key DODGE SPRINTER 2008 2.G Owner's Guide

175 Controls in detail
Operating system with steering wheel buttons*
3
Setting the windshield wiper
sensitivityYou can use the
Wipe sensor
function to
set the sensitivity of the rain sensor.
\1
Press the
è
or
ÿ
button re-
peatedly until you see the
Vehicle

message in the display.
\1
Press the
j
or
k
button re-
peatedly until you see the
Wipe sen-
sor
message in the display.
The current setting is highlighted.
\1
Press the
æ
or
ç
button to
select the level of sensitivity of the
rain sensor.
\4
Level 1
: High sensitivity
Wiping beings in light rain
\4
Level 2
: Moderate sensitivity
\4
Level 3
: Low sensitivity
Wiping only begins in heavy rain
Convenience submenu
*
You can reach the
Convenience
submenu
via the
Settings
menu (
\2
page 161).
Key-dependent settingsYou can use the
Key
function to deter-
mine whether the settings in the:
\4
Instrument cluster
\4
Lighting
\4
Vehicle
submenus are stored as key-dependent
settings.
\1
Press the
è
or
ÿ
button re-
peatedly until you see the
Conve-
nience
message in the display. N54.32-2272-31
nf_BA.book Page 175 Friday, January 25, 2008 3:53 PM

176 Controls in detailOperating system with steering wheel buttons*
3
\1
Press the
j
or
k
button re-
peatedly until you see the
Key
mes-
sage in the display.
The current setting is highlighted.
\1
Press the
æ
or
ç
button to
switch key dependence On or
Off
.The Trip computer menu displays statis-
tical data for your vehicle. N54.32-2273-31
iFor safety reasons, it is not possible
to set the
Key
function while the vehi-
cle is in motion. You will see the fol-
lowing message in the display:
Setting only possible at stand-
still
.
Trip computer menuFunction
Page
Consumption statistics after
start
177
Consumption statistics after
reset
177
Reset consumption statistics
178
iWhen you call up the trip computer
again, it always displays the con-
sumption statistics after start first.
The units of the trip computer are
country-specific and depend on the
setting in the
Instrument
submenu of
the
Settings
menu.
Function
Page
nf_BA.book Page 176 Friday, January 25, 2008 3:53 PM

177 Controls in detail
Operating system with steering wheel buttons*
3
Consumption statistics after start
\1
Press the
è
or
ÿ
button re-
peatedly until you see the
After start
message in the display.
1Distance driven since start
2Time elapsed since start
3Average speed since start
4Average fuel consumption since start
Consumption statistics after reset
\1
Press the
è
or
ÿ
button re-
peatedly until you see the
After start
message in the display.
\1
Press the
j
or
k
button re-
peatedly until you see the
After re-
set
message.
1Distance driven since last reset
2Time elapsed since last reset
3Average speed since last reset
4Average fuel consumption since last
reset
N54.32-2274-31
iIf you turn the key to position
0 in the
ignition lock or remove it, all the val-
ues are reset after approximately 4
hours.
The values will not be reset if you turn
the key back to position
1 or
2 during
this time.
N54.32-2275-31
nf_BA.book Page 177 Friday, January 25, 2008 3:53 PM

186 Controls in detailDriving and parking
3
Starting the engine
Gasoline engine
\1
Turn the key to position
3 in the igni-
tion lock (
\2
page 111) and release it
immediately ("touch-start" function).
The engine starts automatically.
Diesel engine
\1
Switch on the ignition (
\2
page 111).
The
q
preglow indicator lamp in
the instrument cluster comes on.
\1
As soon as the
q
preglow indica-
tor lamp goes out, turn the key to po-
sition
3 in the ignition lock and
release it as soon as the engine is
running.
\1
Warm the engine up quickly.
\1
Do not run the engine at full speed
until it has reached operating tem-
perature.iYou can start the engine without pre-
glow when the engine is warm.After a cold start
Pulling awayWarning
G
Do not downshift for additional engine
braking on a slippery surface. The drive
wheels may lose their grip and the vehicle
could skid.!
CAUTION
Only drive at high speeds once the
engine has warmed up. This protects
the engine.
When driving on slippery surfaces,
avoid spinning the drive wheels
where possible as this could damage
the drive train.
nf_BA.book Page 186 Friday, January 25, 2008 3:53 PM

189 Controls in detail
Driving and parking
3
Apply the brakes so that you can feel
their response after a journey on wet
roads, especially if the road has been
salted. The brake discs will be warmed,
dry more quickly and be protected
against corrosion.
If you make only moderate use of the
service brake, check from time to time
that it is fully functional. To do this,
brake more sharply at a higher vehicle
speed. The brake will grip better as a re-
sult.For safety reasons, the manufacturer
recommends that you only have brake
pads / linings installed on your vehicle
that have been approved for the Sprinter
Vehicle.
Brake pads /linings that have not been
approved for the Sprinter Vehicle could
affect your vehicle’s operating safety.
iIn exceptional cases, the handbrake
can be used for emergency braking if
the service brake fails (
\2
page 192).
ParkingWarning
G
Only remove the key from the ignition
lock when the vehicle is stationary, since
it is not possible to steer the vehicle with
the key removed.
Always apply the handbrake after parking
the vehicle.
Never leave children unsupervised in the
vehicle. They could release the hand-
brake. This could lead to a serious or fatal
accident.
nf_BA.book Page 189 Friday, January 25, 2008 3:53 PM

