horn DODGE RAM 1999 Service Repair Manual
[x] Cancel search | Manufacturer: DODGE, Model Year: 1999, Model line: RAM, Model: DODGE RAM 1999Pages: 1691, PDF Size: 40.34 MB
Page 180 of 1691
CAUTION: When removing a deployed air bag, wear eye protection, rubber
gloves and a long-sleeve shirt. Powder residue from air bag
deployment may irritate skin and eyes.
CAUTION: Before removing steering wheel, position front wheels in
straight-ahead position and lock steering column by removing
ignition key. Failure to do so could damage clockspring or
cause clockspring to be off-centered. DO NOT hammer on
steering wheel during removal, or collapsible column could be
damaged.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM . Air bag module
is mounted on face of steering wheel. Ensure wheels are pointed
straight-ahead and steering wheel is locked.
2) Remove air bag module-to-steering wheel screws from back
side of steering wheel. Lift air bag module and disconnect electrical
connectors from rear of module.
Installation
Connect air bag, cruise control and horn harness connectors
to rear of air bag module. Secure module to steering wheel. Tighten
air bag module-to-steering wheel screws to specification. See
TORQUE SPECIFICATIONS . DO NOT connect negative battery cable at this
time. Go to SYSTEM OPERATION CHECK .
PASSENGER-SIDE AIR BAG MODULE
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
3) Remove 3 screws securing instrument panel glove box
opening upper trim strip to instrument panel glove box opening upper
reinforcement, then remove trim strip. Remove 4 screws that secure 2
plastic support brackets of passenger-side air bag door panel outlet
housing to glove box opening upper reinforcement.
4) Reach through and above glove box opening to access and
disconnect air bag module harness connector. Remove 2 screws securing
passenger-side air bag module front bracket to instrument panel
structural support. Remove 3 screws securing passenger-side air bag
module rear bracket to glove box opening upper reinforcement.
5) Using trim stick, gently pry passenger-side air bag door
(starting at lower left edge) away from instrument panel top cover.
Remove air bag module, air bag door and panel outlet housing and
barrel assembly from instrument panel as a unit.
Installation
To install, reverse removal procedure. Ensure air bag door is
securely attached to instrument panel. Ensure air bag harness
connector latches fully engaged. DO NOT connect negative battery cable
at this time. Go to SYSTEM OPERATION CHECK .
CLOCKSPRING
CAUTION: Failure to position wheels in the straight-ahead position
with steering wheel locked when removing steering wheel could
Page 181 of 1691
damage clockspring and/or require clockspring to be
readjusted.
NOTE: Clockspring is self-centering and will automatically lock in
the centered position when steering wheel is removed.
Adjustment is only required if centering position is
disturbed.
Removal
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) Clockspring is located behind steering wheel. See Fig. 1.
Ensure front wheels are in straight-ahead position. Lock steering
wheel. Remove air bag module. See AIR BAG MODULE.
3) Remove steering wheel nut. Using appropriate steering
wheel puller, remove steering wheel. When steering wheel is removed,
self-centering clockspring will automatically lock in place. Remove
upper and lower steering column shrouds to gain access to clockspring
wiring.
4) Remove knee bolster (if equipped). Disconnect Yellow 2-wa\
y
clockspring harness connector between clockspring and instrument panel
wiring harness, at base of steering column. See Fig. 13. Remove
clockspring by releasing 2 tabs on side of clockspring. Clockspring
cannot be repaired and must be replaced if faulty.
Installation
1) Snap clockspring onto steering column. If clockspring
centering adjustment is disturbed, adjust clockspring before
installing steering wheel. See CLOCKSPRING CENTERING under
ADJUSTMENTS. Connect clockspring wiring connectors. Install steering
column covers. Install knee bolster (if removed).
2) Position steering wheel on steering column. Ensure flats
on steering wheel hub fit formations on inside of clockspring. Pull
clockspring, cruise control switch (if equipped) and horn wires
through lower large holes and upper small holes in steering wheel.
3) Install steering wheel retaining nut and tighten to 45 ft.
lbs. (61 N.m). Connect horn and cruise control wires (if equipped).
Connect clockspring wire to air bag module. To ensure complete
connector connection, latching arms must be visible on top of
connector housing. DO NOT connect negative battery cable at this time.
Go to SYSTEM OPERATION CHECK .
PASSENGER AIR BAG DISARM (PAD) SWITCH
Removal & Installation
1) Before proceeding, see SERVICE PRECAUTIONS. Disable air
bag system. See DISABLING & ACTIVATING AIR BAG SYSTEM .
