coolant reservoir DODGE RAM 2001 Service Owner's Manual

(8) Install the fan support/hub assy. (Fig. 180) and
tighten bolts to 24 N´m (18 ft. lbs.) torque.
(9) Install the accessory drive belt (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
INSTALLATION).
(10) Install the cooling fan and shroud together
(Refer to 7 - COOLING/ENGINE/RADIATOR FAN -
INSTALLATION).
(11) Install the windshield washer reservoir to the
fan shroud and connect the washer pump supply
hose and electrical connection.(12) Install the coolant recovery bottle to the fan
shroud and connect the hose to the radiator filler
neck.
(13) Install the radiator upper hose and clamps.
(14) Add coolant (Refer to 7 - COOLING - STAN-
DARD PROCEDURE).
(15) Connect the battery cables.
(16) Start engine and inspect for leaks.
9 - 308 ENGINE 5.9L DIESELBR/BE
GEAR HOUSING COVER (Continued)

(8) Fill the system with fluid and perform Steering
Pump Initial Operation, (Refer to 19 - STEERING/
PUMP - STANDARD PROCEDURE).
(9) Start the engine and run it for fifteen minutes
then stop the engine.
(10) Remove the return line/lines from the pump
and plug the pump port/ports.
(11) Pour fresh fluid into the reservoir and check
the draining fluid for contamination. If the fluid is
still contaminated, disassemble and clean the steer-
ing gear and flush the system again.
(12) Install the return line/lines and perform
Steering Pump Initial Operation, (Refer to 19 -
STEERING/PUMP - STANDARD PROCEDURE).
REMOVAL - GASOLINE ENGINE
(1) Remove the serpentine drive belt, (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
REMOVAL) OR (Refer to 7 - COOLING/ACCESSORY
DRIVE/DRIVE BELTS - REMOVAL).
(2) Remove the hoses from the power steering
pump and cap the fittings.
(3) Remove battery ground cable and unthread
stud from cylinder head, do not remove from bracket.
(4) Loosen upper bracket bolt and remove the
lower bracket to engine block bolts.
(5) Pivot the pump assembly past the coolant tube.
(6) Remove the upper stud and remove upper bolt
from cylinder head.
(7) Remove steering pump and mounting bracket
from engine as an assembly.
(8) Remove the pump pulley with Puller C-4333, to
access pump attaching bolts, (Refer to 19 - STEER-
ING/PUMP/PULLEY - REMOVAL).
(9) Remove the front pump bracket (Fig. 3). On
8.0L engine remove rear pump bracket (Fig. 4).
REMOVAL - DIESEL ENGINE
(1) Remove and cap steering pump hoses and vac-
uum pump vacuum line.
(2) Remove the sender unit from engine block and
plug hole in block (Fig. 5).
(3) Remove the serpentine belt, (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
REMOVAL).
(4) Remove and cap the oil feed line from the bot-
tom of the vacuum pump (Fig. 6).
(5) Remove the lower bolt that attaches the vacu-
um/steering pump assembly to the engine block.
Remove the nut from the steering pump attaching
bracket (Fig. 6).
(6) Remove upper bolt from the pump assembly
(Fig. 7) and remove the assembly.
(7) Remove the mounting gasket.
(8) Remove the steering pump to vacuum pump
bracket attaching nuts (Fig. 8).
Fig. 3 Pump Mounting 8.0L
1 - FRONT BRACKET
2 - REAR BRACKET
3 - STEERING PUMP
4 - PULLEY
Fig. 4 Pump Mounting 8.0L
1 - FRONT BRACKET
2 - REAR BRACKET
3 - STEERING PUMP
4 - PULLEY
BR/BEPUMP 19 - 33
PUMP (Continued)

(9) Slide the steering pump from the bracket. Use
care not to damage the internal oil seal in the vac-
uum pump (Fig. 9).
(10) Remove the two pump body spacers.
