brake rotor DODGE RAM 2001 Service Service Manual

(3) Separate lens from lamp.
(4) Grasp bulb, push in slightly and rotate 1/2 turn
counter-clockwise.
PICKUP
(1) Disconnect and isolate the battery negative
cable.
(2) Remove screws from tail lamp.
(3) Grasp lamp, firmly pull lamp rearward to dis-
engage retaining studs.
(4) Remove socket from tail lamp.
(5) Separate tail lamp from cargo box.
(6) Pull bulb from socket.
INSTALLATION
CHASSIS CAB
(1) Install bulb in socket.
(2) Install lamp lens.
(3) Connect the battery negative cable.
PICKUP
(1) Install bulb in socket.
(2) Install socket in tail lamp.
(3) Position tail lamp in cargo box, engage retain-
ing studs and install screws.
(4) Connect the battery negative cable.
TAIL LAMP UNIT
REMOVAL
CAB CHASSIS
(1) Disconnect and isolate the battery negative
cable.
(2) Remove nuts attaching tail lamp to mounting
bracket (Fig. 29).
(3) Disengage tail lamp wire connector from body
wire harness.
(4) Separate tail lamp from vehicle.
PICKUP
(1) Disconnect and isolate the battery negative
cable.
(2) Remove screws from tail lamp (Fig. 30).
(3) Grasp lamp, firmly pull lamp rearward to dis-
engage retaining studs.
(4) Remove socket from tail lamp.
(5) Separate tail lamp from cargo box.
(6) Pull bulb from socket.
INSTALLATION
CAB CHASSIS
(1) Position tail lamp on vehicle.(2) Engage tail lamp wire connector to body wire
harness.
(3) Install nuts attaching tail lamp to mounting
bracket.
(4) Connect the battery negative cable.
PICKUP
(1) Install bulb in socket.
(2) Install socket in tail lamp.
(3) Position tail lamp in cargo box, engage retain-
ing studs and install screws.
(4) Connect the battery negative cable.
TURN SIGNAL CANCEL CAM
DESCRIPTION
The turn signal cancel cam is concealed within the
steering column below the steering wheel. The turn
signal cancel cam consists of two lobes that are inte-
gral to the lower surface of the clockspring rotor. The
clockspring mechanism provides turn signal cancella-
tion as well as a constant electrical connection
between the horn switch, driver airbag, speed control
switches, and remote radio switches on the steering
wheel and the instrument panel wire harness on the
steering column. The housing of the clockspring is
secured to the steering column and remains station-
Fig. 29 Tail, Brake, Turn Signal and Back-up
LampsÐCab Chassis
1 - LICENCE PLATE BRACKET
2 - FRAME
3 - TAILLAMP MOUNTING BRACKET
4 - TAILLAMP-BRAKE LAMP-BACKUP LAMP HOUSING
8L - 30 LAMPS/LIGHTING - EXTERIORBR/BE
TAIL LAMP (Continued)

ary. The rotor of the clockspring, including the turn
signal cancel cam lobes rotate with the steering
wheel.
The turn signal cancel cam is serviced as a unit
with the clockspring and cannot be repaired. If faulty
or damaged, the entire clockspring unit must be
replaced. (Refer to 8 - ELECTRICAL/RESTRAINTS/
CLOCKSPRING - REMOVAL).
OPERATION
The turn signal cancel cam has two lobes molded
into the lower surface of the clockspring rotor. When
the turn signals are activated by moving the multi-
function switch control stalk to a detent position, a
turn signal cancel actuator is extended from the
inside surface of the multi-function switch housing
toward the center of the steering column and theturn signal cancel cam. When the steering wheel is
rotated during a turning maneuver, one of the two
turn signal cancel cam lobes will contact the turn sig-
nal cancel actuator. The cancel actuator latches
against the cancel cam rotation in the direction oppo-
site that which is signaled. In other words, if the left
turn signal detent is selected, the lobes of the cancel
cam will ratchet past the cancel actuator when the
steering wheel is rotated to the left, but will unlatch
the cancel actuator as the steering wheel rotates to
the right and returns to center, which will cancel the
turn signal event and release the control stalk from
the detent so it returns to the neutral Off position.
UNDERHOOD LAMP
REMOVAL
(1) Disconnect and isolate the battery negative
cable.
(2) Insert a small flat blade in the access slot
between the lamp base and lamp lens.
(3) Pry the lamp lens upward and remove the
lamp lens (Fig. 31).
(4) Depress the bulb terminal inward (Fig. 32) to
release the bulb.
Fig. 30 Tail, Brake, Turn Signal and Back-up Lamp
Bulb
1 - TAIL LAMP
2 - SCREW
3 - LIGHTING HARNESS
4 - BULB
5 - RETAINING CLIP
6 - RETAINING STUDS
Fig. 31 Underhood Lamp Lens
1 - LAMP
2 - LAMP LENS
BR/BELAMPS/LIGHTING - EXTERIOR 8L - 31
TURN SIGNAL CANCEL CAM (Continued)

STUDS
REMOVAL
(1) Raise and support the vehicle.
(2) Remove the wheel and tire assembly.
(3) Remove the brake caliper, caliper adapter and
rotor, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - REMOVAL).
(4) Remove the stud from the hub with Remover
C-4150A (Fig. 21).
INSTALLATION
(1) Install the new stud into the hub flange.
(2) Install the three washers onto the stud, then
install the lug nut with the flat side of the nut
against the washers.
(3) Tighten the lug nut until the stud is pulled
into the hub flange. Verify that the stud is properly
seated into the flange.
(4) Remove the lug nut and washers.
(5) Install the brake rotor, caliper adapter, and cal-
iper, (Refer to 5 - BRAKES/HYDRAULIC/MECHAN-
ICAL/ROTORS - INSTALLATION).
