anti–Theft System

SECTION : 0B
GENERAL INFORMATION
TABLE OF CONTENTS
SPECIFICATIONS0B–1 . . . . . . . . . . . . . . . . . . . . . . . . . .
Technical Data 0B–1. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Vehicle Dimensions and Weights 0B–6. . . . . . . . . . . .
Standard Bolt Specifications 0B–8. . . . . . . . . . . . . . . .
MAINTENANCE AND REPAIR0B–9 . . . . . . . . . . . . . . .
MAINTENANCE AND LUBRICATION 0B–9. . . . . . . . . .
Normal Vehicle Use 0B–9. . . . . . . . . . . . . . . . . . . . . . .
Explanation of Scheduled Maintenance
Services 0B–9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Scheduled Maintenance Charts 0B–10. . . . . . . . . . . .
OWNER INSPECTIONS AND SERVICES 0B–12. . . . .
Whle Operating The Vehicle 0B–12. . . . . . . . . . . . . . . At Each Fuel Fill 0B–12. . . . . . . . . . . . . . . . . . . . . . . . .
At least Monthly 0B–12. . . . . . . . . . . . . . . . . . . . . . . . . .
At least Twice a Year 0B–12. . . . . . . . . . . . . . . . . . . . .
Each Time The Oil is Changed 0B–13. . . . . . . . . . . . .
At Least Annually 0B–13. . . . . . . . . . . . . . . . . . . . . . . .
Recommended Fluids and Lubricants 0B–14. . . . . . .
GENERAL DESCRIPTION AND SYSTEM
OPERATION0B–15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Repair Instructions 0B–15. . . . . . . . . . . . . . . .
GENERAL DESCRIPTION 0B–16. . . . . . . . . . . . . . . . . .
Vehicle and Component Identification 0B–16. . . . . . .
Vehicle Lifting Procedures 0B–21. . . . . . . . . . . . . . . . .
SPECIFICATIONS
TECHNICAL DATA
Performance – Manual Transaxle
Application1.4L DOHC1.6L DOHC1.8L DOHC
Maximum Speed175 km/h (108.7 mph)187 km/h (116.2 mph)194 km/h (120.5 mph)
Minimum Turning Radius5.2 m (17.1 ft)


Performance – Automatic Transaxle
Application1.4L DOHC1.6L DOHC1.8L DOHC
Maximum Speed–175 km/h (108.7 mph)184 km/h (114.3 mph)
Minimum Turning Radius–5.2 m (17.1 ft)

GENERAL INFORMATION 0B – 3
DAEWOO V–121 BL4
Automatic Transaxle
Application1.4L DOHC1.6L DOHC1.8L DOHC
Maker–AISINZF
Type or Model–81–40LE4HP16
Gear Ratio :
1st
2nd
3rd
4th
Reverse–
–
–
–
–2.875:1
1.568:1
1.000:1
0.697:1
2.300:12.719:1
1.487:1
1.000:1
0.717:1
2.529:1
Final Drive Ratio–3.750:13.945:1
Oil Capacity–5.77±0.2L (6.1±0.2 qts)6.9±0.2L (7.3±0.2 qts)
Brake
Application1.4L DOHC1.6L DOHC1.8L DOHC
Booster Size :
Single
Dual241.3 mm (9.5 in.)
177.8 and 203.2 mm
(7 and 8 in.)






Master Cylinder Diameter22.22 mm (0.875 in.)


Booster Ratio5.5 : 1


Front Brake :
Disc Type
Disc SizeVentilated
256 mm (10 in.)






Rear Brake (Drum) :
Drum Inside Diameter
Wheel Cylinder Diame-
ter200 mm (7.9 in.)
20.64 mm (0.813 in.)






Rear Brake (Disc) :
Disc Type
Disc SizeSolid
258 mm (10.2 in.)