2) If vehicle is equipped with automatic transmission, turn
ignition switch to UNLOCK position, set parking brake and place
transmission selector lever in LOW position. Tilt steering column to
lowest position (if equipped). Using trim stick, gently pry around
perimeter of cluster bezel and remove bezel.
3) Open glove box. Holding glove box door, push center of
glove box bin towards front of vehicle. Flex glove box bin far enough
so glove box stops will clear sides of instrument panel opening. Roll
glove box down until stop bumpers are beyond sides of instrument panel
opening. Release bin. Lift bottom of glove box upward to disengage
hinge hooks form hinge pins.
4) Reach through glove box opening to access and disconnect 2
passenger-side air bag disarm switch harness connectors. Connectors
are attached to bracket located on inboard glove box opening
reinforcement. See Fig. 4. Remove 3 screws retaining passenger-side
air bag disarm switch bezel to instrument panel.
Page 183 of 1691
CLOCKSPRING CENTERING
CAUTION: If rotating part of clockspring is not positioned properly
with steering column and front wheels, clockspring failure
may result. The following procedure must be used to center
clockspring.
Depress 2 plastic auto-locking tabs. See Fig. 5. Keeping
auto-locking tabs depressed, rotate clockspring rotor clockwise to end
of its travel. DO NOT apply excessive force. Rotate rotor
counterclockwise 2 1/2 turns from end of travel and release auto-
locking tabs. Ensure horn wire ends up at the top and air bag module
wire at the bottom.
Fig. 5: Centering Clockspring
Courtesy of DaimlerChrysler Corp.
TORQUE SPECIFICATIONS
Page 211 of 1691
AN TI- T H EFT S YSTE M
1999 D odge P ic ku p R 1500
1999 ACCESSORIES & EQUIPMENT
CHRY - Anti-Theft Systems
Ram Pickup, Ram Van & Ram Wagon
DESCRIPTION
The Vehicle Theft Security System (VTSS) provides an engine
no-run feature, flashes headlights and sounds horn if any door or hood
is opened without using key or remote keyless entry transmitter, or if
battery cables are disconnected then reconnected when system is
activated.
Anti-theft system is controlled by Central Timer Module
(CTM). CTM is located under driver's side of dash panel, right of
steering column. If CTM is faulty, CTM cannot be repaired and must be
replaced.
VTSS is also equipped with a power-up mode. If battery is
disconnected or looses power while VTSS is armed, VTSS system remains
armed when power is restored. A temper alert signal is sounded on
vehicle entry if VTSS was triggered while away from vehicle. Horn will
sound 3 times alerting owner VTSS was triggered.
OPERATION
ARMING PROCEDURE (PASSIVE)
Remove key from ignition. Ensure headlights are off. Lock
doors while open, using power lock switch. Power lock switch will not
operate with key in ignition or headlights on while door is open.
Vehicle Theft Security System (VTSS) will not arm using key in lock
cylinder or mechanical lock button. While system is arming, SECURITY
light will flash rapidly for 15 seconds. Opening any door or turning
the ignition key while light is flashing will abort arming process.
Once arming process is complete, SECURITY light will go out.
ARMING PROCEDURE (ACTIVE)
Pressing Remote Keyless Entry (RKE) transmitter LOCK button
will actively arm Vehicle Theft Security System (VTSS). All doors must\
be closed and ignition switch in OFF position. While system is arming,
SECURITY light will flash rapidly for 15 seconds. Opening any door or
turning the ignition key while light is flashing will abort arming
process. Once arming process is complete, SECURITY light will go out.
DISARMING
Vehicle Theft Security System (VTSS) can be disarmed 2 ways:
unlock vehicle using key in any door and pressing remote keyless entry
transmitter UNLOCK button. If alarm has been set off, either method
can be used to disarm and shut-off horn.
CENTRAL TIMER MODULE (CTM)
Central Timer Module (CTM) is Vehicle Theft Security System
(VTSS) processor. CTM uses the data bus network to allow sharing and
reporting of sensor information. If a door ajar sensor is opened while
VTSS is set, a signal is sent to flash headlights and sound horn. PCM
is also notified through bus network to enable engine no-run feature.
Page 212 of 1691
CTM has remote keyless entry receiver and control logic incorporated.
COMPONENT TESTS
RELAYS
NOTE: Headlight relay may also be referred to as the security
relay. On Ram Pickup, the headlight relay is located in Power
Distribution Center (PDC) in engine compartment. On Ram Van
and Ram Wagon, the headlight relay is taped to headlight
switch harness. On Ram Pickup, the horn relay is located in
Power Distribution Center (PDC) in engine compartment. On Ram\
Van and Ram Wagon, the horn relay is located in junction
block under left side of instrument panel. For circuit
testing, see WIRING DIAGRAMS.