INSTALLATION - GASOLINE ENGINE
(1) Install the front pump bracket and tighten
bolts to 47 N´m (35 ft. lbs.). On 8.0L engine install
rear pump bracket and tighten nut to 47 N´m (35 ft.
lbs.), tighten bolts to 24 N´m (18 ft. lbs.).
(2) Install the pump pulley with Installer
C-4063±B, (Refer to 19 - STEERING/PUMP/PULLEY
- INSTALLATION).
(3) Install steering pump assembly on the engine
block. Install the upper stud and bolt in bracket.
(4) Pivot the pump down past the coolant tube and
install the lower bolts in bracket.(5) Tighten the bolts and nut to 41 N´m (30 ft.
lbs.).
(6) Connect the hoses to the pump.
(7) Install the serpentine drive belt, (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
INSTALLATION), (Refer to 7 - COOLING/ACCES-
SORY DRIVE/DRIVE BELTS - INSTALLATION).
(8) Fill the reservoir with power steering fluid,
(Refer to 19 - STEERING/PUMP - STANDARD PRO-
CEDURE).
INSTALLATION - DIESEL ENGINE
(1) Install the two pump body spacers.
(2) Rotate the drive gear until the steering pump
and vacuum pump drive dogs align. Install the steer-
ing pump onto the vacuum pump bracket. Use care
to avoid damaging the oil seal in the vacuum pump
during installation.The steering pump housing
and spacers must mate completely with the
vacuum pump bracket.
(3) Install the vacuum pump bracket to steering
pump nuts and tighten to 24 N´m (18 ft. lbs.).
(4) Position new gasket on vacuum pump assem-
bly. Use sealer if necessary to retain the gasket.
(5) Align and install the pump assembly on the
engine. Ensure the steering pump stud is inserted
into the block bracket. Tighten the pump- to-engine
block attaching bolts to 77 N´m (57 ft. lbs.).
(6) Install the steering pump to attaching bracket
nut and tighten to 24 N´m (18 ft. lbs.).
(7) Remove plug and install the oil pressure send-
ing unit and electrical connector.
(8) Install the oil feed line to the vacuum pump.
Tighten the oil line connection to 7 N´m (60 in. lbs./ 5
ft. lbs.).
(9) Install the fluid hoses to the power steering
pump. Tighten the pressure fitting at the pump to 31
N´m (23 ft. lbs.).
(10) Install and clamp the hose on the vacuum
pump.
(11) Install the serpentine belt, (Refer to 7 -
COOLING/ACCESSORY DRIVE/DRIVE BELTS -
INSTALLATION).
(12) Fill the reservoir with power steering fluid,
(Refer to 19 - STEERING/PUMP - STANDARD PRO-
CEDURE).
(13) Start the engine and check the operation of
the brakes.
Fig. 9 Steering Pump & Vacuum Pump
1 - PUMP SHAFT
2 - VACUUM FITTING
3 - VACUUM PUMP DRIVE
4 - OIL SEAL
5 - MOUNTING BRACKET
6 - DRIVE DOG
7 - PUMP SPACERS
BR/BEPUMP 19 - 35
PUMP (Continued)

(2) Remove air cleaner from wheelhouse (DIESEL
ONLY).
(3) Remove coolant overflow bottle (V-10 ONLY).
(4) Remove battery tray (Refer to 8 - ELECTRI-
CAL/BATTERY SYSTEM/TRAY - REMOVAL).
(5) Remove screws attaching power distribution
center to left wheelhouse (Fig. 14).
(6) Disengage wire harness tie-downs from wheel-
house.
(7) Disconnect wiring harness to headlamp connec-
tor.
(8) Disconnect wiring harness to airbag sensor and
remove airbag sensor from wheelhouse.
(9) Remove bolts attaching anti-lock brake control-
ler to wheelhouse (Fig. 14), if equipped.