(6) Install the wheel and tire assembly, (Refer to
22 - TIRES/WHEELS/WHEELS - STANDARD PRO-
CEDURE), use new the lug nut on stud or studs that
were replaced.
(7) Remove the support and lower vehicle.
WHEEL COVER
REMOVAL
(1) Insert a hub/cap remover/installer combination
tool around the circumference of the wheel between
the wheel and wheel trim cover.
(2) Twist the tool to remove wheel trim cover.
INSTALLATION - REAR
(1) Install one 1 1/2 in. valve stem extension on
each rear inner wheel.
NOTE: A 3/8 in. drive 10mm deep wheel socket with
a 10 in. or greater extension can be used to remove
the existing valve stem cap and install the exten-
sion.
(2) Install one 1 in. valve stem extension on each
outer wheel.
(3) Align the cooling windows of the wheel skin
with the cooling windows of the wheel. Seat one side
of the wheel skin's retainer onto the wheel. Using a
rubber mallet, strike thew wheel skin on the outer
circumference. Strike at several locations around the
circumference until the skin is fully seated.
NOTE: The wheel skin and the hub cap are fully
seated when there is a consistent gap between the
skin/cap and the wheel.
(4) Tug on the hub/cap wheel skin to ensure that
they are properly installed.
INSTALLATION - FRONT
(1) Align the valve stem with the notch in the
wheel skin.
(2) Seat on side of the wheel skin's wire retainer
on to the wheel.
(3) Using a rubber mallet, strike the opposite side
of the wheel skin until the skin is properly seated.
NOTE: The wheel skin and the hub cap are fully
seated when there is a consistant gap between the
skin/ cap and the wheel.
(4) Tug on the hub cap/wheel skin to ensure that
they are properly installed.
Fig. 21 Wheel Stud Removal
1 - REMOVER
2 - WHEEL STUD
22 - 12 TIRES/WHEELSBR/BE

BODY CONTROL/CENTRAL TIMER
MODULE - INSTALLATION...............8E-6
BODY CONTROL/CENTRAL TIMER
MODULE - OPERATION.................8E-3
BODY CONTROL/CENTRAL TIMER
MODULE - REMOVAL..................8E-5
BODY GAP AND FLUSH
MEASUREMENTS, SPECIFICATIONS......23-56
BODY OPENING DIMENSIONS,
SPECIFICATIONS.....................23-60
BODY SEALER LOCATIONS,
SPECIFICATIONS.....................23-47
BODY SEALING - INSPECTION..........30-10
BODY SIDE MOLDINGS - INSTALLATION . . 23-87
BODY SIDE MOLDINGS - REMOVAL......23-87
BODY STRIPES AND DECALS -
INSTALLATION.......................23-87
BODY STRIPES AND DECALS -
REMOVAL..........................23-87
BODY VENT - INSTALLATION..........23-126
BODY VENT - REMOVAL..............23-126
BOOST PRESSURE - DIAGNOSIS AND
TESTING...........................14-89
BOOSTER - DIAGNOSIS AND TESTING,
HYDRAULIC..........................5-17
BOOSTER - DIAGNOSIS AND TESTING,
MASTER CYLINDER/POWER.............5-29
BOOSTER - INSTALLATION, POWER
BRAKE..............................5-20
BOOSTER - REMOVAL, POWER BRAKE....5-19
BOOT - INSTALLATION, 4WD FLOOR
SHIFT..............................23-122
BOOT - MANUAL TRANSMISSION -
INSTALLATION, SHIFT................23-122
BOOT - MANUAL TRANSMISSION -
REMOVAL, SHIFT....................23-122
BOOT - REMOVAL, 4WD FLOOR SHIFT . . . 23-122
BORE, DE-GLAZE - STANDARD
PROCEDURE-CYLINDER...............9-264
BORE HONING - STANDARD
PROCEDURE, CYLINDER . . 9-10,9-126,9-180,9-69
BORE REPAIR - STANDARD
PROCEDURE, CAM...................9-267
BORE REPAIR - STANDARD
PROCEDURE, CYLINDER...............9-265
BOX - ASSEMBLY, GLOVE.............23-112
BOX - DISASSEMBLY, GLOVE..........23-112
BOX - INSTALLATION, CARGO..........23-97
BOX - INSTALLATION, GLOVE..........23-113
BOX - REMOVAL, CARGO..............23-96
BOX - REMOVAL, GLOVE.............23-112
BOX LAMP AND SWITCH -
INSTALLATION, GLOVE................8L-35
BOX LAMP AND SWITCH - REMOVAL,
GLOVE.............................8L-35
BOX LATCH STRIKER - INSTALLATION,
GLOVE............................23-113
BOX LATCH STRIKER - REMOVAL,
GLOVE............................23-113
BOX OPENING UPPER TRIM -
INSTALLATION, GLOVE...............23-114
BOX OPENING UPPER TRIM - REMOVAL,
GLOVE............................23-114
B-PILLAR DOOR SEAL - INSTALLATION . . 23-152
B-PILLAR DOOR SEAL - REMOVAL......23-152
B-PILLAR TRIM - INSTALLATION
.......23-120
B-PILLAR TRIM - REMOVAL
...........23-120
BR PAINT COLOR CODES,
SPECIFICATIONS - 2001
..............23-129
BRACKET - INSTALLATION, CAB
CHASSIS ADAPTER
....................13-9
BRACKET - INSTALLATION, REARVIEW