Headlight Relay & Horn Relay
Remove relay to be tested. Measure resistance between
appropriate relay terminals with relay de-energized and energized. See
RELAY TEST SPECIFICATIONS table. See Fig. 1. If continuity or
resistance is not as specified, replace relay.
RELAY TEST SPECIFICATIONS
\
\
\
\
\
\
\
Terminals Condition
De-Energized
87A & 30 .............................................. Continuity
87 & 30 ............................................ No Continuity
85 & 86 .................................... 70-80 Ohms Resistance
Energized ( 1)
87 & 30 ............................................... Continuity
87A & 30 ........................................... No Continuity
( 1) - Apply position battery voltage to terminal No. 85 and ground
terminal No. 86.
\
\
\
\
\
\
\
Fig. 1: Identifying Relay Connector Terminals
Courtesy of Chrysler Corp.
SYSTEM TESTS
Page 313 of 1691
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Clear trouble codes as needed. See BODY CONTROL COMPUTER -
INTRODUCTION article. Using scan tool, read I/O's door unlock switch
status. If scan tool displays RELEASED, system is currently
functioning properly. If scan tool does not display RELEASED, go to
next step.
2) Disconnect left door lock switch connector. If scan tool
displays RELEASED, replace left door lock switch. If scan tool does
not display RELEASED, go to next step.
3) Disconnect right door lock switch connector. If scan tool
displays RELEASED, replace right door lock switch. If scan tool does
not display RELEASED, go to next step.
4) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Disconnect CTM 18-pin connector C2.
Using an external voltmeter, measure voltage between ground and CTM
18-pin connector C2 terminal No. 4 (Orange/Dark Green wire). If
voltage is more than 1.5 volts, repair short to voltage in Orange/Dark
Green wire between CTM and door lock switch. If voltage is 1.5 volts
or less, replace CTM.
IDENTIFYING VTSS PROBLEMS
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool, select BODY SYSTEM then VTSS and read
Central Timer Module (CTM) DTCs. If any VTSS DTCs are displayed,
perform appropriate procedure. See VTSS DTC table. If no VTSS DTCs are
displayed, go to next step.
VTSS DTC
\
\
\
\
\
\
\
DTC Message Perform
DOOR DISARM SWITCH FAILURE .............. DOOR DISARM SWITCH FAILURE
DOOR LOCK SWITCH FAILURE .................. DOOR LOCK SWITCH FAILURE
DOOR UNLOCK SWITCH FAILURE .............. DOOR UNLOCK SWITCH FAILURE
EEPROM CHECKSUM FAILURE ................................ Replace CTM
INTERNAL ROM TEST FAILURE .............................. Replace CTM
\
\
\
\
\
\
\
2) Select VTSS then MONITORS. If scan tool displays, OK TO
RUN, NOT OK TO ARM, PCM has not recorded more than 20 starts. Start
engine 20 times and retest. If message does not change to OK TO ARM,
replace PCM. If scan tool displays NO RESPONSE TO PCM, see appropriate
VEHICLE COMMUNICATIONS article. If scan tool does not display OK TO
RUN, NOT OK TO ARM or NO RESPONSE TO PCM, go to next step.
3) Using scan tool, actuate horn, headlights and VTSS light
to flash. If horn does not sound, go to next step. If headlights do
not flash, go to step 6). If VTSS light does not flash, go to step 9).\
If all function properly, go to step 12).
4) Press horn button. If horn does not sound, go to
appropriate STEERING COLUMN SWITCHES article. If horn sounds, go to
next step.
5) Locate Central Timer Module (CTM). CTM is located behind
Page 314 of 1691
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external voltmeter, measure voltage between ground and
CTM 18-pin connector C2 terminal No. 18 (Black/Red wire). If voltage
is more than 9.5 volts, replace CTM. If voltage is 9.5 volts or less,
repair open in Black/Red wire between CTM and horn relay.
6) Remove security relay from Power Distribution Center
(PDC). Turn ignition on. Connect a test light between battery source
and headlight relay connector terminal No. 85 (Red/Dark Blue wire).
Using scan tool, actuate relay. If test light illuminates, replace
security relay. If test light does not illuminate, go to next step.
7) Using an external voltmeter, measure voltage between
battery voltage and security relay connector terminal No. 86
(Red/Orange wire). If voltage is more than 9.5 volts, go to next step.\
If voltage is 9.5 volts or less, repair open in Red/Orange wire
between battery source and security relay.
