check engine FIAT BRAVO 2008 2.G User Guide
[x] Cancel search | Manufacturer: FIAT, Model Year: 2008, Model line: BRAVO, Model: FIAT BRAVO 2008 2.GPages: 246, PDF Size: 4.01 MB
Page 148 of 246
147
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
GENERIC FAILURE
INDICATION
(amber)
Inertial fuel cut-off switch
intervened
The warning light (or the symbol on dis-
play) comes on when the inertial fuel cut-
off switch is triggered.
The display will show the dedicated mes-
sage.
Engine oil pressure sensor failure
The warning light (or the symbol on the
display) turns on when a fault is detected
to engine oil pressure sensor.
Twilight sensor failure
The warning light (or the symbol on dis-
play) turns on when a fault is detected to
the twilight sensor.
The display will show the dedicated mes-
sage.
Speed limit exceeded
(only for Arabic countries)
The warning light (amber), or symbol on
the display (red), comes on when a speed
of 120 km/h is exceeded.
è
DIESEL PARTICULATE
FILTER CLOGGED
(amber)
(Multijet versions)
Turning the ignition key to MARthe
warning light turns on, but it should go off
after few seconds. The warning light turns
on when the diesel particulate filter is
clogged and the driving conditions do not
enable to activate automatically the re-
claiming procedure.
To enable the cleaning procedure, keep
the car running until the warning light
turns off.
The display will show the dedicated mes-
sage.
h
Rain sensor failure
The warning light (or the symbol on the
display) on the dial turns on when the rain
sensor is faulty. Contact Fiat Dealership.
The display will show the dedicated mes-
sage.
Parking sensors failure
(where provided)
The warning light (or the symbol on the
display) when a fault is detected to park-
ing sensors.
Tyre pressure monitoring
system failure (where provided)
The warning light (or the symbol on the
display) turns on when a failure is detect-
ed in the T.P.M.S. system (where provid-
ed).
Should one or more wheels without sen-
sor be fitted, the instrument panel warn-
ing light will come on and stay on until
restoring initial conditions.
The display will show the dedicated mes-
sage.
NOTE When one of the above faults oc-
curs, contact your Fiat Dealership as soon
as possible.FUEL RESERVE
(amber)
Turning the ignition key to
MARthe warning light turns on,
but it should go off after few seconds. The
warning light turns on when about 8 litres
fuel are left in the tank.
IMPORTANT The warning light flashes to
indicate a failure, contact Fiat Dealership
as soon as possible to have the system
checked.
ç
141-154 BRAVO GB 29-10-2008 12:32 Pagina 147
Page 149 of 246
HILL HOLDER FAILURE
(amber)
The symbol
*will turn on
when the Hill Holder system is
faulty. Contact Fiat Dealership
as soon as possible.
On certain versions warning
light
áturns on as an alternative.
The display will show the dedicated mes-
sage.
148
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
EOBD/INJECTION
SYSTEM FAILURE
(amber)
Under normal conditions, turning
the ignition key to MAR, the warning light
turns on, but it should go off when the en-
gine has started.
If the warning light stays on or turns on
when travelling, means a fault in the sup-
ply/ignition system which could cause high
emissions at the exhaust, possible lack of
performance, poor handling and high con-
sumption levels.
The display will show the dedicated mes-
sage.
In these conditions it is possible to con-
tinue driving without however requiring
heavy effort or high speed from the en-
gine. Prolonged use of the car with the
warning light on may cause damages. Con-
tact Fiat Dealership as soon as possible.
The warning light turns off if the fault dis-
appears, but it is still stored by the system.
U
If, turning the ignition key to
MAR, the warning light Udoes not turn on or if it turns
on glowing steadily or flashing
when travelling (on certain versions to-
gether with the message on the dis-
play), contact Fiat Dealership as soon
as possible. Warning light
Uoperation
can be checked by traffic agents by
proper equipment. Comply with laws
and regulations of the country where
you are driving.
Petrol engines only
Warning light turning on flashing indicates
the possibility of damage to the catalyst.
