oil FIAT 500C 2019 Owner's Guide

Brake System
In order to assure brake system performance, all brake
system components should be inspected periodically. Refer
to the “Maintenance Plan” in this section for the proper
maintenance intervals.
WARNING!
Riding the brakes can lead to brake failure and possi-
bly a collision. Driving with your foot resting or riding
on the brake pedal can result in abnormally high brake
temperatures, excessive lining wear, and possible
brake damage. You would not have your full braking
capacity in an emergency.
Brake Master Cylinder
The fluid in the master cylinder should be checked when
performing under hood services or immediately if the
“Brake Warning Light” is illuminated.
Be sure to clean the top of the master cylinder area before
removing the cap. If necessary, add fluid to bring the fluid
level up to the requirements described on the brake fluid
reservoir. With disc brakes, fluid level can be expected to
fall as the brake pads wear. Brake fluid level should bechecked when pads are replaced. However, low fluid level
may be caused by a leak and a checkup may be needed.
Use only manufacturer’s recommended brake fluid. Refer
to “Fluids And Lubricants” in “Technical Specifications”
for further information.
WARNING!
•
Use only manufacturer’s recommended brake fluid.
Refer to “Fluids And Lubricants” in “Technical
Specifications” for further information. Using the
wrong type of brake fluid can severely damage your
brake system and/or impair its performance. The
proper type of brake fluid for your vehicle is also
identified on the original factory installed hydraulic
master cylinder reservoir.
• To avoid contamination from foreign matter or mois-
ture, use only new brake fluid or fluid that has been
in a tightly closed container. Keep the master cylin-
der reservoir cap secured at all times. Brake fluid in
a open container absorbs moisture from the air
resulting in a lower boiling point. This may cause it
(Continued)
8
SERVICING AND MAINTENANCE 247

WARNING!(Continued)
to boil unexpectedly during hard or prolonged brak-
ing, resulting in sudden brake failure. This could
result in a collision.
• Overfilling the brake fluid reservoir can result in
spilling brake fluid on hot engine parts, causing the
brake fluid to catch fire. Brake fluid can also damage
painted and vinyl surfaces, care should be taken to
avoid its contact with these surfaces.
• Do not allow petroleum based fluid to contaminate
the brake fluid. Brake seal components could be
damaged, causing partial or complete brake failure.
This could result in a collision.
Manual Transmission — If Equipped
Lubricant Selection
Use only the manufacturers recommended transmission
fluid. Refer to “Fluids And Lubricants” in “Technical
Specifications” for further information.
Please see an authorized dealer for service.
Fluid Level Check
Check the fluid level by removing the fill plug. The fluid
level should be between the bottom of the fill hole and a
point not more than 3/16 inch (4.7 mm) below the bottom
of the hole.
Add fluid, if necessary, to maintain the proper level.
Please see an authorized dealer for service.
Frequency Of Fluid Change
Under normal operating conditions, the fluid installed at
the factory will give satisfactory lubrication for the life of
the vehicle. Fluid changes are not necessary unless lubri-
cant has become contaminated with water.
NOTE: If contaminated with water, the fluid should be
changed immediately.
Automatic Transmission — If Equipped
Selection Of Lubricant
It is important to use the proper transmission fluid to
ensure optimum transmission performance and life. Use
only the manufacturer’s specified transmission fluid. Refer
to “Fluids And Lubricants” in “Technical Specifications”
248 SERVICING AND MAINTENANCE