Fluid Capacity0.5L (0.5 qts)


Tire and Wheel
Application1.4L DOHC1.6L DOHC1.8L DOHC
Tire Size195/55R15


Standard Wheel Size6Jx15 (Steel)


Optional Wheel Size6Jx15 (Alloy)


Inflation Pressure at Full
Load30 psi (207 kPa)

0B – 6IGENERAL INFORMATION
DAEWOO V–121 BL4
VEHICLE DIMENSIONS AND WEIGHTS
Vehicle Dimensions
Application1.4L DOHC1.6L DOHC1.8L DOHC
Overall Length
4 Door
5 Door H/B4,500 mm (177.2 in.)
4,295 mm (169.1 in.)






Overhang :
4 Door
Front
Rear
885 mm (34.8 in.)
1,015 mm (40.0 in.)






5 Door H/B
Front
Rear
902 mm (35.5 in.)
793 mm (31.2 in.)






Overall Width1,725 mm (67.9 in.)


Overall Height1,445 mm (56.9 in.)


Minimum Ground Clear-
ance160 mm (6.3 in.)


Wheel Base2,600 mm (102.4 in.)


Tread :
Front
Rear1,480 mm (58.3 in.)
1,480 mm (58.3 in.)






Vehicle Weights
4 Door
Application1.4L DOHC1.6L DOHC1.8L DOHC
Manual :
Curb Weight :
Standard
Optional1,175 kg (2,590 lb)
1,225 kg (2,701 lb)1,180 kg (2,601 lb)
1,230 kg (2,712 lb)1,210 kg (2,668 lb)
1,260 kg (2,778 lb)
Gross Vehicle Weight1,660 kg (3,660 lb)1,665 kg (3,671 lb)1,695 kg (3,737 lb)
Automatic :
Curb Weight :
Standard
Optional–
–1,190 kg (2,624 lb)
1,240 kg (2,734 lb)1,235 kg (2,723 lb)
1,285 kg (2,833 lb)
Gross Vehicle Weight–1,675 (3,693 lb)1,720 kg (3,792 lb)
Passenger Capacity5


Optional Weight : ABS, Sun Roof, A/C

GENERAL INFORMATION 0B – 7
DAEWOO V–121 BL4
Vehicle Weights
5 Door H/B
Application1.4L DOHC1.6L DOHC1.8L DOHC
Manual :
Curb Weight :
Standard
Optional1,170 kg (2,580 lb)
1,220 kg (2,690 lb)1,175 kg (2,590 lb)
1,225 kg (2,701 lb)1,205 kg (2,657 lb)
1,255 kg (2,767 lb)
Gross Vehicle Weight1,645 kg (3,627 lb)1,650 kg (3,638 lb)1,680 kg (3,704 lb)
Automatic :
Curb Weight :
Standard
Optional–
–1,185 kg (2,612 lb)
1,235 kg (2,723 lb)1,230 kg (2,712 lb)
1,280 kg (2,822 lb)
Gross Vehicle Weight–1,660 kg (3,660 lb)1,705 kg (3,759 lb)
Passenger Capacity5