If the light flashes, it is necessary to release
the accelerator pedal to lower the speed
of the engine until the warning light stops
flashing; continue the journey at moder-
ate speed, trying to avoid driving condi-
tions that may cause further flashing and
contact Fiat Dealership as soon as possi-
ble.ESP SYSTEM
(amber)
Turning the ignition key to
MARthe warning light turns on,
but it should go off after few seconds.
If the warning light does not turn off or
stays on when travelling together with the
button led ASR, contact Fiat Dealership.
On certain versions the dedicated mes-
sage is displayed.
Warning light flashing when driving indi-
cates that the ESP system is active.
á
á
*
141-154 BRAVO GB 29-10-2008 12:32 Pagina 148
Page 151 of 246
150
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
WARNING
LIGHTS AND
MESSAGES
EBD SYSTEM
FAILURE
(red)
(amber)
The turning on at the same time of warn-
ing lights
xand >with the engine run-
ning indicates an EBD system failure or
that the system is unavailable; in this case
heavy braking may cause the rear wheels
to lock before time, with the possibility of
skidding.
Drive with the utmost care to the near-
est Fiat Dealership to have the system
checked.
The display will show the dedicated mes-
sage.
x>
CAR PROTECTION
SYSTEM FAILURE -
FIAT CODE
(amber)
ALARM FAILURE
(where provided)
(amber)
THEFT ATTEMPT
(amber)
Car protection system failure -
Fiat Code
Turning the key to MARthe warning light
shall flash only once and then go off.
The turning on of the warning light (or the
symbol on the display) glowing steadily,
with the ignition key at MAR, indicates a
probable failure (see “Fiat Code system”
in section “Dashboard and controls”).
The display will show the dedicated mes-
sage.
IMPORTANT The turning on at the same
time of warning lights
Uand Y(or sym-
bol on display) indicates a failure of the Fi-
at CODE system.
Y
If with the engine running the warning lightYflashes, this means that the car is not
protected by the engine immobilising de-
vice (see “Fiat Code system” in section
“Dashboard and controls”).
Contact Fiat Dealership to have all the
keys memorised.
Alarm failure (where provided)
The turning on of the warning light (or
symbol on display) indicates a failure in the
alarm system. Contact Fiat Dealership as
soon as possible.
The display will show the dedicated mes-
sage.
Theft attempt
The turning on of the warning light (or
symbol on display) indicates an attempt of
break-in. Contact Fiat Dealership as soon
as possible.
The display will show the dedicated mes-
sage.
141-154 BRAVO GB 29-10-2008 12:32 Pagina 150
Page 167 of 246
166
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
IN AN
EMERGENCY
FOR CHECKING AND
RESTORING PRESSURE ONLY
The compressor can be also used just for
restoring pressure. Disconnect the quick
connection and connect it directly to the
tyre valve fig. 16; in this way the cylinder
is not connected to compressor and the
sealing fluid will not flow into the tyre. CYLINDER REPLACEMENT
PROCEDURE
To replace the cylinder proceed as fol-
lows:
❒disconnect connection B-fig. 17;
❒turn counter-clockwise the cylinder to
replace and raise it;
❒fit the new cylinder and turn it clock-
wise;
❒connect connection Bto the cylinder
and fit the transparent tube Ainto the
proper space.
fig. 16F0Q0517mfig. 17F0Q0512m
❒if at least 1.8 bar pressure is read, re-
store proper pressure (with engine
running and handbrake on) and restart;
❒drive with the utmost care to the near-
est Fiat Dealership.
It is of vital importance to
communicate that the tyre
has been repaired using the quick tyre
repair kit. Hand the instruction
brochure to the personnel charged
with treating the tyre repaired with
the kit.
WARNING
If the pressure falls below 1.8
bars, do not drive any fur-
ther: the quick tyre repair kit Fix & Go
automatic cannot guarantee proper
hold because the tyre is too much
damaged. Contact Fiat Dealership.
