oil level DODGE MONACO 1965 1.G Owners Manual

z
o
-t-U 1&1 t-
O D: IL
4
HUW YOU CAN ENJOY· PROTECTION AND DRIVING SATISFACTIO
*
REQUIRED MAINTENANCE SERVICES
The following maintenance services ore required to assure full consideration under
the 5 year/50,OOO mile coverage of the Manufacturer's Passenger Car Warranty.
FIRST Oil CHANGE: The engine oil need not be removed until the flrst scheduled oil change .
WHEN TO ADD OIL: It's not unusual for a new engine to use a certain amount of engine oil during the break-in period. Check oil level during each stop for gasoline. Add oil only when level on dip stick is at or below the "ADD OIL" mark.
SELECTION OF O IL : Use only oils "For Service MS" and of the proper SAE grade for the overage temperature in your area. See Engine Oil Recommendations. poge 38.
SERVICE INTERVALS

Unusual Starting Conditions
Flooded En Int-Excessive "pumping" of the accelerator pedal may "flood" the engine,
causing a temporary no·start condition. A
strong odor of gasoline is an indication of a flooded engine. To start the engine under flooded conditions, depress the accelerator
pedal fully to the floor and hold there while
cranking untIl engine starts. Holding the accelerator fully to the floor opens the choke, allowing excess fuel to be eliminated from
the engine. Clearing the engine may take
about 10 seco'nds, depending on the amount
of excess fuel in the engine.
Extremely Cold Weather-When starting
your car at temperatures of zero or below,
depress the accelerator to the normal position
of one·third to one· half of Its full travel and crank the engine. Hold the key in the start
position until the engine is running. If the
engine attempts to start but does not, and the total engine cranking time required about 20 seconds, depress the accelerator all the
way to the floor until the engine starts run·
ning. If it does not start then return accelerator
to the one· third to one·half position and continue cranking. It may be necessary to repeat this procedure. NOTE: See "Recom·
mended Engine Oil Grades" and "If You Have an Automatic Transmission" in the
"Service Tips" section of this manual for recommendations regarding cold weather
starting. A larger capacity battery is available from your Dealer for use in extremely cold
areas.
BREAK·IN RECOMMENDATIONS-A
long break-in period is not required for your
new car. Drive moderately during the first 300 miles. After the initial 50 miles, speeds up to 50 or 60 mph are desirable. While cruising,
brief full·throttle accelerations contribute to a
good break·in (Within limits of state and local traffic laws). Wide· open throttle accelerations in low gear can be detrimental and should
be avoided for at least 500 miles. The oil installed in the engine at the factory is a high quality lubricant, classified "For
Service MS", and should be retained until
the first regular oil change. It is not unusual
for a new engine to use a certain amount of oil during this period. Have the oil level checked each time you stop for gasoline. If
oil is added, use only oils labeled on the con·
tainer "For Service MS" and of the weight required for the outside temperature, as
described on page 38.
11

(CONTINUlU)
CAUTION: To prevent possible wiring damage, certain precautions should be observed: It IS essential when replacing the cables on the battery, or when uSing a "booster" battery, thai the positive cable IS attached to the positive post and the negative cable IS attached to Ihe negative post. The negative cable IS attached to the engine block. Battery posts are marked plus (+ ) and minus (-). Also, If a "fast charger" is used while battery IS in car, disconnect both car battery cables before connecting the charger to battery. Do not use a "fast charger" to provide starting voltage.
which requires the following service attention. Two types are used -one has a wrapper on the carburetor air cleaner, and other does not. With Wrapper: Do the following every 6 months-inspect venhlator valve operation, clean filler cap, InSpect and clean air cleaner element and wash outer wrapper In kerosene and shake or blot dry. Every year-replace ventilator valve. Every two years-replace air cleaner element and wrapper. Without Wrapper: Do the follOWing at each change of engine Oil-inspect ventilator valve operation, Inspect and clean air cleaner element. Every year-replace ventilator valve and replace air cleaner element. More frequent servicing Crankcase Ventilation System. The engine in may be required if the car IS used for short. your car was equipped at the factory with a trip driving and prolonged engine idling. posItive ventilating system to reduce the emission of harmful fumes into the at mos· Ant/·Freele. So that your cooling system Will phere. Periodic and proper inspection and operate without freezing and Without over· cleaning of thiS valve is essential for good heating due to rust formation, the following engine performance and durability. Valve procedures should be observed. operation should be checked every 6 months O . . . by your Dealer, and more frequently if car IS Fall. Open ~adlator dralncock and remo~e used for short-trip driVing and prolonged threaded drain plugs In engine block to drain engine idling. Replace valve once a year. cooling system. Mov~ heat~r selector lever to ''HI'' or "Heat" position (If so eqUipped) to A special crankcase ventilation system is permit draining the heater lines. Thoroughly used on cars built for the state of California flush cooling system with clear water, then
36
close radiator draincock and replace engine block drain plugs. Install MoPar Anti·Freeze (or other high-quality equivalent) to assure cooling system protection for the lowest anticipated temperature in the area where vehicle IS operated dUring the winter months. The cooling system should contain a minimum of 400:, anll-freeze for proper corrosion protection. I n geographiC areas where anli· freeze protecllon IS not necessary, after flushing, fill with clear water and add MoPar Rust ReSistor (or other hlgh·quality co~rosion inhibitor) to prevent the formation of rust deposits. This service IS reqUired annually.
It the vehicle was placed into service after January I , 1965, the first required Fall cooling system service may be eliminated. With the approach of cool weather, however, it IS very important to test the coolant for adequate anti-freeze protection and InSpect the system for eVidence of rust or leaks.
Only glycols and synthetic alcohol (Methanol) are acceptable bases for automobile anti­freeze. Solutions containing salts, sugar, honey, glucose, mineral oils, kerosene or similar material should never be used in the cooling system.
@Coolant Level: Have the coolant level checked during each stop at the gasoline station. Add water to bring level to about I-~' below the bottom of the filler neck. Overfilling Will dilute the anti-freeze and also result In coolant loss through the overflow tube. CAUTION: DriVing in heavy traffic, at high altitudes, or In very hot weather may build up pressure in the cooling system. When removing the cap place a cloth over the cap, turn left to first stop, allowing steam to escape through overflow tube, then remove cap.