Optional Weight : ABS, Sun Roof, A/C

GENERAL INFORMATION 0B – 9
DAEWOO V–121 BL4
MAINTENANCE AND REPAIR
MAINTENANCE AND LUBRICATION
NORMAL VEHICLE USE
The maintenance instructions contained in the mainte-
nance schedule are based on the assumption that the ve-
hicle will be used for the following reasons:
S To carry passengers and cargo within the limitation
indicated on the tire placard located on the edge of
the driver’s door.
S To be driven on reasonable road surfaces and with-
in legal operating limits.
EXPLANATION OF SCHEDULED
MAINTENANCE SERVICES
The services listed in the maintenance schedule are fur-
ther explained below. When the following maintenance
services are performed, make sure all the parts are re-
placed and all the necessary repairs are done before driv-
ing the vehicle. Always use the proper fluid and lubricants.
Drive Belt Inspection
When a separate belt drives the power steering pump, the
air conditioning compressor and the generator, inspect it
for cracks, fraying, wear and proper tension. Adjust or re-
place the belt as needed.
Engine Oil and Oil Filter Change
API Classifications of Engine Oil
The International Lubricant Standardization and Approval
Committee (ILSAC) and American Petroleum Institute
classifies engine oils according to their performance quali-
ty. Always use oil rated API–SL (ILSAC GF–III) or better.
Engine Oil Viscosity
Engine oil viscosity (thickness) has an effect on fuel econ-
omy and cold weather operation. Lower viscosity engine
oils can provide better fuel economy and cold weather per-
formance; however, higher temperature weather condi-
tions require higher viscosity engine oils for satisfactory lu-
brication. Using oils of any viscosity other than those
viscosities recommended could result in engine damage.
Cooling System Service
Drain, flush and refill the system with new coolant. Refer
to ”Recommended Fluids And Lubricants” in this section.
Fuel Micro–Filter Replacement
Replace the engine fuel filter every 45,000 km (27,000
miles).
Air Cleaner Element Replacement
Replace the air cleaner element every 45,000 km (27,000
miles).Replace the air cleaner more often under dusty conditions.
Throttle Body Mounting Bolt Torque
Check the torque of the mounting bolts.
Tighten the throttle body mounting bolts to 15 NSm (11 lb–
ft) if necessary.
Spark Plug Replacement
Replace spark plugs with the same type.
Spark Plug Wire Replacement
Clean wires and inspect them for burns, cracks or other
damage. Check the wire boot fit at the DIS module and at
the spark plugs. Replace the wires as needed.
Brake System Service
Check the disc brake pads and the drum brake linings ev-
ery 15,000 km (9,000 miles) or 12 months. Check the pad
and the lining thickness carefully. If the pads or the linings
are not expected to last to the next scheduledmaintenance
service, replace the pads or the linings. Check the breath-
er hole in the brake fluid reservoir cap to be sure it is free
from dirt and the passage is open.
Transaxle Service
The manual transaxle fluid does not require changing. For
automatic transaxles, refer to ”Scheduled Maintenance
Charts” in this section.
Tire and Wheel Inspection and Rotation
Check the tires for abnormal wear or damage. To equalize
wear and obtain maximum tire life, rotate the tires. If irreg-
ular or premature wear exists, check the wheel alignment
and check for damaged wheels. While the tires and
wheels are removed, inspect the brakes. Refer to ”Each
Time The Oil Is Changed” in this section.
Tire Rotation

GENERAL INFORMATION 0B – 11
DAEWOO V–121 BL4
Chassis and Body
Maintenance ItemMaintenance Interval
Kilometers or time in months, whichever comes first
x 1,000 km1153045607590105120
x 1,000 miles0.6918273645546372
Months–1224364860728496
Interior air filter (A/C)RRRRRRRR
Exhaust pipes & mountingsIIIIIIII
Brake/Clutch fluid (1) (4)IIRIRIRIR
Front brake pads and discs(3)IIIIIIII
Rear brake pads & discs or drums and
linings (3)IIIIIIII
Parking brakeIIIIIIIII
Brake line and connections (Including
booster)IIIIIIII
Manual Transaxle Oil *(1)IIIIIIII
Automatic transaxle fluid *(1) (5)IIIIIIII
Tighten chassis and underbody bolts
and nutsIIIIIIII
Tire condition and inflation pressureIIIIIIIII
Wheel alignment (2)Inspect when abnormal condition is noted
Steering wheel and linkageIIIIIIII
Power steering fluid & lines* (1)IIIIIIIII
Drive shaft bootsIIIIIIII
Seat belts, buckles and anchorsIIIIIIII
Lubricate locks, hinges and hood
latchIIIIIIII
Chart Symbols:
I – Inspect and if necessary correct, clean, replenish, or adjust.
R – Replace or change:
(1) Refer to Recommended Fluids And Lubricants.
(2) And if necessary, rotate and balance wheels.
(3) More frequent if operated under severe conditions: short distance driving, extensive idling, frequent low–speed oper-
aion in stop and go traffic, or driving in dusty conditions.
(4) Change the brake/clutch fluid every 15,000 km (9,000 miles), if the vehicle is mainly driven under the following severe
conditions: driving in hilly or mountainous terrain, or towing a trailer/caravan frequently.
(5) 1.8 DOHC model (ZF 4HP16 Automatic Transaxle): Change automatic transaxle fluid every 60,000 Km (36,000 miles)
if the vehicle is mainly driven under any of the following severe conditions:
S In heavy city traffic where the outside temperature regularly reaches 32°C (90°F) or higher, or
S In hilly or mountainous terrain, or
S When doing frequent trailer towing, or
S Uses such as taxi, police or delivery service.