(10) Disengage windshield washer tubing tie-
downs from wheelhouse (Fig. 14).
(11) Remove bolts attaching front fender to cowl
reinforcement (Fig. 15).
(12) Remove bolts attaching front fender to radia-
tor closure panel (Fig. 16).
(13) Remove bolts attaching bottom of front fender
to rocker panel lower flange.
(14) Open left door.
(15) Remove bolt attaching front fender to hinge
pillar mounting bracket.
(16) Remove bolts attaching top of fender to radia-
tor closure panel.
(17) Separate left front fender from vehicle.
INSTALLATION
(1) Position left front fender on vehicle.
(2) Install bolts attaching top of fender to radiator
closure panel.
(3) Install bolt attaching front fender to hinge pil-
lar mounting bracket.
(4) Install bolts attaching bottom of front fender to
rocker panel lower flange.
(5) Install bolts attaching front fender to radiator
closure panel.
(6) Install bolts attaching front fender to cowl rein-
forcement.
(7) Secure windshield washer tubing tie-downs to
wheelhouse.
(8) Install anti-lock brake controller to wheel-
house, if equipped.
(9) Install airbag sensor to wheelhouse and con-
nect wiring harness to airbag sensor.
(10) Connect wiring harness to headlamp connec-
tor.
(11) Secure wire harness tie-downs to wheelhouse.
(12) Install power distribution center to wheel-
house.
(13) Install battery tray (Refer to 8 - ELECTRI-
CAL/BATTERY SYSTEM/TRAY - INSTALLATION).
(14) Install coolant overflow bottle (V-10 ONLY).
Fig. 14 Left Front Fender Access Components
1 - ABS CONTROLLER
2 - POWER DISTRIBUTION CENTER
3 - BATTERY
4 - FENDER
5 - WINDSHIELD WASHER RESERVOIR
6 - BRAKE MASTER CYLINDER
Fig. 15 Fender to Cowl ReinforcementÐTypical
1 - BOLT
2 - FENDER
3 - FENDERÐTOÐCOWL REINFORCEMENT
BR/BEEXTERIOR 23 - 93
LEFT FRONT FENDER (Continued)

BRAKE MASTER CYLINDER
CAUTION: Only use fluid that meets specified
requirements (DOT 3).
NOTE: Wipe the master cylinder cover to remove
any dirt.
NOTE: On vehicles equipped with remote antilock
brakes, the fluid level check is the same as for a
normal system.
Check the brake master cylinder fluid level (Fig.
4). Add fluid to bring the level to the full line on the
side of the reservoir (or above the bottom of the split
ring in the primary filler hole). Be sure both primary
and secondary cavities are full to the maximum level
as indicated.
POWER STEERING RESERVOIR
CAUTION: Only use fluid that meets specified
requirements. Petroleum fluids, such as Mopar
Power Steering Fluid, are specially formulated for
use with power steering hoses and seals.
Check the fluid level; it should be maintained at
the proper level indicated on the dipstick, or as
viewed through the translucent reservoir. If fluid is
required, fill to the proper level. With the engine run-
ning at normal operating temperature, turn the
steering wheel from stop to stop to expel air fromwithin the system Stop the engine, remove the cap,
and recheck the fluid level, making sure that foam-
ing is not present (Fig. 5).
WINDSHIELD WASHER RESERVOIR
CAUTION: Do not add engine coolant (antifreeze) to
this reservoir.
CAUTION: Avoid spilling washer solvent on the
vehicles paint; it could harm the finish.
Fig. 4 BRAKE MASTER CYLINDER FLUID RESERVOIR
Fig. 5 POWER STEERING RESERVOIR
Fig. 6 WINDSHIELD WASHER FLUID RESERVOIR
BR/BENEW VEHICLE PREPARATION 30 - 5
UNDER HOOD (Continued)

Check windshield washer solvent reservoir and fill
as necessary (Fig. 6).