WARNING
155-190 BRAVO GB 29-10-2008 12:35 Pagina 166
Page 194 of 246
193
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
SERVICE SCHEDULE
1.4 16V - 1.4 T-JET - 1.9 Multijet 8V - 1.9 Multijet 16V VERSIONS
30 60 90 120 150 180
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●●●
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●●●
●●
●●
●●
●●●
Thousands of km
Check tyre conditions/wear and adjust pressure if necessary
Check lighting system operation (headlights, direction indicators,
hazard lights, luggage compartment lights, passenger
compartment lights, glove compartment lights, instrument
panel warning lights, etc.)
Check operation of windscreen wiper system and
adjust sprays if necessary
Check position/wear of front/rear windscreen wiper blades
Check condition and wear of front disc brake pads and
operation of pad wear indicator
Check conditions and wear of rear disc brake pads
Visually check that the following are in good condition
and intact: body exterior, under body protection,
pipe rigid and flexible sections (exhaust-fuel system-brakes),
rubber parts (gaiters, sleeves, bushes, etc.)
Check cleanliness of locks, bonnet, engine and boot,
clean and lubricate linkages
Check and top-up fluids (hydraulic brakes/clutch,
windscreen washer, battery, engine coolant, etc.)
Check and adjust handbrake lever travel
Check visually conditions of auxiliary drive belt/s
Visually check conditions of toothed timing belt
(1.4 16V, 1.4 T-JET,1.9 Multijet 8V versions)
Check tension and adjust auxiliary drive belt
(except for engines with automatic tensioners)
Check and adjust tappet clearance (1.9 Multijet 8V version)
191-212 BRAVO GB 29-10-2008 12:33 Pagina 193
Page 195 of 246
194
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Thousands of km
Check exhaust emissions (petrol versions)
Check emissions/fumes (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Check operation of engine control systems
(by means of test interface)
Replace accessory drive belt/s
Replace toothed timing belt (petrol versions) (*)
Replace toothed timing belt (1.9 Multijet 8Vversions) (*)
Replace toothed timing belt (1.9 Multijet 16Vversions) (*)
Replace spark plugs (petrol versions)
Replace fuel filter (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace air filter cartridge (petrol versions)
Replace air filter cartridge (1.9 Multijet 8V - 1.9 Multijet 16V versions)
Replace engine oil and oil filter (petrol versions)
(or every 24 months)
Change engine oil and oil filter (
1.9 Multijet 8V - 1.9 Multijet 16V
versionswithout DPF) (or every 24 months)
Change engine oil and oil filter
(1.9 Multijet 8V - 1.9 Multijet 16V versionswith DPF) (**)
Change brake fluidr (or every 24 months)
Change pollen filter (or every 15 months)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town use, long
periods idling) or at least every 5 years.
(**) The engine oil and oil filter should be changed depending on their actual condition, which is indicated by a warning light/message on the control panel or at
least every 2 years.
For 1.4 T-JET versions, in order to ensure correct operation and avoid significant damages to the engine, it is mandatory:
- to use spark plugs specifically certified for the T-JET engine only, of the same type and brand (see paragraph “Engine”);
- to replace the plugs as often as required by the Programmed Maintenance Plan;
- we recommend to refer to the Fiat Dealership.
If the car is used mainly on urban routes or if the yearly kilometres travelled are less than 10,000 km, the engine oil and filter must be changed every 12 months.
30 60 90 120 150 180
●● ● ●● ●
●● ● ●● ●
●● ● ●● ●
●
●
●
●
●● ● ●● ●
●●●
●●●
●●●
●● ● ●● ●
●● ● ●● ●
●●●
●●●
●●●●●●
191-212 BRAVO GB 29-10-2008 12:33 Pagina 194
Page 196 of 246
195
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
1.6 Multijet and 2.0 Multijet VERSIONS
Thousands of km
Check tyre conditions/wear and adjust pressure if necessary
Check lighting system operation (headlights, direction indicators,
hazard lights, luggage compartment lights, passenger compartment lights,
glove compartment lights, instrument panel warning lights, etc.)
Check operation of windscreen wiper system and
adjust sprays if necessary
Check position/wear of front/rear windscreen wiper blades
Check condition and wear of front disc brake pads and operation
of pad wear indicator
Check conditions and wear of rear disc brake pads
Visually check that the following are in good condition
and intact: body exterior, under body protection,
pipe rigid and flexible sections (exhaust-fuel system-brakes),
rubber parts (gaiters, sleeves, bushes, etc.)
