instrument panel FIAT 500C 2018 Repair Manual
[x] Cancel search | Manufacturer: FIAT, Model Year: 2018, Model line: 500C, Model: FIAT 500C 2018Pages: 338, PDF Size: 4 MB
Page 233 of 338

SCHEDULED SERVICING
Your vehicle is equipped with an automatic oil change
indicator system. The oil change indicator system will
remind you that it is time to take your vehicle in for
scheduled maintenance.
Based on engine operation conditions, the oil change
indicator message will illuminate. This means that service
is required for your vehicle. Operating conditions such as
frequent short-trips, trailer tow, extremely hot or cold
ambient temperatures, and E85 fuel usage will influence
when the “Change Oil” or “Oil Change Required” message
is displayed. Severe Operating Conditions can cause the
change oil message to illuminate as early as 3,500 miles
(5,600 km) since last reset. Have your vehicle serviced as
soon as possible, within the next 500 miles (805 km).
Your authorized dealer will reset the oil change indicator
message after completing the scheduled oil change. If a
scheduled oil change is performed by someone other than
your authorized dealer, the message can be reset by
referring to the steps described under “Instrument Cluster
Display” in “Getting To Know Your Instrument Panel” for
further information. NOTE: Under no circumstances should oil change inter-
vals exceed 10,000 miles (16,000 km), twelve months or
350 hours of engine run time, whichever comes first. The
350 hours of engine run or idle time is generally only a
concern for fleet customers.
Severe Duty All Models
Change Engine Oil at 4,000 miles (6,500 km) if the vehicle
is operated in a dusty and off road environment or is
operated predominantly at idle or only very low engine
RPM’s. This type of vehicle use is considered Severe Duty.
Once A Month Or Before A Long Trip:
Check engine oil level.
Check windshield washer fluid level.
Check the tire inflation pressures and look for unusual
wear or damage.
Check the fluid levels of the coolant reservoir and brake
master cylinder, and fill as needed.
Check function of all interior and exterior lights. 8SERVICING AND MAINTENANCE 231
Page 286 of 338

VEHICLE IDENTIFICATION NUMBER
The Vehicle Identification Number (VIN) is found on the
left front corner of the instrument panel, visible through
the windshield. This number also appears engraved on the
right front door sill, under the sill scuff plate, on an
adhesive label applied to the right door opening on the
B-Pillar, on the vehicle registration and title.
NOTE: It is illegal to remove or alter the VIN.
Vehicle Identification Number Stamped VIN Location284 TECHNICAL SPECIFICATIONS
Page 299 of 338

NOTE:
• FCA US LLC or your dealer may contact you directly
regarding software updates.
• To help further improve vehicle security and minimize
the potential risk of a security breach, vehicle owners
should:
• Routinely check www.driveuconnect.com/support/
software-update.html (U.S. Residents) or www.driveu-
connect.ca (Canadian Residents) to learn about avail-
able Uconnect software updates.
• Only connect and use trusted media devices (e.g.
personal mobile phones, USBs, CDs).
Privacy of any wireless and wired communications cannot
be assured. Third parties may unlawfully intercept infor-
mation and private communications without your consent.
For further information, refer to “Onboard Diagnostic
System (OBD II) Cybersecurity” in “Getting To Know Your
Instrument Panel”. UCONNECT SETTINGS
The Uconnect system uses a combination of buttons on the
touchscreen and buttons on the faceplate located on the
center of the instrument panel that allows you to access
and change the customer programmable features. Many
features can vary by vehicle.
Uconnect 3/3 NAV Display Buttons On The Touchscreen
And Buttons On The Faceplate1 — Uconnect Buttons On The Touchscreen
2 — Uconnect Buttons On The Faceplate 10 MULTIMEDIA 297
Page 300 of 338

Customer Programmable Features — Uconnect 3/3
NAV Display Settings
Push the Settings button on the faceplate, to display the
settings menu screen. In this mode the Uconnect system
allows you to access programmable feature settings.
NOTE: Only one touchscreen area may be selected at a time.
When making a selection, press the button on the touch-
screen to enter the desired mode. Once in the desired
mode, press and release the preferred setting and make
your selection. Once the setting is complete, either press the back arrow button on the touchscreen or push the back
button on the faceplate to return to the previous menu.
Or press the “X” button on the touchscreen to close out of
the settings screen. Pressing the up or down arrow buttons
on the right side of the screen allows you to toggle up or
down through the available settings.
NOTE: All settings should be changed with the ignition in
the “AVV/MAR” position.
Display
After pressing the “Display” button on the touchscreen, the
following settings will be available:
Setting Name Selectable Options
Display Mode Auto Manual
NOTE:
When the “Display Mode” feature is set to “Auto” the radio touchscreen’s brightness is adjusted with all other instru-
ment panel displays and lights when they are adjusted using the instrument cluster display buttons on the right-hand
side of the instrument cluster display. When the “Display Mode” feature is set to “Manual” the radio screen brightness
can be adjusted independently using the “Brightness” feature below:
Brightness +–
Language English Español Français
Touchscreen Beep On Off298 MULTIMEDIA
Page 329 of 338

Ignition ..................................19
Switch .................................19
Immobilizer (Sentry Key) ......................21
Instrument Cluster
Descriptions .............................94
Display ................................79
Instrument Cluster ........................72
Instrument Panel Lens Cleaning ............... .282
Interior Appearance Care .................... .281
Interior Lighting ............................40
Introduction ................................4
iPod/USB/MP3 Control ..................... .308
Jack Operation ........................... .255
Jump Starting ............................ .220
Key Fob
Programming Additional Key Fobs ......... .18, 21
Key Fob Programming (Remote Keyless Entry) ......18
Key-In Reminder ............................21
Keys ....................................16
Replacement .............................21
Sentry (Immobilizer) .......................21
Lane Change And Turn Signals .................37 Lane Change Assist ...................... .37, 40
Lap/Shoulder Belts .........................116
Latches ................................. .157
Hood ..................................63
Lead Free Gasoline ........................ .287
Leaks, Fluid ............................. .157
Life Of Tires ............................. .267
Liftgate ..................................65
Liftgate (Sedan) .............................65
Light Bulbs .......................... .157, 197
Lights ............................... .38, 157
AirBag......................... .84, 124, 155
Brake Assist Warning ..................... .105
Brake Warning ...........................84
Bulb Replacement ....................... .197
Cruise .................................94
Daytime Running .........................37
Dimmer Switch, Headlight ...................37
Engine Temperature Warning .................86
Exterior .............................. .157
Headlights ..............................37
High Beam ..............................38
High Beam/Low Beam Select .................37
Instrument Cluster ........................37
Lights On Reminder .......................37 12 INDEX 327