NOTE: When using concentrated solvent such as
MoparTAll-Weather Windshield Washer Solution,
dilute per container directions.
COOLING SYSTEM RESERVOIR
WARNING: DO NOT REMOVE RADIATOR CAP
WHILE COOLING SYSTEM IS UNDER PRESSURE.
NOTE: Add coolant only to plastic reserve tank if it is
required. Engine must be at normal operating temper-
ature before adding coolant to reserve tank. In cold
climates, coolant in reserve tank may appear low; do
not add coolant until normal temperature is reached.
Check coolant level with engine idling at normal
operating temperature. Coolant level in plastic
reserve tank must be between the minimum and
maximun marks (Fig. 7).
If coolant is added, use a 50/50 (-309F protection) con-
centration of the recommended (Refer to the Service
Information for specificate Mopartantifreeze recom-
mendation ) antifreeze and distilled water. Use a
higher concentration (up to 65%) if a lower freeze point
is required. Do not use recycled coolant in new vehicles.
INSPECTION - LINES/HOSES
Inspect the following for line and hose leaks. Also
inspect routing and connections and reroute and
tighten as required.²Brake Lines (Fig. 8)
²Fuel Lines (Fig. 9)
²Power Steering Hoses
²Vacuum Hoses
²Heating/Coolant Hoses
²Clutch Lines
²Refrigerant Lines
²Transmission oil cooler lines (Fig. 10)
Fig. 7 ENGINE COOLANT RESERVOIRFig. 8 PARKING BRAKE CABLE AND BRAKE LINE
Fig. 9 BRAKE LINES AND FUEL LINES
1 - FUEL LINE
2 - BRAKE LINE
30 - 6 NEW VEHICLE PREPARATIONBR/BE
UNDER HOOD (Continued)

FAN - 3.9L/5.2L/5.9L/8.0L -
INSTALLATION, RADIATOR..............7-43
FAN - 3.9L/5.2L/5.9L/8.0L - REMOVAL,
RADIATOR...........................7-42
FAN - 5.9L DIESEL - CLEANING,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSPECTION,
RADIATOR...........................7-44
FAN - 5.9L DIESEL - INSTALLATION,
RADIATOR...........................7-45
FAN - 5.9L DIESEL - REMOVAL,
RADIATOR...........................7-44
FAN DRIVE - DIAGNOSIS AND TESTING,
VISCOUS........................7-56,7-58
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - DESCRIPTION.......7-56
FAN DRIVE VISCOUS CLUTCH -
3.9L/5.2L/5.9L/8.0L - OPERATION.........7-56
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - DESCRIPTION................7-57
FAN DRIVE VISCOUS CLUTCH - 5.9L
DIESEL - OPERATION..................7-57
FASCIA - ADJUSTMENT, FRONT..........13-2
FASCIA - INSTALLATION, FRONT.........13-2
FASCIA - INSTALLATION, FRONT LOWER . . . 13-3
FASCIA - REMOVAL, FRONT.............13-2
FASCIA - REMOVAL, FRONT LOWER......13-3
FASCIA-SPORT - INSTALLATION, FRONT . . . 13-3
FASCIA-SPORT - REMOVAL, FRONT.......13-3
FASTENER IDENTIFICATION -
DESCRIPTION......................Intro.-3
FASTENER USAGE - DESCRIPTION......Intro.-6
FASTENERS - DESCRIPTION, PUSH-IN.....23-1
FEATURES - DESCRIPTION,
PROGRAMMABLE ELECTRONIC.........30-20