Keep dismounted tires in a cool, dry place with as little
exposure to light as possible. Protect tires from contact with
oil, grease, and gasoline.
Replacement Tires
The tires on your new vehicle provide a balance of many
characteristics. They should be inspected regularly for
wear and correct cold tire inflation pressures. The manu-
facturer strongly recommends that you use tires equivalent
to the originals in size, quality and performance when
replacement is needed. Refer to the paragraph on “Tread
Wear Indicators” in this section. Refer to the Tire and
Loading Information placard or the Vehicle Certification
Label for the size designation of your tire. The Load Index
and Speed Symbol for your tire will be found on the
original equipment tire sidewall.
See the Tire Sizing Chart example found in the “Tire Safety
Information” section of this manual for more information
relating to the Load Index and Speed Symbol of a tire.
It is recommended to replace the two front tires or two rear
tires as a pair. Replacing just one tire can seriously affect
your vehicle’s handling. If you ever replace a wheel, make
sure that the wheel’s specifications match those of the
original wheels.It is recommended you contact an authorized tire dealer or
original equipment dealer with any questions you may
have on tire specifications or capability. Failure to use
equivalent replacement tires may adversely affect the
safety, handling, and ride of your vehicle.
WARNING!
•
Do not use a tire, wheel size, load rating, or speed
rating other than that specified for your vehicle.
Some combinations of unapproved tires and wheels
may change suspension dimensions and perfor-
mance characteristics, resulting in changes to steer-
ing, handling, and braking of your vehicle. This can
cause unpredictable handling and stress to steering
and suspension components. You could lose control
and have a collision resulting in serious injury or
death. Use only the tire and wheel sizes with load
ratings approved for your vehicle.
• Never use a tire with a smaller load index or capacity,
other than what was originally equipped on your
vehicle. Using a tire with a smaller load index could
result in tire overloading and failure. You could lose
control and have a collision.
(Continued)
8
SERVICING AND MAINTENANCE 263

Replace the belts if they appear frayed or worn or if the
buckles do not work properly.
WARNING!
A frayed or torn belt could rip apart in a collision and
leave you with no protection. Inspect the belt system
periodically, checking for cuts, frays, or loose parts.
Damaged parts must be replaced immediately. Do not
disassemble or modify the system. Seat belt assemblies
must be replaced after a collision if they have been
damaged (i.e., bent retractor, torn webbing, etc.).
Plastic And Coated Parts
Use Mopar Total Clean to clean vinyl upholstery.
CAUTION!
•Direct contact of air fresheners, insect repellents,
suntan lotions, or hand sanitizers to the plastic,
painted, or decorated surfaces of the interior may
cause permanent damage. Wipe away immediately.
• Damage caused by these type of products may not be
covered by your New Vehicle Limited Warranty.
Cleaning Plastic Instrument Cluster Lenses
The lenses in front of the instruments in this vehicle are
molded in clear plastic. When cleaning the lenses, care
must be taken to avoid scratching the plastic.
1. Clean with a wet soft cloth. A mild soap solution may be used, but do not use high alcohol content or abrasive
cleaners. If soap is used, wipe clean with a clean damp
cloth.
2. Dry with a soft cloth.
Leather Parts
Mopar Total Clean is specifically recommended for leather
upholstery.
Your leather upholstery can be best preserved by regular
cleaning with a damp soft cloth. Small particles of dirt can
act as an abrasive and damage the leather upholstery and
should be removed promptly with a damp cloth. Stubborn
soils can be removed easily with a soft cloth and Mopar
Total Clean. Care should be taken to avoid soaking your
leather upholstery with any liquid. Please do not use
polishes, oils, cleaning fluids, solvents, detergents, or
ammonia-based cleaners to clean your leather upholstery.
Application of a leather conditioner is not required to
maintain the original condition.8
SERVICING AND MAINTENANCE 277

In the event power assist is lost for any reason (i.e.,
repeated brake applications with the engine OFF) the
brakes will still function. However, the effort required to
brake the vehicle will be much greater than that required
with the power system operating.
WHEEL AND TIRE TORQUE SPECIFICATIONS
Proper lug nut/bolt torque is very important to ensure that
the wheel is properly mounted to the vehicle. Any time a
wheel has been removed and reinstalled on the vehicle, the
lug nuts/bolts should be torqued using a properly cali-
brated torque wrench using a high quality six sided (hex)
deep wall socket.
Torque Specifications
Lug Nut/Bolt Torque **Lug Nut/Bolt SizeLug Nut/
Bolt Socket Size
66 Ft-Lbs (90 N·m)
Steel Wheels Only
74 Ft-Lbs (100 N·m) Aluminum Wheels Only M12 x 1.25 17 mm **Use only your authorized dealer recommended lug nuts/
bolts and clean or remove any dirt or oil before tightening.
Inspect the wheel mounting surface prior to mounting the
tire and remove any corrosion or loose particles.
Tighten the lug nuts/bolts in a star pattern until each
nut/bolt has been tightened twice.
Wheel Mounting Surface
9
TECHNICAL SPECIFICATIONS 281