190 Controls in detailDriving and parking
3
Warning
G
Always switch off the engine and apply
the handbrake before leaving the vehicle.
The vehicle could roll away if it is not
secured.
On uphill or downhill gradients steeper
than 15%:
\4apply the handbrake
\4secure an unloaded vehicle by chock-
ing the front axle (\2page 521)
\4secure a loaded vehicle by, for exam-
ple, chocking the rear axle
(\2page 521)
!
CAUTION
Whenever you park the vehicle, al-
ways remove the key to prevent the
battery from excessively discharg-
ing.
For vehicles which are out of use for
extended periods and have a battery
isolating switch*, switch off the elec-
trical system (
\2
page 338).
Warning
G
Make sure that the exhaust system does
not come into contact with highly flamma-
ble materials, e.g. dry grass or gasoline.
The flammable material could otherwise
ignite and set vehicle components on fire.
nf_BA.book Page 190 Friday, January 25, 2008 3:53 PM

193 Controls in detail
Driving and parking
3
Stopping the engine\1
Apply handbrake (
\2
page 191).
\1
Move selector lever to
P.
\1
Turn key to position
0 (\2
page 111)
in the ignition lock and remove it.
The immobilizer is activated.
\1
Secure the vehicle at the front axle if
unloaded and at the rear axle if load-
ed, e.g. using a chock (
\2
page 521).
Warning
G
The wheels on the rear axle could lock if
the handbrake lever is applied too abrupt-
ly. The vehicle could then start to skid.
Make sure that you apply the handbrake
lever carefully to ensure that braking ap-
plication is moderated.
!
CAUTION
If the coolant temperature is raised,
e.g. following driving in mountainous
terrain, run the engine at idling speed
for a further 1 or 2 minutes before
you switch off the engine. This allows
the coolant temperature to return to
normal again.
iWhen parking on steep uphill or
downhill gradients, turn the front
wheels towards the curb.
iYou can only remove the key from
the ignition lock when the selector le-
ver is in position
P.
nf_BA.book Page 193 Friday, January 25, 2008 3:53 PM

202 Controls in detailAutomatic transmission
3
The selector lever position engaged or
the current shift range is shown in the
display. Display on vehicles with steer-
ing wheel buttons* (
\2
page 151) and on
vehicles without steering wheel buttons
(
\2
page 147).
When the selector lever is in position
D,
you can influence the gearshifts made
by the automatic transmission by:
\4
restricting the shift range
\4
changing gear yourself
Selector lever positionsì

Parking lock

Prevents the parked vehicle
from rolling away. Only move
the selector lever to
P when
the vehicle is stationary.
You can only remove the key
when the selector lever is in
position
P. The selector lever
is locked in position
P when
the key is removed.
í

Reverse gear

Only move the selector lever
to
R when the vehicle is sta-
tionary.
ë

NeutralNo power is transmitted from
the engine to the drive
wheels. Releasing the brakes
will allow you to move the ve-
hicle freely, e.g. by pushing or
towing.Do not move the selector le-
ver to
N while the vehicle is in
motion. The automatic trans-
mission could otherwise be
damaged.
nf_BA.book Page 202 Friday, January 25, 2008 3:53 PM

210 Controls in detailGood visibility
3
The combination switch is located on
the left of the steering wheel.1Single wipe
2To switch the windshield wipers on
Switching on the windshield wipers
\1
Turn key to position
1 in the ignition
lock (
\2
page 111).
\1
Turn the combination switch to the
required position in the direction of
arrow
2
depending on how heavy
the rain is:
0
Windshield wipers off
I
Intermittent wipe
II
Normal wipe
III
Rapid wipe
Windshield wipers
N54.25-2923-31
!
CAUTION
Vehicles with rain sensor*:
Switch off the windshield wipers in
dry weather conditions, otherwise
dirt on the surface of the rain sensor
or optical effects can cause inadvert-
ent wiper sweeps. This could dam-
age the wiper blades or scratch the
windshield.
iCanada only:
The speed of the windshield wipers is
automatically reduced if the vehicle
comes to a halt with the windshield
wipers switched on.
nf_BA.book Page 210 Friday, January 25, 2008 3:53 PM

212 Controls in detailGood visibility
3
Intermittent wipeOnly switch on intermittent wipe in
damp weather conditions or when it is
raining.
Vehicles with rain sensor*:
The a rain sensor is activated when you
switch on intermittent wipe. The appro-
priate wiping frequency is set automati-
cally according to the rain falling on the
sensor.The switch is in the combination switch
on the left of the steering wheel.
1Switch
2To wipe with windshield washer fluid
3Intermittent wipe
4To switch off the wiper
5To wipe with windshield washer fluid
\1
Turn key to position
1 in the ignition
lock (
\2
page 111).
Switching on intermittent wipe
\1
Turn switch
1
to
3
.
Switching off intermittent wipe
\1
Turn switch
1
to
4
.
Rear window wiper*
N54.25-2924-31
iThe rear window wiper switches on
automatically if you engage reverse
gear and the windshield wipers are
on.
nf_BA.book Page 212 Friday, January 25, 2008 3:53 PM