MIRROR SUPPORT
..................23-126
BRACKET - REMOVAL, CAB CHASSIS
ADAPTER
............................13-9
BRAKE - DESCRIPTION, CONTROLLER
ANTILOCK
..........................8E-11
BRAKE - INSPECTION, PARKING
.........30-17
BRAKE - INSTALLATION, CONTROLLER
ANTILOCK
..........................8E-12
BRAKE - OPERATION, CONTROLLER
ANTILOCK
..........................8E-11
BRAKE - REMOVAL, CONTROLLER
ANTILOCK
..........................8E-12
BRAKE BOOSTER - INSTALLATION,
POWER
.............................5-20
BRAKE BOOSTER - REMOVAL, POWER
....5-19BRAKE CABLE - 2500/3500 WITH REAR
DISC BRAKES - INSTALLATION, REAR
PARK...............................5-38
BRAKE CABLE - 2500/3500 WITH REAR
DISC BRAKES - REMOVAL, REAR
PARK...............................5-37
BRAKE CABLE - INSTALLATION, FRONT
PARKING............................5-39
BRAKE CABLE - REMOVAL, FRONT
PARKING............................5-37
BRAKE CABLE 2500/3500 SERIES WITH
DRUM BRAKES - INSTALLATION, REAR
PARK...............................5-39
BRAKE CABLES - 1500 SERIES -
INSTALLATION, REAR PARK.............5-39
BRAKE CABLES - 1500 SERIES -
REMOVAL, REAR PARK.................5-37
BRAKE CABLES 2500/3500 SERIES WITH
DRUM BRAKES - REMOVAL, REAR
PARK...............................5-38
BRAKE CALIPERS - ASSEMBLY, DISC......5-12
BRAKE CALIPERS - CLEANING, DISC......5-12
BRAKE CALIPERS - DISASSEMBLY, DISC . . . 5-11
BRAKE CALIPERS - INSPECTION, DISC....5-12
BRAKE DRUM - ADJUSTMENT, REAR......5-34
BRAKE DRUM - DIAGNOSIS AND
TESTING............................5-33
BRAKE DRUM MACHINING - STANDARD
PROCEDURE.........................5-33
BRAKE FLUID CONTAMINATION -
DIAGNOSIS AND TESTING..............5-14
BRAKE FLUID LEVEL - STANDARD
PROCEDURE.........................5-14
BRAKE FLUID, SPECIFICATIONS..........5-15
BRAKE INDICATOR - DESCRIPTION,
BRAKE/PARK........................8J-16
BRAKE INDICATOR - DIAGNOSIS AND
TESTING...........................8J-16
BRAKE INDICATOR - OPERATION,
BRAKE/PARK........................8J-16
BRAKE LAMP SWITCH - DESCRIPTION....8L-4
BRAKE LAMP SWITCH - DIAGNOSIS
AND TESTING........................8L-5
BRAKE LAMP SWITCH - INSTALLATION....8L-5
BRAKE LAMP SWITCH - OPERATION......8L-4
BRAKE LAMP SWITCH - REMOVAL.......8L-5
BRAKE ROTOR - DIAGNOSIS AND
TESTING, DISC.......................5-20
BRAKE SHOES - 2500/3500 -
INSTALLATION, REAR DRUM IN HAT
PARK...............................5-42
BRAKE SHOES - 2500/3500 - REMOVAL,
REAR DRUM IN HAT PARK..............5-41
BRAKE SHOES-11 INCH - INSTALLATION,
REAR...............................5-27
BRAKE SHOES-11 INCH - REMOVAL,
REAR...............................5-25
BRAKE, SPECIFICATIONS - BASE..........5-2
BRAKE SYSTEM - DIAGNOSIS AND
TESTING, BASE........................5-5
BRAKE/PARK BRAKE INDICATOR -
DESCRIPTION
.......................8J-16
BRAKE/PARK BRAKE INDICATOR -
OPERATION
.........................8J-16
BRAKES - DESCRIPTION, 2500/3500
WITH REAR DISC
.....................5-35
BRAKES - INSPECTION, SERVICE
........30-17
BRAKES - INSTALLATION, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR DISC
..........................5-38
BRAKES - INSTALLATION, REAR PARK
BRAKE CABLE 2500/3500 SERIES
WITH DRUM
.........................5-39
BRAKES - OPERATION, 2500/3500 WITH
REAR DISC
..........................5-36
BRAKES - REMOVAL, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR DISC
..........................5-37
BRAKES - REMOVAL, REAR PARK
BRAKE CABLES 2500/3500 SERIES
WITH DRUM
.........................5-38
BRAKES, SPECIAL TOOLS - BASE
.........5-4
BREAKER - DESCRIPTION, CIRCUIT
....8W-97-4
BREAKER - DIAGNOSIS & TESTING,
CIRCUIT
.........................8W-97-4
BREAK-IN - STANDARD PROCEDURE,
A/C COMPRESSOR CLUTCH
............24-13BREATHER VAPOR CANISTER -
INSTALLATION, CRANKCASE............9-242
BREATHER VAPOR CANISTER -
REMOVAL, CRANKCASE...............9-241
BUCKLE - INSTALLATION, FRONT SEAT
BELT ..............................8O-20
BUCKLE - INSTALLATION, REAR SEAT
BELT ..............................8O-27
BUCKLE - REMOVAL, FRONT SEAT BELT . . 8O-20
BUCKLE - REMOVAL, REAR SEAT BELT . . . 8O-27
BUILT-IN INDICATOR TEST - STANDARD
PROCEDURE........................8F-11
BUMPER - DESCRIPTION, JOUNCE....2-28,2-9
BUMPER - INSTALLATION, FRONT........13-4
BUMPER - INSTALLATION, REAR.........13-5
BUMPER - INSTALLATION, SLAM........23-66
BUMPER - OPERATION, JOUNCE......2-28,2-9