FLUID CAPACITIES
U.S.Metric
Fuel (Approximate) 10.5 Gallons40 Liters
Engine Oil with Filter
1.4 Liter Turbo Engine 4 Quarts3.8 Liters
Cooling System
1.4 Liter Turbo Engine (Mopar Antifreeze/Engine Coolant 10
Year/150,000 Mile (240,000 km) Formula) — with Manual Trans-
mission 4.6 Quarts
4.4 Liters
1.4 Liter Turbo Engine (Mopar Antifreeze/Engine Coolant 10
Year/150,000 Mile (240,000 km) Formula) — with Automatic
Transmission 5.8 Quarts
5.5 Liters
286 TECHNICAL SPECIFICATIONS

FLUIDS AND LUBRICANTS
Engine
ComponentFluid, Lubricant, or Genuine Part
Engine Coolant – 1.4L Turbo Engine We recommend you use Mopar Antifreeze/Coolant 10 Year/150,000
Mile (240,000 km) Formula OAT (Organic Additive Technology)
meeting the requirements of FCA Material Standard MS-90032.
Engine Oil – 1.4L Turbo Engine We recommend you use API Certified SAE 5W-40 Full Synthetic
Engine Oil, meeting the requirements of FCA Material Standard
MS-12991. Refer to your engine oil filler cap for correct SAE grade.
Engine Oil Filter – 1.4L Turbo Engine We recommend you use a Mopar Engine Oil Filter.
Spark Plugs – 1.4L Turbo Engine We recommend you use Mopar Spark Plugs.
Fuel Selection – 1.4L Turbo Engine 91 Octane Recommended – 87 Octane Acceptable,
0-15% Ethanol.
CAUTION!
•Mixing of engine coolant (antifreeze) other than speci-
fied Organic Additive Technology (OAT) engine coolant
(antifreeze), may result in engine damage and may
decrease corrosion protection. Organic Additive Tech-
nology (OAT) engine coolant is different and should not
(Continued)
CAUTION! (Continued)
be mixed with Hybrid Organic Additive Technology
(HOAT) engine coolant (antifreeze) or any “globally
compatible” coolant (antifreeze). If a non-OAT engine
coolant (antifreeze) is introduced into the cooling sys-
tem in an emergency, the cooling system will need to be
drained, flushed, and refilled with fresh OAT coolant
(Continued)
9
TECHNICAL SPECIFICATIONS 287

Autostick............................... .174
Battery .............................. .87, 231
Charging System Light .....................87
Jump Starting .......................... .213
Belts, Seat ............................... .155
Body Mechanism Lubrication ..................238
B-Pillar Location .......................... .254
Brake Assist System ........................ .101
Brake Fluid .......................... .287, 288
Brake, Parking ............................ .163
Brake System ......................... .247, 280
Anti-Lock (ABS) ..................... .100, 280
Fluid Check ........................... .247
Master Cylinder ........................ .247
Parking .............................. .163
Warning Light ...........................86
Brake/Transmission Interlock ..................168
Bulb Replacement ......................... .196
Bulbs, Light .......................... .157, 196
Camera, Rear ............................ .185
Capacities, Antifreeze (Engine Coolant) ...........286
Capacities, Fluid .......................... .286Caps, Filler
Fuel ................................. .186
Oil (Engine) ........................... .233
Radiator (Coolant Pressure) .................245
Carbon Monoxide Warning ................154, 285
Car Washes .............................. .274
Cellular Phone ........................... .302
Certification Label ......................... .188
Chains, Tire ............................. .269
Changing A Flat Tire ....................... .250
Check Engine Light (Malfunction Indicator Light) ....97
Checking Your Vehicle For Safety ...............154
Checks, Safety ............................ .154
Child Restraint ........................... .138
Child