GENERAL INFORMATION 0B – 13
DAEWOO V–121 BL4
EACH TIME THE OIL IS CHANGED
Automatic Transaxle Fluid
Refer to fluid level service procedure of Section 5A, ZF
4HP16 Automatic Transaxle.
Manual Transaxle
Check the fluid level and add fluid as required. Refer to
Section 5B, Five–Speed Manual Transaxle.
Brake System Inspection
This inspection should be done when the wheels are re-
moved for rotation. Inspect the lines and the hoses for
proper hookup, binding, leaks, cracks, chafing, etc. In-
spect the disc brake pads for wear. Inspect the rotors for
surface condition. Also inspect the drum brake linings for
wear and cracks. Inspect other brake parts, including the
drums, the wheels cylinders, the parking brake, etc., at the
same time. Check the parking brake adjustment. Inspect
the brakes more often if habit or conditions result in fre-
quent braking.
Steering, Suspension and Front Drive Axle
Boot And Seal Inspection
Inspect the front and rear suspension and the steering
system for damaged, loose or missing parts, signs of wear
or lack of lubrication. Inspect the power steering lines and
the hoses for proper hookup, binding, leaks, cracks, chaf-
ing, etc. Clean and inspect the drive axle boot and seals
for damage, tears or leakage. Replace the seals if neces-
sary.
Exhaust System Inspection
Inspect the complete system (including the catalytic con-
verter if equipped). Inspect the body near the exhaust sys-
tem. Look for broken, damaged, missing, or out–of–posi-
tion parts as well as open seams, holes, loose
connections, or other conditions which could cause heat
buildup in the floor pan or could let exhaust fumes seep
into the trunk or passenger compartment.
Throttle Linkage Inspection
Inspect the throttle linkage for interference or binding,
damaged, or missing parts. Lubricate all linkage joints and
throttle cable joints, the intermediate throttle shaft bearing,
the return spring at throttle valve assembly, and the accel-
erator pedal sliding face with suitable grease. Check the
throttle cable for free movements.
Engine Drive Belts
Inspect all belts for cracks, fraying, wear and proper ten-
sion. Adjust or replace the belts as needed.
Hood Latch Operation
When opening the hood, note the operation of the secon-
dary latch. It should keep the hood from opening all the
way when the primary latch is released. The hood must
close firmly.
AT LEAST ANNUALLY
Lap and Shoulder Belts Condition and
Operation
Inspect the belt system including: the webbing, the
buckles, the latch plates, the retractor, the guide loops and
the anchors.
Movable Head Restraint Operation
On vehicles with movable head restraints, the restraints
must stay in the desired position.
Spare Tire and Jack Storage
Be alert to rattles in the rear of the vehicle. The spare tire,
all the jacking equipment, and the tools must be securely
stowed at all times. Oil the jack ratchet or the screw mech-
anism after each use.
Key Lock Service
Lubricate the key lock cylinder.
Body Lubrication Service
Lubricate all the body door hinges including the hood, the
fuel door, the rear compartment hinges and the latches,
the glove box and the console doors, and any folding seat
hardware.
Transaxle Neutral Switch Operation on
Automatic Transaxle
CAUTION : Take the following precautions because
the vehicle could move without warning and possibly
cause personal injury or property damage:
S Firmly apply the parking brake and the regular
brakes.
S Do not use the accelerator pedal.
S Be ready to promptly turn off the ignition if the ve-
hicle starts.
On automatic transaxle vehicles, try to start the engine in
each gear. The starter should crank only in P (Park) or N
(Neutral).
Parking Brake and Transaxle P (Park)
Mechanism Operation
CAUTION : In order to reduce the risk of personal in-
jury or property damage, be prepared to apply the reg-
ular brakes promptly if the vehicle begins to move.
Park on a fairly steep hill with enough room for movement
in the downhill direction. To check the parking brake, with
the engine running and the transaxle in N (Neutral), slowly
remove foot pressure from the regular brake pedal (until
only the parking brake is holding the vehicle).
To check the automatic transaxle P (Park) mechanism’s
holding ability, release all brakes after shifting the trans-
axle to P (Park).
Underbody Flushing
Flushing the underbody will remove any corrosive materi-
als used for ice and snow removal and dust control. At
least every spring clean the underbody. First, loosen the
sediment packed in closed areas of the vehicle. Then flush
the underbody with plain water.