BUMPER - REMOVAL, FRONT............13-3
BUMPER - REMOVAL, REAR.............13-5
BUMPER - REMOVAL, SLAM...........23-66
BUMPERS - DESCRIPTION..............13-1
BUMPER-SPORT - INSTALLATION,
FRONT..............................13-4
BUMPER-SPORT - REMOVAL, FRONT......13-4
BURNT FLUID - DIAGNOSIS AND
TESTING, CAUSES OF . . . 21-199,21-370,21-545,
21-715
BUS - DESCRIPTION, CCD DATA..........8E-6
BUS - DIAGNOSIS AND TESTING, CCD
D ATA................................8E-11
BUS - OPERATION, CCD DATA...........8E-7
BUSHING - INSTALLATION,
DISTRIBUTOR...............9-150,9-37,9-94
BUSHING - INSTALLATION, EXTENSION
HOUSING........21-198,21-369,21-544,21-714
BUSHING - REMOVAL, DISTRIBUTOR....9-150,
9-37,9-94
BUSHING - REMOVAL, EXTENSION
HOUSING........21-198,21-369,21-544,21-714
BUSHING AND SEAL - INSTALLATION,
EXTENSION HOUSING....21-850,21-885,21-921
BUSHING AND SEAL - REMOVAL,
EXTENSION HOUSING....21-850,21-885,21-921
BUSHINGS - INSTALLATION.............2-28
BUSHINGS - REMOVAL.................2-28
BYPASS HOSE WITH AIR CONDITIONING
- INSTALLATION, WATER PUMP..........7-77
BYPASS HOSE WITH AIR CONDITIONING
- REMOVAL, WATER PUMP..............7-74
BYPASS HOSE WITHOUT AIR
CONDITIONING - INSTALLATION,
WATER PUMP........................7-78
BYPASS HOSE WITHOUT AIR
CONDITIONING - REMOVAL, WATER
PUMP..............................7-77
CAB - INSTALLATION, CLUB/QUAD.......8O-20
CAB - INSTALLATION, STANDARD.......8O-19
CAB - REMOVAL, CLUB/QUAD..........8O-19
CAB - REMOVAL, STANDARD...........8O-18
CAB CHASSIS ADAPTER BRACKET -
INSTALLATION........................13-9
CAB CHASSIS ADAPTER BRACKET -
REMOVAL...........................13-9
CAB SIDE PANEL SPEAKER -
INSTALLATION, REAR.................8A-21
CAB SIDE PANEL SPEAKER - REMOVAL,
REAR..............................8A-20
CABLE - 2500/3500 WITH REAR DISC
BRAKES - INSTALLATION, REAR PARK
BRAKE..............................5-38
CABLE - 2500/3500 WITH REAR DISC
BRAKES - REMOVAL, REAR PARK
BRAKE..............................5-37
CABLE - ADJUSTMENTS,
TRANSMISSION THROTTLE VALVE.....21-254,
21-425,21-598,21-771
CABLE - DESCRIPTION.................8P-4
CABLE - DESCRIPTION, ANTENNA BODY . . . 8A-4
CABLE - DESCRIPTION, BATTERY........8F-19
CABLE - DESCRIPTION, SPARK PLUG.....8I-19
CABLE - DESCRIPTION, THROTTLE
VALVE
..........21-253,21-424,21-597,21-770
CABLE - INSTALLATION, CHECK
.........23-63
CABLE - INSTALLATION, FRONT
PARKING BRAKE
......................5-39
CABLE - INSTALLATION, INSTRUMENT
PANEL ANTENNA
.....................8A-10
CABLE - INSTALLATION, LATCH RELEASE
. 23-101
BR/BEINDEX 5
Description Group-Page Description Group-Page Description Group-Page

DIESEL - DESCRIPTION................25-1
DIESEL - DESCRIPTION........14-102,14-103
DIESEL - DESCRIPTION.................8I-5
DIESEL - DESCRIPTION, 5.9L............11-3
DIESEL - DESCRIPTION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - DESCRIPTION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - DESCRIPTION, COOLING
SYSTEM FLOW - 5.9L...................7-1
DIESEL - DESCRIPTION, ENGINE 5.9L....9-231
DIESEL - DESCRIPTION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - DESCRIPTION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-54
DIESEL - DESCRIPTION, FAN DRIVE
VISCOUS CLUTCH - 5.9L...............7-57
DIESEL - DESCRIPTION, MAINTENANCE
SCHEDULES - 24-VALVE CUMMINS
TURBO..............................0-22
DIESEL - DESCRIPTION, RADIATOR -
5.9L................................7-63
DIESEL - DESCRIPTION, TRANS COOLER
- 5.9L..............................7-85
DIESEL - DESCRIPTION, VACUUM PUMP
- 5.9L..............................7-34
DIESEL - DESCRIPTION, WATER PUMP -
5.9L................................7-73
DIESEL - FUEL INJECTOR FIRING ORDER . 14-58
DIESEL - INSPECTION, EXHAUST PIPE -
5.9L................................11-9
DIESEL - INSPECTION, RADIATOR - 5.9L . . . 7-65
DIESEL - INSPECTION, RADIATOR FAN -
5.9L................................7-44
DIESEL - INSPECTION, TAILPIPE - 5.9L . . . 11-12
DIESEL - INSPECTION, WATER PUMP -
5.9L................................7-73
DIESEL - INSTALLATION..............14-103
DIESEL - INSTALLATION................8I-8
DIESEL - INSTALLATION, BELT
TENSIONERS - 5.9L...................7-23
DIESEL - INSTALLATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - INSTALLATION, DRIVE BELTS -
5.9L................................7-34