FEATURES - OPERATION,
PROGRAMMABLE ELECTRONIC.........30-20
FENDER - INSTALLATION, LEFT FRONT . . . 23-93
FENDER - INSTALLATION, REAR.........23-95
FENDER - INSTALLATION, RIGHT FRONT . . 23-94
FENDER - REMOVAL, LEFT FRONT.......23-92
FENDER - REMOVAL, REAR............23-95
FENDER - REMOVAL, RIGHT FRONT......23-94
FILL - STANDARD PROCEDURE,
TRANSMISSION . . . 21-201,21-372,21-547,21-718
FILL DOOR - INSTALLATION, FUEL.......23-95
FILL DOOR - REMOVAL, FUEL..........23-95
FILLER CAP - DESCRIPTION, FUEL.......25-33
FILLER CAP - OPERATION, FUEL........25-33
FILLER CAP - REMOVAL/INSTALLATION,
FUEL..............................25-33
FILTER - DESCRIPTION, PCV...........25-35
FILTER - INSTALLATION, AIR PUMP......25-29
FILTER - INSTALLATION, INLET..........14-22
FILTER - INSTALLATION, OIL . 9-105,9-161,9-218,
9-296,9-48
FILTER - REMOVAL, AIR PUMP.........25-29
FILTER - REMOVAL, INLET.............14-22
FILTER - REMOVAL, OIL.....9-105,9-161,9-218,
9-296,9-48
FILTER - STANDARD PROCEDURES,
WATER DRAINING AT FUEL............14-56
FILTER / WATER SEPARATOR -
DESCRIPTION, FUEL..................14-59
FILTER / WATER SEPARATOR -
INSTALLATION, FUEL.................14-61
FILTER / WATER SEPARATOR -
OPERATION, FUEL....................14-59
FILTER / WATER SEPARATOR -
REMOVAL, FUEL.....................14-60
FILTER REPLACEMENT - STANDARD
PROCEDURE, FLUID.....21-201,21-372,21-547,
21-717
FILTER/PRESSURE REGULATOR -
DESCRIPTION, FUEL...................14-5
FILTER/PRESSURE REGULATOR -
INSTALLATION, FUEL..................14-6
FILTER/PRESSURE REGULATOR -
OPERATION, FUEL.....................14-5
FILTER/PRESSURE REGULATOR -
REMOVAL, FUEL
......................14-5
FINAL STEPS - NEW VEHICLE
PREPARATION FORM
.................30-22
FINISH - DESCRIPTION, BASE
COAT/CLEAR COAT
..................23-129
FINISH - INSPECTION, FIT
........30-10,30-12
FINISH - OPERATION, BASE COAT/CLEAR
COAT
.............................23-129FIRING ORDER, 3.9L V-6 ENGINE -
ENGINE..............................8I-2
FIRING ORDER, 5.2L/5.9L V-8 ENGINES -
ENGINE..............................8I-2
FIRING ORDER, DIESEL - FUEL
INJECTOR..........................14-58
FIT AND FINISH - INSPECTION.....30-10,30-12
FITTING - DESCRIPTION, QUICK
CONNECT...........................14-22
FITTING - STANDARD PROCEDURE,
CONNECTING ROD BEARING . . 9-144,9-202,9-88
FITTING - STANDARD PROCEDURE,
CRANKSHAFT MAIN BEARING......9-146,9-90
FITTING - STANDARD PROCEDURE,
MAIN BEARING..................9-203,9-33
FITTING - STANDARD PROCEDURE,
PISTON...............9-153,9-208,9-40,9-97
FITTING - STANDARD PROCEDURE,
PISTON RING...............9-154,9-41,9-98
FITTING, CONNECTING ROD BEARINGS -
STANDARD PROCEDURE-CONNECTING
ROD BEARING........................9-31
FITTING PISTON RINGS - STANDARD
PROCEDURE........................9-211
FITTING, PISTON RINGS - STANDARD
