ad blue DODGE CHALLENGER 2014 3.G Owner's Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 2014, Model line: CHALLENGER, Model: DODGE CHALLENGER 2014 3.GPages: 539, PDF Size: 3.49 MB
Page 485 of 539

CavityCartridge Fuse Mini-Fuse Description
39 —10 Amp Red Heated Mirrors – If Equipped
40 —5 Amp Orange Auto Inside Rearview Mirror/Heated
Seats – If Equipped/Switch Bank
41 —— —
42 30 Amp Pink —Front Blower Motor
43 30 Amp Pink —Rear Window Defroster
44 20 Amp Blue —Amplifier/Sunroof – If Equipped
*Cavities 11, 12, and 13 contain self-resetting fuses (circuit
breakers) that are only serviceable by an authorized
dealer. The cluster and the driver seat switch are fused by
the 25 Amp circuit breaker in cavity 11. The passenger
seat switch is fused by the 25 Amp circuit breaker in
cavity 12. The door modules, the driver power window
switch, and the passenger power window switch are
fused by the 25 Amp circuit breaker in cavity 13. If you experience temporary or permanent loss of these sys-
tems, see your authorized dealer for service.
7
MAINTAINING YOUR VEHICLE 483
Page 488 of 539

this, you should not attempt to service a headlamp bulb
yourself. If a headlamp bulb fails, take your vehicle to
an authorized dealer for service.
WARNING!
A transient high voltage occurs at the bulb sockets of
HID headlamps when the headlamp switch is turned
ON. It may cause serious electrical shock or electro-
cution if not serviced properly. See your authorized
dealer for service.
NOTE: On vehicles equipped with HID headlamps,
when the headlamps are turned on, there is a blue hue to
the lamps. This diminishes and becomes more white after
approximately 10 seconds, as the system charges.
Front/Rear Side Marker Lamp
1. Remove the front/rear side marker. Use a fiber stick or similar tool to gently pry the lamp on the outboard
side to disengage the clip.
NOTE: If a screwdriver is used, make sure a soft material
is placed between the vehicle body and tool so not to
scratch the paint.
2. Rotate the bulb’s socket counterclockwise, and remove the bulb and socket assembly from the housing.
3. Pull the bulb out of the socket and insert the replace- ment bulb.
4. Install the bulb and socket assembly into the housing, and rotate the socket clockwise to lock it in place.
5. Reinstall the front/rear side marker.
486 MAINTAINING YOUR VEHICLE
Page 526 of 539

Hill Start Assist.......................... .329
Hitches Trailer Towing ........................ .384
HomeLink® (Garage Door Opener) ............185
Hood Release ........................... .159
Ignition .................................14
Key..................................12
Ignition Key Removal .......................14
Illuminated Entry ..........................22
Immobilizer (Sentry Key) ....................17
Infant Restraint ...........................73
Information Center, Vehicle ..................221
Inside Rearview Mirror .....................108
Instrument Cluster ....................... .209
Instrument Panel and Controls ................208
Instrument Panel Lens Cleaning ...............473
Integrated Power Module (Fuses) ..............475
Interior Appearance Care ....................472 Interior Lights
.......................... .167
Intermittent Wipers (Delay Wipers) .............169
Introduction ..............................4
iPod®/USB/MP3 Control Bluetooth® Streaming Audio ...............147
Jacking Instructions ....................... .416
Jack Location ........................... .413
Jack Operation .......................... .412
Jump Starting ........................... .421
Key Fob Arm The Alarm .........................20
Programming Additional Key Fobs ...........19
Programming Additional Transmitters .........19
Key-In Reminder ..........................16
Keyless Enter-N-Go ........................36
Keyless Entry System .......................23
Keyless Go ...............................12
524 INDEX