DIESEL - INSTALLATION, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - INSTALLATION, ENGINE
COOLANT THERMOSTAT - 5.9L...........7-55
DIESEL - INSTALLATION, EXHAUST PIPE
- 5.9L..............................11-10
DIESEL - INSTALLATION, MUFFLER -
5.9L...............................11-11
DIESEL - INSTALLATION, RADIATOR -
5.9L................................7-65
DIESEL - INSTALLATION, RADIATOR FAN
- 5.9L..............................7-45
DIESEL - INSTALLATION, TAILPIPE - 5.9L . 11-12
DIESEL - INSTALLATION, TRANS
COOLER - 5.9L.......................7-88
DIESEL - INSTALLATION, VACUUM
PUMP - 5.9L.........................7-37
DIESEL - INSTALLATION, WATER PUMP -
5.9L................................7-74
DIESEL - OPERATION
.................8E-18
DIESEL - OPERATION
.................25-19
DIESEL - OPERATION
..........14-102,14-103
DIESEL - OPERATION
...................8I-5
DIESEL - OPERATION, BELT
TENSIONERS - 5.9L
...................7-23
DIESEL - OPERATION, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L
............................7-41
DIESEL - OPERATION, ENGINE BLOCK
HEATER - 5.9L
........................7-47
DIESEL - OPERATION, ENGINE COOLANT
THERMOSTAT - 5.9L
...................7-54
DIESEL - OPERATION, FAN DRIVE
VISCOUS CLUTCH - 5.9L
...............7-57
DIESEL - OPERATION, FUEL DELIVERY
. . . 14-56
DIESEL - OPERATION, NON-MONITORED
CIRCUITS
...........................25-23
DIESEL - OPERATION, RADIATOR - 5.9L
. . . 7-63
DIESEL - OPERATION, TRANS COOLER -
5.9L
................................7-85DIESEL - OPERATION, VACUUM PUMP -
5.9L................................7-35
DIESEL - OPERATION, WATER PUMP -
5.9L................................7-73
DIESEL - REMOVAL............14-103,14-104
DIESEL - REMOVAL....................8I-7
DIESEL - REMOVAL, BELT TENSIONERS -
5.9L................................7-23
DIESEL - REMOVAL, COOLANT
RECOVERY CONTAINER - 3.9L/5.2L/
5.9L/5.9L............................7-41
DIESEL - REMOVAL, DRIVE BELTS - 5.9L . . 7-33
DIESEL - REMOVAL, ENGINE BLOCK
HEATER - 5.9L........................7-47
DIESEL - REMOVAL, ENGINE COOLANT
THERMOSTAT - 5.9L...................7-55
DIESEL - REMOVAL, EXHAUST PIPE -
5.9L................................11-9
DIESEL - REMOVAL, MUFFLER - 5.9L.....11-11
DIESEL - REMOVAL, RADIATOR - 5.9L.....7-63
DIESEL - REMOVAL, RADIATOR FAN -
5.9L................................7-44
DIESEL - REMOVAL, TAILPIPE - 5.9L.....11-12
DIESEL - REMOVAL, VACUUM PUMP -
5.9L................................7-35
DIESEL - REMOVAL, WATER PUMP -
5.9L................................7-73
DIESEL ENGINE - DESCRIPTION, FUEL
REQUIREMENTS.......................0-2
DIESEL ENGINE - DIAGNOSIS AND
TESTING............................11-4
DIESEL ENGINE - DIAGNOSIS AND
TESTING, COOLING SYSTEM............7-12
DIESEL ENGINE - INSTALLATION........19-35
DIESEL ENGINE - REMOVAL............19-33
DIESEL ENGINE - STANDARD
PROCEDURE, DRAINING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - STANDARD
PROCEDURE, REFILLING COOLING
SYSTEM 5.9L........................7-15
DIESEL ENGINE - TORQUE.............14-90
DIESEL ENGINE, SPECIAL TOOLS - 5.9L . . 9-244
DIESEL ENGINES - DESCRIPTION,
COMPONENT MONITORS..............25-18
DIESEL ENGINES - FUEL SYSTEM
PRESSURES........................14-58
DIESEL FUEL DELIVERY SYSTEM -
DESCRIPTION.......................14-54
DIESEL FUEL INJECTION SYSTEM -
DESCRIPTION.......................14-87
DIESEL FUEL SYSTEM, SPECIAL TOOLS . . 14-59
DIESEL FUEL TANK - DESCRIPTION......14-78
DIESEL, SPECIFICATIONS - 5.9L.........9-242
DIESEL WITH AUTO. TRANS. -
INSTALLATION..................8P-11,8P-4
DIESEL WITH AUTO. TRANS. - REMOVAL . . 8P-4,
8P-8
DIFFERENTIAL - ASSEMBLY . . 3-128,3-159,3-188,
3-37,3-69,3-98
DIFFERENTIAL - DISASSEMBLY....3-128,3-158,
3-188,3-36,3-68,3-97
DIFFERENTIAL - INSTALLATION....3-129,3-159,
3-188,3-37,3-69,3-98
DIFFERENTIAL - POWR-LOK - ASSEMBLY . 3-163
DIFFERENTIAL - POWR-LOK -
DISASSEMBLY.......................3-161
DIFFERENTIAL - REMOVAL . . 3-127,3-158,3-187,
3-36,3-68,3-96
DIFFERENTIAL - TRAC-LOK - ASSEMBLY . . 3-101,
3-132,3-190
DIFFERENTIAL - TRAC-LOK -
DISASSEMBLY..............3-130,3-190,3-99
DIFFERENTIAL CASE BEARINGS -
INSTALLATION . . . 3-103,3-134,3-164,3-192,3-39,
3-71
DIFFERENTIAL CASE BEARINGS -
REMOVAL . . . 3-103,3-134,3-164,3-192,3-39,3-71
DIMENSION, SPECIFICATIONS - FRAME....13-7