E) Coolant Level: Have the coolant level checked during each stop at the gasoline station. Add water to bring level to about 11,4' below the bottom of the filler neck. Overfilling will dilute the anti·freeze and also result in coolant loss through the overflow tube. CAUTION: Driving In heavy traffic, at high altitudes, or in very hot weather may build up pressure in the cooling system. When removing the cap place a cloth over the cap, turn left to first stop, allowing steam to escape through overflow tube, then remove cap.
Thermostat Your new car is equipped with 180 degree thermostat for use with perma· nenl-type anti-freeze. If you later prefer an lcohol type anti-freeze use only a 160 degree thormoslat.
Manifold Heal Control Valve_ A cold engine will warm up faster and accelerate more moothly if the valve that controls heat flow In the manifold works freely. It is normal for I d deposits to accumulate in time on the y lve shaft causing it to tighten up'. Manifold II t Control Valve Solvent, available from your dealer, should be applied a t six month lnt Iva Is. Slide shaft in and out and rotate a
, w times to distribute the solvent. Apply only when manifold is cool.
The Carburetor A ir Filter. The special easy to change fire-resistant filter installed in your carburetor should be cleaned and inspected every 6 months and replaced once every two years, to assure good fuel economy. Clean or replace more often when car is driven in dusty or sandy areas. Replace filter if dam­aged. DO NOT wash or oil. Simply remove the metal container, unscrew the wing nut and lift out filter. Clean with compressed air, holding nozzle about two inches from filter.
Fuel Filter. Your new car has a filter in the fuel tank to prevent water and foreign mate­rial from entering the fuel system. There is also a fuel filter in the fuel line at the fuel pump outlet. If this filter is plugged it can limit car speed and cause hard starling. Under normal operating conditions the filter should be changed at 20,000 mile intervals, or every two years.
011 Cap Filler. The cap on the oil filler tube is a combination ventilator and permanent filter. The filter inside the cap should be kept clean to allow clean air to remove combustion product s from the crankcase. To clean the filter wash the entire cap periodically in k ero ­sene and relubricate with SAE 30 engine oil.
ENGINE PERFORMANCE EVALUATION
Engine operation efficiency depends on cor­rect ignition, carburetor adjustments, and on valve lash where applicable. To obtain best engine performance, Chrysler Corporation recommends that the engine be evaluated every 10,000 miles and tuned, if necessary. Services performed during this evaluation should include the following:
SPARK PLUGS-Remove and inspect each spark plug. Most plugs can be cleaned, adjusted, and reinstalled. Rough idle, hard starling, frequent engine miss at high speeds, or apparent physical deterioration, are indica­tions that the spark plugs should be replaced.
DISTRIBUTOR-Clean and inspect the dis· tributor cap and rotor if required (wash cap in household detergent and water solution). Check breaker points for abnormal pitting. distributor secondary wires and tower caps are clean and connected properly. See that ignition timing is set to vehicle specifications.
CARBURETOR-Remove and clean air filter. Check operation of manifold heat control valve and choke diaphragms, use solvent recommended. Clean crankcase ventilator system. Check and adjust choke fast-idle cam and fuel mixture.
BATTERY-Check specific gravity. Clean and tighten terminals; apply grease to post and terminals. Check circuit voltages.
37