Restraints
Booster Seats ........................... .141
Child Seat Installation .....................151
How To Stow An unused ALR Seat Belt ........148
Infant And Child Restraints .................140
Lower Anchors And Tethers For Children .......143
Older Children And Child Restraints ...........140
Seating Positions ........................ .142
Clean Air Gasoline ........................ .283
Cleaning Wheels ............................... .268
12
INDEX 317

Climate Control............................44
Automatic ........................... .49, 54
Manual ................................45
Compact Disc (CD) Maintenance ................308
Compact Spare Tire ........................ .266
Contract, Service .......................... .312
Convertible Top Maintenace ...................275
Coolant (Antifreeze) .....................286, 287
Cooling Pressure Cap (Radiator Cap) ............245
Cooling System ........................... .242
Adding Coolant (Antifreeze) .................244
Coolant Level ....................... .242, 245
Cooling Capacity ........................ .287
Disposal Of Used Coolant ..................245
Drain, Flush, And Refill ....................243
Inspection ............................. .245
Points To Remember ..................... .246
Pressure Cap ........................... .245
Radiator Cap .......................... .245
Selection Of Coolant (Antifreeze) .............243
Corrosion Protection ....................... .273
Cruise Control (Speed Control) .................177
Cruise Light ........................... .95, 96
Cupholders ...............................68
Customer Assistance ....................... .310Customer Programmable Features
...............291
Cybersecurity ............................ .290
Daytime Running Lights ....................37, 38
Dealer Service ............................ .232
Defroster, Windshield ....................... .155
Diagnostic System, Onboard ....................96
Dimmer Switch Headlight ...............................37
Dipsticks Oil (Engine) ........................... .230
Disposal Antifreeze (Engine Coolant) .................245
Door Ajar ............................. .87,
89
Door Ajar Light ......................... .87, 89
Doors ....................................24
Driver ’s Seat Back Tilt ........................26
Driving Through Flowing, Rising, Or Shallow Standing
Water ................................ .192
Electrical Power Outlets .......................69
Electric Brake Control System ..................101
Electric Remote Mirrors .......................36
Electronic Stability Control (ESC) ...............103
318 INDEX

Electronic Throttle Control Warning Light..........88
Emergency, In Case Of Hazard Warning Flasher ...................196
Jacking ............................... .250
Jump Starting .......................... .213
Towing ............................... .219
Emission Control System Maintenance ............97
Engine Air Cleaner ............................ .234
Break-In Recommendations .................163
Checking Oil Level ...................... .230
Compartment .......................... .229
Cooling .............................. .242
Exhaust Gas Caution ...................154, 285
Fails To Start ........................... .162
Flooded, Starting ........................ .162
Fuel Requirements ....................282, 287
Oil .............................. .232, 286
Oil Filler Cap .......................... .233
Oil Filter .............................. .234
Oil Reset ...............................84
Oil Selection ........................ .232, 287
Oil Synthetic ........................... .233
Overheating ........................... .216
Starting .............................. .161Enhanced Accident Response Feature
.........133, 221
Ethanol ................................. .283
Exhaust Gas Cautions ....................154, 285
Exhaust System ....................... .154, 241
Exterior Lighting ............................37
Exterior Lights ...................... .37, 157, 196
Filters Air Cleaner ............................ .234
Air Conditioning ..................... .57, 236
Engine Fuel ........................... .287
Engine Oil ............................ .234
Engine Oil Disposal ...................... .234
Flashers Turn Signals ...................... .37,
95, 157
Flash-To-Pass ..............................37
Flooded Engine Starting ..................... .162
Fluid, Brake ............................. .288
Fluid Capacities ........................... .286
Fluid Leaks .............................. .157
Fluid Level Checks Brake ................................ .247
Engine Oil ............................ .230
Fluids .................................. .287
Fluids And Lubricants ...................... .287
12
INDEX 319