Check cleanliness of locks, bonnet, engine and boot,
clean and lubricate linkages
Check and top-up fluids (hydraulic brakes/clutch,
windscreen washer, battery, engine coolant, etc.)
Check and adjust handbrake lever travel
Check visually conditions of auxiliary drive belt/s35 70 105 140 175
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●●● ●
●●
191-212 BRAVO GB 29-10-2008 12:33 Pagina 195
Page 197 of 246
196
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
Thousands of km
Check emissions/fumes
Check operation of engine control systems
(by means of test interface)
Replace accessory drive belt/s
Replace toothed timing belt (*)
Replace fuel filter
Replace air filter cartridge
Change engine oil and oil filter (versions without DPF)
(or every 24 months)
Change engine oil and oil filter (versions with DPF) (**)
Change brake fluid (or every 24 months)
Change pollen filter (or every 15 months)
(*) Irrespective of mileage, the timing drive belt must be replace every 4 years for heavy duty applications, cold climates, town
use, long periods idling) or at least every 5 years.
(**) The engine oil and oil filter should be changed depending on their actual condition, which is indicated by a warning light/mes-
sage on the control panel or at least every 2 years.35 70 105 140 175
●●●●●
●●●●●
●
●
●●
●●
●●●●●
●●
●●●●●
191-212 BRAVO GB 29-10-2008 12:33 Pagina 196
Page 198 of 246
197
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
ROUTINE
MAINTENANCE
Every 1,000 km or before long journeys,
check and top up if required:
❒engine coolant fluid level;
❒brake fluid level;
❒windscreen washer fluid level;
❒tyre pressure and conditions;
❒light system operation (headlights, di-
rection indicators, hazard lights, etc.);
❒windscreen wiper/washer operation
and windscreen/rear window blade
position/wear;
Every 3,000 km check and top up if re-
quired: engine oil level.
You are recommended to use FL Sele-
nia, products, designed and produced
specifically for Fiat cars (see table “Ca-
pacities” in section “Technical specifica-
tions”).
HEAVY-DUTY
Should prevailing use of the car be under
one of the following specially heavy con-
ditions:
❒trailer or caravan towing;
❒dusty roads;
❒short distances (less than 7-8 km) re-
peated and with external tempera-
tures below zero;
❒frequently idling engines or long dis-
tance low speed driving (e.g. door-to-
door deliveries) or in case of a long
term inactivity;
❒driving in the city;
carry out the following checks more fre-
quently than required in the Service
Schedule:
❒check front disk brake pad conditions
and wear;
❒check cleanness of locks, bonnet and
boot and lever cleanness and lubrica-
tion;
❒sight inspect the conditions of: engine,
gearbox, transmission, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.);
❒check battery charge and fluid level
(electrolyte) (only to be carried out by
skilled personnel or at Fiat Dealership
– see also paragraph “Battery” in this
section);
❒visual check on various drive belt con-
ditions;
❒check and replace pollen filter, if re-
quired;
❒check and replace air cleaner, if re-
quired.
191-212 BRAVO GB 29-10-2008 12:33 Pagina 197
Page 199 of 246
When topping up take care
not to confuse the various
types of fluids: they are all in-
compatible with one another
and could seriously damage the car.
198
SAFETY
DEVICES
CORRECT USE
OF THE CAR
WARNING
LIGHTS AND
MESSAGES
IN AN
EMERGENCY
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
CAR
MAINTENANCE
CHECKING
FLUID LEVELS
1 Engine oil - 2 Battery - 3 Brake fluid
4 Windscreen/rear window/headlight wash-
er fluid - 5 Engine coolant
F0Q0616mfig. 1 - 1.4 16V version
F0Q0024mfig. 2 - 1.4 T-JET version
Never smoke while working
in the engine compartment;
gas and inflammable vapours may be
present, with the risk of fire.
WARNING
191-212 BRAVO GB 29-10-2008 12:33 Pagina 198