DODGE RAM 1500 1998 2.G Workshop Manual

DODGE RAM 1500 1998 2.G Workshop Manual RAM 1500 1998 2.G DODGE DODGE https://www.carmanualsonline.info/img/12/5702/w960_5702-0.png DODGE RAM 1500 1998 2.G Workshop Manual
Trending: wheel, Washer, Ignition cylinder, Brake, ASD, EVAP Purge solenoid, Fuel pump replacement

Page 351 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual INSTALLATION
(1) Install fan blade assembly to electrically con-
trolled viscous fan drive. Tighten mounting bolts to
24 N´m (18 ft. lbs.) torque.
(2) Position the fan blade/viscous fan drive to the

Page 352 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual REMOVAL
(1) Disconnect the battery negative cable.
(2) Drain the coolant (Refer to 7 - COOLING -
STANDARD PROCEDURE).
(3) Remove the power cord from the heater by
unplugging (Fig. 7).
(4) Loosen (but

Page 353 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual OPERATION
The heater warms the engine coolant providing
easier engine starting and faster warm-up in low
temperatures. Connecting the power cord to a
grounded 110-120 volt AC electrical outlet with a

Page 354 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual REMOVAL
3.7L V-6
The Engine Coolant Temperature (ECT) sensor on
the 3.7L engine is installed into a water jacket at
front of intake manifold near rear of generator (Fig.
10).
WARNING: HOT, PRESSURIZED

Page 355 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual 5.9L Diesel
The Engine Coolant Temperature (ECT) sensor on
the 5.9L diesel engine is located near the thermostat
housing (Fig. 14).WARNING: HOT, PRESSURIZED COOLANT CAN
CAUSE INJURY BY SCALDING. COOLI

Page 356 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual INSTALLATION
3.7L V-6
(1) Apply thread sealant to sensor threads.
(2) Install sensor to engine.
(3) Tighten sensor to 11 N´m (8 ft. lbs.) torque.
(4) Connect electrical connector to sensor.
(5) Repla

Page 357 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual DIAGNOSIS AND TESTINGÐTHERMOSTAT
ON-BOARD DIAGNOSTICS
Allgasoline powered modelsare equipped with
On-Board Diagnostics for certain cooling system com-
ponents. Refer to On-Board Diagnostics (OBD) in

Page 358 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual CAUTION: A number or letter is stamped into the
tongue of the constant tension clamps (Fig. 19). If
replacement is necessary, use only an original
equipment clamp with a matching number, letter
and wi

Page 359 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual (7) Air Conditioned vehicles; Install the generator.
Tighten the bolts to 41 N´m (30 ft. lbs.).
(8) Install the support bracket (generator mount-
ing bracket-to-intake manifold). (Fig. 17). Tighten t

Page 360 of 2627

DODGE RAM 1500 1998 2.G Workshop Manual indicated by the instrument panel gauge or by poor
heater performance unless a DTC is present. Refer to
the Diagnosis section of this group for other probable
causes.
The DTC can also be accessed thro
Trending: Ignition system, Diagnosing no start, child restraint, Data link, Vacuum leak, ignition light, Transmission install