PROCEDURE-PISTON RING.............9-288
FITTINGS - STANDARD PROCEDURES,
QUICK-CONNECT.....................14-22
FIXED ORIFICE TUBE - DIAGNOSIS AND
TESTING...........................24-54
FLAG - INSTALLATION, SIDE VIEW
MIRROR...........................23-74
FLAG - REMOVAL, SIDE VIEW MIRROR . . . 23-74
FLARING - STANDARD PROCEDURE,
DOUBLE INVERTED.....................5-8
FLARING - STANDARD PROCEDURE, ISO....5-8
FLASHER - DESCRIPTION, COMBINATION . . 8L-7
FLASHER - INSTALLATION,
COMBINATION........................8L-8
FLASHER - OPERATION, COMBINATION....8L-7
FLASHER - REMOVAL, COMBINATION.....8L-8
FLOOR MATS - INSTALLATION, CARPETS . 23-123
FLOOR MATS - REMOVAL, CARPETS....23-123
FLOOR SHIFT BOOT - INSTALLATION,
4WD .............................23-122
FLOOR SHIFT BOOT - REMOVAL, 4WD . . . 23-122
FLOOR STOWAGE TRAY -
INSTALLATION, REAR................23-121
FLOOR STOWAGE TRAY - REMOVAL,
REAR.............................23-121
FLOW - 3.9L/5.2L/5.9L ENGINE -
DESCRIPTION, COOLING SYSTEM.........7-1
FLOW - 5.9L DIESEL - DESCRIPTION,
COOLING SYSTEM.....................7-1
FLOW - DIAGNOSIS AND TESTING,
RADIATOR COOLANT..........7-59,7-61,7-63
FLOW AND PRESSURE - DIAGNOSIS
AND TESTING, POWER STEERING........19-4
FLUID - DESCRIPTION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID - DESCRIPTION, TRANSFER CASE....0-5
FLUID - DIAGNOSIS AND TESTING,
CAUSES OF BURNT.....21-199,21-370,21-545,
21-715
FLUID - OPERATION, AUTOMATIC
TRANSMISSION.......................0-5
FLUID AND FILTER REPLACEMENT -
STANDARD PROCEDURE . 21-201,21-372,21-547,
21-717
FLUID CAPACITIES, SPECIFICATIONS.......0-6
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING....21-199,21-370,21-545,21-715
FLUID CONTAMINATION - DIAGNOSIS
AND TESTING, BRAKE..................5-14
FLUID DRAIN AND REFILL - STANDARD
PROCEDURE...........21-851,21-885,21-922
FLUID INDICATOR - DESCRIPTION,
WASHER
...........................8J-35
FLUID INDICATOR - DIAGNOSIS AND
TESTING, WASHER
...................8J-36
FLUID INDICATOR - OPERATION,
WASHER
...........................8J-35
FLUID LEAK - DIAGNOSIS AND TESTING,
CONVERTER HOUSING
. . . 21-148,21-319,21-491,
21-662
FLUID LEVEL - DIAGNOSIS AND
TESTING, EFFECTS OF INCORRECT
.....21-199,
21-370,21-545,21-715FLUID LEVEL - STANDARD PROCEDURE,
BRAKE..............................5-14
FLUID LEVEL CHECK - STANDARD
PROCEDURE.....21-199,21-370,21-545,21-715
FLUID LEVEL SWITCH - DESCRIPTION,
WASHER............................8R-7
FLUID LEVEL SWITCH - INSTALLATION,
WASHER............................8R-8
FLUID LEVEL SWITCH - OPERATION,
WASHER............................8R-7
FLUID LEVEL SWITCH - REMOVAL,
WASHER............................8R-8
FLUID LEVELS - INSPECTION............30-4
FLUID RESERVOIR - INSTALLATION.......5-15
FLUID RESERVOIR - REMOVAL..........5-15
FLUID, SPECIFICATIONS - BRAKE.........5-15