8) Reinstall security relay. Locate Central Timer Module
(CTM). CTM is located behind right kick panel. Disconnect CTM 18-pin
connector C2. Using an external voltmeter, measure voltage between
ground and CTM 18-pin connector C2 terminal No. 6 (Red/Dark Blue
wire). If voltage is more than 9.5 volts, replace CTM. If voltage is
9.5 volts or less, repair open in Red/Dark Blue wire between CTM and
security relay.
9) Disconnect overhead console 12-pin connector. Using an
external voltmeter, measure voltage between battery and overhead
console 12-pin connector terminal No. 11 (Black wire). Using scan
tool, actuate VTSS indicator light. If voltage is about 10 volts,
replace overhead console. If voltage is not about 10 volts, go to next
step.
10) Measure voltage between ground and overhead console 12-
pin connector terminal No. 5 (Pink wire). Turn ignition on. If voltage\
is more than 10 volts, go to next step. If voltage is 10 volts or
less, repair open Pink wire.
11) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 18-pin connector C2. Turn ignition
on. Using an external ohmmeter, measure resistance between ground and
CTM 18-pin connector C2 terminal No. 8 (Black wire). If resistance is
5 ohms or more, replace CTM. If resistance is less than 5 ohms, repair
open Black wire between CTM and VTSS indicator light.
12) Using scan tool, place VTSS in diagnostic mode and follow
directions on screen. If TURN KEY TO ACC POSITION is not displayed, go
to step 24). If NO RESPONSE after turning key to accessory position or
TURN KEY TO ACC POSITION is displayed longer than 15 seconds, go to
next step. If neither response is received, go to step 14).
13) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Gain access to CTM 18-pin connector C2. Ensure key
is in accessory position. Using an external voltmeter, measure voltage
between ground and backprobe of CTM 18-pin connector C2 terminal No. 5
(Dark Blue/White wire). If voltage is more than 10 volts, replace CTM.\
If voltage is 10 volts or less, repair open Dark Blue/White wire
between CTM and junction block.
14) Remove key from ignition. Wait 2 seconds after performing
each of the following actions. Open, then close both door. Operate
power door lock switch to lock, then unlock position. Rotate key both
directions in both doors. Ensure each operation is successful. If any
operation is unsuccessful, see VTSS SYMPTOM DIRECTORY table for repair
of failed operation. If all operations are successful, go to step 22).
VTSS SYMPTOM DIRECTORY
\
\
\
\
\
\
\
Problem Circuit Go To
Driver's Door Open Or Close ............................... Step 15)
Page 316 of 1691
disarm switch state CLOSED, replace CTM.
23) Turn ignition switch to START position. If horn does not
sound, go to next step. If horn sounds, go to step 24).
24) Locate Central Timer Module (CTM). CTM is located behind\
right kick panel. Disconnect CTM 14-pin connector C1. Using an
external voltmeter, measure voltage between ground and CTM 14-pin
connector C1 terminal No. 8 (Dark Blue/White wire). If voltage is more\
than 10 volts, replace CTM. If voltage is 10 volts or less, repair
open Dark Blue/White wire between CTM and RUN-ACC fuse in junction
block.
WINDSHIELD WIPER SYSTEM
WIPER PARK SWITCH FAILURE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
NOTE: It takes 8 seconds for wiper park switch failure DTC to set.
1) Using scan tool, clear DTCs. See appropriate SELF-
DIAGNOSTICS article. Operate wipers in low speed, then intermittent
mode. Reread DTCs. If WIPER PARK SWITCH FAILURE is displayed, go to
next step. If WIPER PARK SWITCH FAILURE is not displayed, system is
currently functioning properly.
2) Gain access to wiper motor connector. Using an external
voltmeter, measure voltage between ground and wiper motor terminal No.
2 (Dark Green wire). If voltage is more than 9 volts, go to next step.\
If voltage is 9 volts or less, replace wiper motor.
3) Locate Central Timer Module (CTM). CTM is located under
left side of instrument panel. Using an external voltmeter, measure
voltage between ground and backprobe of CTM 14-pin Green connector C1
terminal No. 11 (Dark Green wire). If voltage is 9 volts or less,
replace CTM. If voltage is more than 9 volts, repair short to voltage
in Dark Green wire between CTM and wiper relay or wiper motor.
INTERMITTENT WIPERS INOPERATIVE
NOTE: For connector terminal identification and wiring diagrams,
see BODY CONTROL COMPUTER - INTRODUCTION article. Perform
VERIFICATION TEST VER-1A after each repair.
CAUTION: Always turn ignition switch to OFF position prior to
disconnecting or connecting any module connector.