DIMENSIONS, SPECIFICATIONS - BODY
OPENING...........................23-60
DIODE - INSTALLATION............8W-01-10
DIODE - REMOVAL
................8W-01-10
DIODE REPLACEMENT - STANDARD
PROCEDURE
.........................24-7
DISC - DESCRIPTION, CLUTCH
............6-7
DISC - INSTALLATION, CLUTCH
...........6-9
DISC - OPERATION, CLUTCH
.............6-8DISC - REMOVAL, CLUTCH...............6-8
DISC BRAKE CALIPERS - ASSEMBLY......5-12
DISC BRAKE CALIPERS - CLEANING......5-12
DISC BRAKE CALIPERS - DISASSEMBLY . . . 5-11
DISC BRAKE CALIPERS - INSPECTION.....5-12
DISC BRAKE ROTOR - DIAGNOSIS AND
TESTING............................5-20
DISC BRAKES - DESCRIPTION,
2500/3500 WITH REAR.................5-35
DISC BRAKES - INSTALLATION, REAR
PARK BRAKE CABLE - 2500/3500
WITH REAR..........................5-38
DISC BRAKES - OPERATION, 2500/3500
WITH REAR..........................5-36
DISC BRAKES - REMOVAL, REAR PARK
BRAKE CABLE - 2500/3500 WITH
REAR...............................5-37
DISCHARGE LINE - INSTALLATION,
SUCTION...........................24-51
DISCHARGE LINE - REMOVAL, SUCTION . . 24-50
DISPLAY TEST MODE - DESCRIPTION,
STATE ..............................25-1
DISTRIBUTION - DESCRIPTION, POWER . 8W-97-1
DISTRIBUTION - OPERATION, POWER . . 8W-97-1
DISTRIBUTION CENTER - DESCRIPTION,
POWER..........................8W-97-7
DISTRIBUTION CENTER - INSTALLATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - OPERATION,
POWER..........................8W-97-8
DISTRIBUTION CENTER - REMOVAL,
POWER...........................8W-97-8
DISTRIBUTION SYSTEMS, SPECIAL
TOOLS - POWER...................8W-97-2
DISTRIBUTOR - DESCRIPTION..........8I-10
DISTRIBUTOR - INSTALLATION..........8I-11
DISTRIBUTOR - OPERATION............8I-11
DISTRIBUTOR - REMOVAL..............8I-11
DISTRIBUTOR BUSHING - INSTALLATION . 9-150,
9-37,9-94
DISTRIBUTOR BUSHING - REMOVAL.....9-150,
9-37,9-94
DISTRIBUTOR CAP - DIAGNOSIS AND
TESTING............................8I-12
DISTRIBUTOR ROTOR - DIAGNOSIS AND
TESTING............................8I-13
DOME LAMP - INSTALLATION..........8L-33
DOME LAMP - REMOVAL..............8L-33
DOOR - ADJUSTMENT, CARGO..........23-78
DOOR - INSTALLATION...........23-68,23-78
DOOR - INSTALLATION, BLEND.........24-38
DOOR - INSTALLATION, FUEL FILL.......23-95
DOOR - INSTALLATION, HEAT/DEFROST . . . 24-39
DOOR - INSTALLATION, PANEL/DEFROST . . 24-39
DOOR - INSTALLATION, RECIRCULATION . . 24-39
DOOR - REMOVAL...............23-68,23-78
DOOR - REMOVAL, BLEND.............24-38
DOOR - REMOVAL, FUEL FILL..........23-95
DOOR - REMOVAL, HEAT/DEFROST......24-38
DOOR - REMOVAL, PANEL/DEFROST.....24-38
DOOR - REMOVAL, RECIRCULATION.....24-39
DOOR ACTUATOR - INSTALLATION,
BLEND.............................24-26
DOOR ACTUATOR - INSTALLATION,
HEAT/DEFROST......................24-27
DOOR ACTUATOR - INSTALLATION,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - INSTALLATION,
RECIRCULATION
.....................24-28
DOOR ACTUATOR - REMOVAL, BLEND
....24-25
DOOR ACTUATOR - REMOVAL,
HEAT/DEFROST
......................24-26
DOOR ACTUATOR - REMOVAL,
PANEL/DEFROST
.....................24-27
DOOR ACTUATOR - REMOVAL,
RECIRCULATION
.....................24-27
DOOR AJAR SWITCH - DESCRIPTION
....8L-34
DOOR AJAR SWITCH - DIAGNOSIS AND
TESTING
...........................8L-34
DOOR AJAR SWITCH - INSTALLATION
....8L-35
DOOR AJAR SWITCH - REMOVAL
........8L-35
DOOR CYLINDER LOCK SWITCH -
DESCRIPTION
........................8N-5
DOOR CYLINDER LOCK SWITCH -
DIAGNOSIS & TESTING
................8N-5
DOOR CYLINDER LOCK SWITCH -
INSTALLATION
.......................8N-6
BR/BEINDEX 11
Description Group-Page Description Group-Page Description Group-Page

RELAY - OPERATION, A/C COMPRESSOR
CLUTCH............................24-17
RELAY - OPERATION, BLOWER MOTOR . . . 24-22
RELAY - OPERATION, ENGINE STARTER
MOTOR............................8F-42
RELAY - OPERATION, FUEL HEATER......14-63
RELAY - OPERATION, FUEL INJECTION
PUMP.............................14-99
RELAY - OPERATION, FUEL PUMP.......14-41
RELAY - OPERATION, HEADLAMP........8L-17
RELAY - OPERATION, HEATED SEAT.....8G-12
RELAY - OPERATION, HORN.............8H-3
RELAY - OPERATION, INTAKE AIR
HEATER ...........................14-102
RELAY - OPERATION, RADIO CHOKE......8A-8
RELAY - OPERATION, WIPER...........8R-15
RELAY - REMOVAL, A/C COMPRESSOR
CLUTCH............................24-18