ENGINE OIL REQUIREMENTS
FIRST OIL CHANGE. The engine oil in­stalled in your car's engine at time of assem­bly is h igh quality, "For Service MS" oil and
need not be removed until the first scheduled
oil change_ "Break-in" or "Flush-type" oils are no longer required in you r car's advanced­
design engine and m ust be avoided.
WHEN TO ADD OIL It is not unusual for
a new engine to use a certain amount of engine oil during the break-in period. Check
oil level during each stop for gasoline. Add oil only when level on dipstick is al or below
the "ADD OIL" mark.
WHEN TO CHANGE OIL Regul.,. 011 changes .,.e required to provide proper engine operation.
Highway Driving, combined with some short
trip, slower speed operations extends the 38
effectiveness of the engine oil and permits you to change 011 at 4,000 miles Intervals.
Short Trips (less than 10 miles) and slow speeds, such as to the store, school, work
etc. and home again before the engine warms up, causes harmful condensation and sludge formation. This is typical of car operation in
city traffic. Driving under these conditions re­
quires that you change 011 every 3 months regardless of mileage.
Severe Operating Conditions, such as fre­
quent driving on dusty roads, or in sandy geographic areas, or unusually short trip
driving in cold weather may reasonably require 011 changes more frequently than
every three months. Under these conditions, consult and follow the advice of any Author­ized Chrysler Motors Corporation Dealer's
Service Manager.
Shaded area covers region where minimum tem­peratures are consistently below + 10"F. during
winter months.
RE MMENDED ENGINE OIL GRADE
Multigrade Oils: SAE 20W-40 Suitable when temperatures are co nsistently abovl! + 32°F. SAE 10W·30 Suitable year-round for most parts of the United States; may be used where temperatures occasionally drop as low as -10°F . SAE 5W·20 Recommended where minimu m temperatures are consistently below + 10°F . durin g winter months, see map. Low viscosity o ils make en~ine starting easier in cold weather. Modern SAE 5W-20 grade oils may be safely used when minimum temperatures are expected to be consistently below + 10°F. Single Grade Oils. SAE 30 When temperature ranges averag e co nsistently above 32°F . SAE lOW When temperature ranges average between + 32° F . and -10°F .

RAILER-TOWING SERVIICE RECOMMENDATIONS
II y"1I C r Is equipped with a factory-installed Trailer Towing package, provided the loaded trailer weight ,10.. not exceed 5,500 pounds and the car is serviced according to the recommendations shown below, ,II. M nufacture r's Passenger Car Warranty will apply. Otherwise, towing a loaded trailer weighing In I I of 2,500 pounds is viewed as abnormal use and service and the warranty does not apply.
I It IIIU' transmission fluid ........................... 32,000 miles initial and every 10,000 miles thereafter
"'111 H' Ir nsmissi on oil filter (auto . trans .) ......... 32,000 miles initial and every 10,000 miles thereafter
I It I" I' r r axle lubricant· ............................. , ............................ , ....... , .. 32,000 miles III P" I universal joints, splined transmission output "III, IIld check fluid level in transmission and rear axle ...... Every 2 months, not to exceed 4,000 miles
I I. 11111 nglne oil, , ........................... , .... Every 3 months (or 4,000 miles, whichever comes first)
I II 111' ngine oil filter ................ " .. " ..................................... Every second oil change
"' ( MMENDED SERVICE
III I"' I Iront brake assemblies and front wheel bearings ...... " ....... , .................. , , ,10,000 miles
'" "I I luel filter .......... " ... " ........... " .................. Every 20,000 miles (or once every 2 years) I .1 III IIr -Inspec t for wear ..................... , ...................................... Every 5,000 miles
I ""ittnllnation of the rear axle lubricant with water Is possible by submerging the rear axle in water, IlIlIwll, w ter to enter the axle vent. Boat-launching ramps are sometimes located to permit the 11111111 f Ion of the car axle . If contamination by water is evident or suspected, rear axle lubricant .,HI I II changed immediately, or early axle failure can result.
Hili Wh n towing a trailer tire pressures should be increased 4 psi on Sedan models and 6 psi on I tlon Wagon models.
"'d '1 0
~ n =I oo(
0 ~ 0 l!! '" ~ '" n '" 0 -c 0 0 m ~ z m 9
c::: ("t
< m c....., ::r: § t::l VJ n (1) Ol VJ r-~ ~ t-' m I:l'" (Xl .. \,0 t-' -t-'::: 0"1 C \,Ol!! 0"1 O"I~ m OlZ C Z '" .. -I !:l
'11
-n ,.
-f
-0
Z
39