1) Using scan tool select CENTRAL TIMER MODULE. If scan tool
displays NO RESPONSE, go to appropriate VEHICLE COMMUNICATIONS
article. If scan tool displays any CCD bus failure message, go to
SYMPTOM IDENTIFICATION. If scan tool does not display NO RESPONSE or
any CCD bus failure message, go to next step.
2) If problem is wipers parking in wrong position, go to next
step. If problem is not wipers parking in wrong position, go to step
5).
3) Gain access to wiper motor connector. Turn wipers on to
low speed. Using an external voltmeter, measure voltage between ground
and wiper motor switch terminal No. 2 (Dark Green wire). If voltage
does not cycle between zero and 12 volts, replace wiper motor. If
voltage cycles between zero and 12 volts, go to next step.
Page 402 of 1691
Fully depress brake pedal and rotate brake switch
counterclockwise approximately 30 degrees. Remove brake switch from
bracket. Depress lock tabs holding brake switch mounting bracket and
separate harness connector from brake switch.
Installation
1) Before installing brake switch, reset adjustable plunger
by pulling on plunger head until plunger reaches end of travel.
Connect harness connector to brake switch. Depress brake pedal and
insert brake switch into keyed hole in mounting bracket. Rotate brake
switch clockwise into locked position.
2) Gently pull back on brake pedal until pedal will go no
further. This causes the brake switch plunger to ratchet backward to
the correct position. No further adjustment is required.
SPEED CONTROL SERVO
Removal (Except Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Disconnect electrical
connector and vacuum hose from servo. Using finger pressure only, push
servo cable connector from throttle body bellcrank pin. DO NOT pull
cable connector perpendicular to bellcrank.
2) Remove 2 servo cable mounting nuts. Pull servo cable
sleeve away from mounting bracket to expose cable retaining clip.
Remove retaining clip. Remove servo.
Removal (Ram Van & Ram Wagon)
1) Disconnect negative battery cable. Remove engine cover.
Remove air cleaner assembly. Using finger pressure only, push servo
cable connector from throttle body bellcrank pin. DO NOT pull cable
connector perpendicular to bellcrank.
2) Remove right headlight assembly. Disconnect vacuum hose
and electrical connector at servo. Remove 2 servo mounting bracket
bolts. Remove 2 servo cable mounting nuts. Pull servo cable sleeve
away from mounting bracket to expose cable retaining clip. Remove
retaining clip. Remove servo.
Installation (All Models)
With throttle in full open position, align hole in speed
control cable sleeve with hole in servo pin. Install retaining clip.
To complete installation, reverse removal procedure. Tighten mounting
bolts/nuts to 75 INCH lbs. (8.5 N.m).
SPEED CONTROL SWITCHES
Removal & Installation
Turn ignition off. Disconnect negative battery cable. Wait 2
minutes for air bag system to discharge reserve voltage. Remove 2
screws holding air bag assembly to steering column. Separate air bag
assembly from steering column and disconnect air bag, horn and speed
control switch connectors. Remove screws securing speed control switch
to air bag assembly. Separate speed control switch from air bag
assembly. To install, reverse removal procedure.
WIRING DIAGRAMS
Page 511 of 1691
ELE C TR IC AL C O M PO NEN T L O CATO R
1999 D odge P ic ku p R 1500
1999 ELECTRICAL COMPONENT LOCATION
Chrysler Motors Electrical Component Location
Dodge; Ram Pickup
SAFETY PRECAUTION
WARNING: When working on vehicles equipped with Supplemental Restraint
System (SRS), never apply electrical voltage to the system.
This could cause the SRS (air bag) to be deployed.
BUZZERS, RELAYS & TIMERS
\
\
\
\
\
\
\
Component Component Location \
\
\
\
\
\
\
A/C Compressor Clutch Relay On power distribution center.
Automatic Shut Down Relay On power distribution center.
Blower Motor Relay On power distribution center.
Central Timer Module Left side of dash, inboard of
steering column opening.
Combination Flasher Left side of dash, on
junction block.
Engine Starter Motor Relay On power distribution center.
Fog Lamp Relay On power distribution center.
Fuel Heater Relay (Diesel) On power distribution center.
Fuel Pump Relay On power distribution center.
Horn Relay On power distribution center.
Intake Air Heater Relay No. 1
(Diesel) On left inner fender, below
left battery.
Intake Air Heater Relay No. 2
(Diesel) On left inner fender, below
left battery.
Quad High Beam Relay On power distribution center.
Radio Choke Relay Behind center of dash, on
support.
Security Relay On power distribution center.
Trailer Tow Relay On power distribution center.
Transmission Control Relay On power distribution center.
Wiper Motor Relay On power distribution center.
\
\
\
\
\
\
\