RELAY - REMOVAL, AUTOMATIC SHUT
DOWN..............................8I-4
RELAY - REMOVAL, BLOWER MOTOR....24-23
RELAY - REMOVAL, ENGINE STARTER
MOTOR............................8F-43
RELAY - REMOVAL, FUEL HEATER.......14-65
RELAY - REMOVAL, FUEL PUMP........14-41
RELAY - REMOVAL, HEADLAMP.........8L-18
RELAY - REMOVAL, HEATED SEAT.......8G-13
RELAY - REMOVAL, INTAKE AIR HEATER . 14-102
RELAY - REMOVAL, RADIO CHOKE.........8A-9
RELAY - REMOVAL, WIPER............8R-17
RELAYS - DIAGNOSIS AND TESTING,
ASD AND FUEL PUMP..................8I-3
RELEASE - INSTALLATION..............5-41
RELEASE - REMOVAL..................5-40
RELEASE - STANDARD PROCEDURE,
FUEL SYSTEM PRESSURE..............14-3
RELEASE BEARING - DESCRIPTION,
CLUTCH.............................6-14
RELEASE BEARING - INSTALLATION,
CLUTCH.............................6-15
RELEASE BEARING - OPERATION,
CLUTCH.............................6-14
RELEASE BEARING - REMOVAL, CLUTCH . . . 6-15
RELEASE CABLE - INSTALLATION........23-83
RELEASE CABLE - INSTALLATION, LATCH . 23-101
RELEASE CABLE - REMOVAL...........23-82
RELEASE CABLE - REMOVAL, LATCH....23-101
RELIEF VALVE - CLEANING, OIL
PRESSURE.........................9-297
RELIEF VALVE - DESCRIPTION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - INSPECTION, OIL
PRESSURE.........................9-297
RELIEF VALVE - INSTALLATION, OIL
PRESSURE.........................9-298
RELIEF VALVE - OPERATION, HIGH
PRESSURE.........................24-46
RELIEF VALVE - REMOVAL, OIL
PRESSURE.........................9-297
REMINDER - INSPECTION, TRIP
COMPUTER/MAINTENANCE.............30-17
REMINDER INDICATOR - DESCRIPTION,
SERVICE...........................8J-28
REMINDER INDICATOR - OPERATION,
SERVICE...........................8J-28
REMOTE KEYLESS ENTRY SYSTEM -
DESCRIPTION........................8N-2
REMOTE KEYLESS ENTRY SYSTEM -
DIAGNOSIS AND TESTING, POWER
LOCK...............................8N-4
REMOTE KEYLESS ENTRY SYSTEM -
OPERATION..........................8N-3
REMOTE KEYLESS ENTRY
TRANSMITTER - DESCRIPTION..........8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - DIAGNOSIS AND
TESTING............................8N-7
REMOTE KEYLESS ENTRY
TRANSMITTER - OPERATION............8N-7
REMOTE SWITCHES - DESCRIPTION.....8A-15
REMOTE SWITCHES - DIAGNOSIS AND
TESTING
...........................8A-16
REMOTE SWITCHES - OPERATION
.......8A-15
REMOVAL/INSTALLATION, FUEL FILLER
CAP
...............................25-33
REMOVAL/INSTALLATION, FUEL HEATER
. . 14-63
REPAIR - DESCRIPTION, THREADED
HOLE
.............................Intro.-6REPAIR - STANDARD PROCEDURE,
ALUMINUM THREAD....21-159,21-330,21-502,
21-673
REPAIR - STANDARD PROCEDURE, CAM
BORE..............................9-267
REPAIR - STANDARD PROCEDURE,
CYLINDER BORE.....................9-265
REPAIR DAMAGED OR WORN THREADS
- STANDARD PROCEDURE....9-11,9-125,9-181,
9-238,9-68
REPAIRING LEAKS - STANDARD
PROCEDURES........................22-8
REQUIREMENTS - DESCRIPTION,
COOLING SYSTEM....................24-1
REQUIREMENTS - DIESEL ENGINE -
DESCRIPTION, FUEL....................0-2
REQUIREMENTS - GAS ENGINES -
DESCRIPTION, FUEL....................0-1
RESERVOIR - DESCRIPTION, VACUUM....24-29
RESERVOIR - DESCRIPTION, VACUUM . . . 8P-13
RESERVOIR - DESCRIPTION, WASHER . . . 8R-10
RESERVOIR - INSTALLATION, FLUID......5-15
RESERVOIR - INSTALLATION, VACUUM . . . 24-30
RESERVOIR - INSTALLATION, VACUUM . . . 8P-14
RESERVOIR - INSTALLATION, WASHER . . . 8R-11
RESERVOIR - OPERATION, VACUUM.....24-29
RESERVOIR - OPERATION, WASHER.....8R-10
RESERVOIR - REMOVAL, FLUID..........5-15
RESERVOIR - REMOVAL, VACUUM.......24-30
RESERVOIR - REMOVAL, VACUUM.......8P-13
RESERVOIR - REMOVAL, WASHER......8R-10
RESISTANCE, 3.9L/5.2L/5.9L ENGINES -
IGNITION COIL........................8I-3
RESISTANCE, 8.0L V-10 ENGINE -
IGNITION COIL........................8I-3
RESISTANCE, SPECIFICATIONS - SPARK
PLUG CABLE.........................8I-3
RESISTOR BLOCK - DESCRIPTION,
BLOWER MOTOR....................24-23
RESISTOR BLOCK - DIAGNOSIS AND
TESTING, BLOWER MOTOR
............24-24
RESISTOR BLOCK - INSTALLATION,
BLOWER MOTOR
....................24-24
RESISTOR BLOCK - OPERATION,
BLOWER MOTOR
....................24-23
RESISTOR BLOCK - REMOVAL, BLOWER
MOTOR
............................24-24
RESONATOR - INSTALLATION
...........11-13
RESONATOR - REMOVAL