FLUID TYPES - DESCRIPTION.............0-5
FLUSH MEASUREMENTS,
SPECIFICATIONS - BODY GAP..........23-56
FLUSHING - STANDARD PROCEDURE,
COOLING SYSTEM CLEANING/
REVERSE............................7-16
FLUSHING COOLER AND TUBES -
WITHOUT RADIATOR IN-TANK
TRANSMISSION OIL COOLER -
STANDARD PROCEDURE.......7-80,7-83,7-86
FLUSHING COOLERS AND TUBES - WITH
RADIATOR IN-TANK TRANSMISSION
OIL COOLER - STANDARD
PROCEDURE.................7-79,7-83,7-85
FLUSHING POWER STEERING SYSTEM -
STANDARD PROCEDURE...............19-32
FLYWHEEL - ASSEMBLY................6-17
FLYWHEEL - DESCRIPTION..............6-16
FLYWHEEL - DIAGNOSIS AND TESTING....6-17
FLYWHEEL - DISASSEMBLY.............6-17
FLYWHEEL - OPERATION...............6-16
FOG LAMP - DIAGNOSIS AND TESTING....8L-9
FOG LAMP - INSTALLATION............8L-11
FOG LAMP - REMOVAL................8L-11
FOG LAMP UNIT - ADJUSTMENTS.......8L-12
FOG LAMP UNIT - INSTALLATION........8L-12
FOG LAMP UNIT - REMOVAL...........8L-11
FORE/AFT - ADJUSTMENT, FRONT DOOR . . 23-68
FORM, FINAL STEPS - NEW VEHICLE
PREPARATION.......................30-22
FORM-IN-PLACE GASKETS & SEALERS -
STANDARD PROCEDURE.....9-11,9-125,9-180,
9-237,9-68
FOUR-WHEEL DRIVE INDICATOR -
DIAGNOSIS AND TESTING..............8J-29
FRAME - DESCRIPTION.................13-6
FRAME - FRAME SERVICE..............13-6
FRAME - INSTALLATION, GRILLE........23-92
FRAME - REMOVAL, GRILLE............23-91
FRAME DIMENSION, SPECIFICATIONS.....13-7
FRAME SERVICE, FRAME...............13-6
FRONT - 2WD - DESCRIPTION.........2-7,2-8
FRONT - 4WD - DESCRIPTION...........2-14
FRONT - DESCRIPTION, CRANKSHAFT
OIL SEAL...................9-147,9-34,9-91
FRONT - INSTALLATION............5-14,5-27
FRONT - INSTALLATION...............22-12
FRONT - INSTALLATION, 1500/2500.......5-22
FRONT - INSTALLATION, 3500...........5-22
FRONT - INSTALLATION, CRANKSHAFT
OIL SEAL..............9-148,9-277,9-34,9-91
FRONT - INSTALLATION, PROPELLER
SHAFT...............................3-8
FRONT - OPERATION, CRANKSHAFT OIL
SEAL......................9-147,9-34,9-91
FRONT - REMOVAL................5-10,5-24
FRONT - REMOVAL, 1500/2500..........5-21
FRONT - REMOVAL, 3500...............5-22
FRONT - REMOVAL, CRANKSHAFT OIL
SEAL.................9-147,9-276,9-34,9-91
FRONT - REMOVAL, PROPELLER SHAFT....3-8
FRONT AIR DAM - INSTALLATION........13-2
FRONT AIR DAM - REMOVAL............13-1
FRONT AXLE - 216FBI - ADJUSTMENTS....3-17
FRONT AXLE - 216FBI - DESCRIPTION.....3-12
FRONT AXLE - 216FBI - INSTALLATION....3-17
FRONT AXLE - 216FBI - OPERATION......3-12
FRONT AXLE - 216FBI - REMOVAL
........3-16
FRONT AXLE - 248FBI - ADJUSTMENTS
....3-50
FRONT AXLE - 248FBI - DESCRIPTION
.....3-45
FRONT AXLE - 248FBI - INSTALLATION
....3-50
FRONT AXLE - 248FBI - OPERATION
......3-45
14 INDEXBR/BE
Description Group-Page Description Group-Page Description Group-Page