0B – 14IGENERAL INFORMATION
DAEWOO V–121 BL4
Engine Cooling System
Inspect the coolant and freeze protection fluid. If the fluid
is dirty or rusty, drain, flush and refill the engine cooling
system with new coolant. Keep the coolant at the proper
mixture in order to ensure proper freeze protection, corro-sion protection and engine operating temperature. Inspect
the hoses. Replace the cracked, swollen, or deteriorated
hoses. Tighten the clamps. Clean the outside of the radia-
tor and the air conditioning condenser. Wash the filler cap
and the neck. Pressure test the cooling system and the
cap in order to help ensure proper operation.
RECOMMENDED FLUIDS AND LUBRICANTS
UsageCapacityFluid/Lubricant
Engine Oil3.75L (4.0 qt) : 1.4L DOHC
3.75L (4.0 qt) : 1.6L DOHC
4.0L (4.2 qt) : 1.8L DOHCAPI SL (ILSAC GF–III) grade or better
SAE 5W–30, SAE10W–30, SAE15W–40
(Cold area : SAE5W–30
Hot area : SAE 15W–40)
Engine Coolant7.0L (7.49 qt) : 1.4L DOHC
7.2L (7.6 qt) : 1.6L DOHC
7.4L (7.8 qt) : 1.8L DOHCMixture of water and good quality ethylene gly-
col base antifreeze (year–round coolant)
Brake Fluid and Clutch Fluid0.5L (0.5 qt)DOT–3 or DOT–4
Power Steering System1.1L (1.2 qt)DEXRON®–III or DEXRON®–IID
Automatic Transaxle5.77 ± 0.2L (6.1 ± 0.2 qts) :
1.6L DOHC (AISIN 81–40LE)ESSO JWS 3309 or ISU DEXRON III
6.9 ± 0.2L (7.3 ± 0.2 qts) :
1.8L DOHC (ZF 4HP16)ESSO LT 71141 or TOTAL ATF H50235
Manual Transaxle1.8L (2.0 qt)Manual Transaxle Fluid
SAE80W (Cold Area : SAE 75W)
Manual Transaxle Shift LinkageAs requiredMultipurpose type grease meeting require-
ments NLGI No. 1 or 2
Key Lock CylindersAs requiredSilicone lubricant
Automatic Transaxle Shift Link-
ageAs requiredEngine oil
Clutch Linkage Pivot PointsAs requiredEngine oil
Floor Shift Linkage PointsAs requiredEngine oil
Hood Latch Assembly
a. Pivots and Spring Anchor
b. Release PawlAs requireda. Engine oil
b. Multipurpose type grease meeting require-
ments NLGI No. 1 or 2
Hood and door hinges
Fuel door hinge
Rear compartment lid hingesAs requiredEngine oil
WeatherstripsAs requiredSilicone grease

GENERAL INFORMATION 0B – 19
DAEWOO V–121 BL4
Manual Transaxle Identification Number
Plate (D16)
1. Identification Code
2. Sequential Number
Identification
Code
EngineGear Ratio
SY1.4L DOHC3.722 CR
CR1.6L DOHC3.722 CR
CV1.8L DOHC3.722 CR
Manual Transaxle Identification Number
Plate Location (D16)
The manual transaxle identification number is attached to
the top of the transmission case near the engine.
Automatic Transaxle Identification Number
Plate (ZF 4HP16)
1. Part Number
2. Sirial Number
3. Model Code
4. Manufactured Nation and Company
Part Code
Engine
AW1.8L DOHC
Automatic Transaxle Identification Number
Plate Location (ZF 4HP16)
The automatic transaxle identification number plate is at-
tached on the rear bottom side of the transaxle case near
the bulk head.