..............11-13
RESTRAINTS - DESCRIPTION
............8O-1
RESTRAINTS - INSPECTION, SEAT
BELTS, SHOULDER BELTS,
RETRACTORS AND HEAD
..............30-12
RESTRAINTS - OPERATION
.............8O-2
RESTRAINTS - WARNING
...............8O-3
RESTRICTIONS - DIAGNOSIS AND
TESTING, FUEL SUPPLY
...............14-56
RETAINER - ASSEMBLY, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-581,21-752
RETAINER - CLEANING, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-236,
21-406,21-580,21-752
RETAINER - DESCRIPTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - DISASSEMBLY,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-235,21-405,21-580,
21-751
RETAINER - INSPECTION,
OVERRUNNING CLUTCH CAM/
OVERDRIVE PISTON
.....21-236,21-406,21-580,
21-752
RETAINER - INSTALLATION,
CRANKSHAFT REAR OIL SEAL
.....9-206,9-279
RETAINER - OPERATION, OVERRUNNING
CLUTCH CAM/OVERDRIVE PISTON
.....21-235,
21-405,21-580,21-751
RETAINER - REMOVAL, CRANKSHAFT
REAR OIL SEAL
.................9-206,9-278
RETRACTOR - INSTALLATION, REAR
SEAT BELT
.........................8O-26
RETRACTOR - REMOVAL, REAR SEAT
BELT
..............................8O-26RETRACTORS AND HEAD RESTRAINTS -
INSPECTION, SEAT BELTS, SHOULDER
BELTS .............................30-12
RETURN - DESCRIPTION, HOSES........19-37
RETURN - DESCRIPTION, SENSOR.......8E-17
RETURN - OPERATION, HOSES..........19-37
REVOLUTIONS PER MILE,
SPECIFICATIONS - TIRE................22-9
RIGHT FRONT FENDER - INSTALLATION . . 23-94
RIGHT FRONT FENDER - REMOVAL......23-94
RING - INSTALLATION, PINION
GEAR/RING GEAR/TONE.....3-105,3-137,3-166,
3-195
RING - REMOVAL, PINION GEAR/RING
GEAR/TONE..........3-103,3-135,3-165,3-193
RING FITTING - STANDARD
PROCEDURE, PISTON.........9-154,9-41,9-98
RING FITTING, PISTON RINGS -
STANDARD PROCEDURE-PISTON........9-288
RINGS - STANDARD PROCEDURE,
FITTING PISTON.....................9-211
RINGS - STANDARD PROCEDURE-
PISTON RING FITTING, PISTON.........9-288
RISER - INSTALLATION, SEAT..........23-141
RISER - REMOVAL, SEAT.............23-141
RKE TRANSMITTER BATTERIES -
STANDARD PROCEDURE...............8N-8
RKE TRANSMITTER PROGRAMMING -
STANDARD PROCEDURE...............8N-8
ROAD TEST - DIAGNOSIS AND TESTING . . . 8P-3
ROAD TEST - INSPECTION WINDSHIELD
WIPERS/WASHERS....................30-18
ROAD TEST INSPECTION - DESCRIPTION . 30-15
ROAD TESTING - DIAGNOSIS AND
TESTING........21-143,21-314,21-486,21-657
ROCKER ARM / ADJUSTER ASSEMBLY -
INSTALLATION........................9-85
ROCKER ARM / ADJUSTER ASSEMBLY -
REMOVAL...........................9-85
ROCKER ARM / ADJUSTER ASSY -
CLEANING..........................9-262
ROCKER ARM / ADJUSTER ASSY -
DESCRIPTION.......................9-261
ROCKER ARM / ADJUSTER ASSY -
INSPECTION........................9-262
ROCKER ARM / ADJUSTER ASSY -
INSTALLATION.............9-142,9-200,9-263
ROCKER ARM / ADJUSTER ASSY -
REMOVAL................9-142,9-200,9-261
ROD - CLEANING, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - CONNECTING RODS, PISTON &
CONNECTING........................9-286
ROD - DESCRIPTION, PISTON &
CONNECTING.....9-153,9-208,9-282,9-40,9-97
ROD - INSPECTION, PISTON &
CONNECTING.....9-154,9-209,9-285,9-41,9-98
ROD - INSTALLATION, PISTON &
CONNECTING.....9-154,9-210,9-287,9-41,9-98
ROD - REMOVAL, PISTON &
CONNECTING.....9-154,9-209,9-285,9-40,9-97
ROD BEARING AND CRANKSHAFT
JOURNAL CLEARANCE - STANDARD
PROCEDURE, CONNECTING............9-274
ROD BEARING FITTING - STANDARD
PROCEDURE, CONNECTING . . . 9-144,9-202,9-88
ROD BEARING FITTING, CONNECTING
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING
..............9-31
ROD BEARINGS - STANDARD
PROCEDURE-CONNECTING ROD
BEARING FITTING, CONNECTING
.........9-31
RODS, PISTON & CONNECTING ROD -
CONNECTING
........................9-286
ROLLOVER VALVE - DESCRIPTION
.......14-25
ROLLOVER VALVE - INSTALLATION
......14-27
ROLLOVER VALVE - REMOVAL
..........14-26
ROOF JOINT MOLDING - INSTALLATION
. . 23-91
ROOF JOINT MOLDING - REMOVAL
......23-91
ROTATION - STANDARD PROCEDURES,
TIRE
................................22-2
ROTOR - DIAGNOSIS AND TESTING,
DISC BRAKE
.........................5-20
ROTOR - DIAGNOSIS AND TESTING,
DISTRIBUTOR
.......................8I-13
RUN CHANNEL - INSTALLATION, GLASS
. . 23-70
RUN CHANNEL - REMOVAL, GLASS
......23-70
BR/BEINDEX 29
Description Group-Page Description Group-Page Description Group-Page