bulb FIAT CROMA 2008 2.G User Guide
[x] Cancel search | Manufacturer: FIAT, Model Year: 2008, Model line: CROMA, Model: FIAT CROMA 2008 2.GPages: 258, PDF Size: 5.86 MB
Page 179 of 258
178
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
NUMBER PLATE LIGHT fig. 36
To change the bulb, proceed as follows:
❒work in the point shown by the arrow
and remove lens A;
❒change the bulb Breleasing it from the
side contacts and making sure the new
bulb is correctly fastened between the
contacts;
❒refit the lens.
IF AN INTERIOR LIGHT
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
fig. 36F0L0079mfig. 37F0L0086m
FRONT CEILING LIGHT
fig. 37-38
To change the bulb, proceed as follows:
❒work in the points shown by the ar-
rows and remove cover A;
❒turn the 2 bulb holders Bcounter-
clockwise, remove and replace bulbs;
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 178
Page 180 of 258
179
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
COURTESY MIRROR LIGHT
fig. 39
To change the bulb, proceed as follows:
❒open the mirror cover A;
❒remove the bulb Blevering in the
points shown by the arrows;
❒replace the bulb releasing it from the
side contacts making sure that the new
bulb is correctly clamped between the
contacts.GLOVEBOX LIGHT fig. 40
To change the bulb, proceed as follows:
❒open the glovebox, remove the light
unit Alevering in the point shown by
the arrow;
❒replace the bulb releasing it from the
side contacts making sure that the new
bulb is correctly clamped between the
contacts.
❒to replace the bulb C, release it from
the side contacts making sure that the
new bulb is correctly clamped be-
tween the contacts.
fig. 38F0L0087mfig. 39F0L0088mfig. 40F0L0202m
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 179
Page 181 of 258
180
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
❒open the protection B-fig. 42and re-
place the snap-fitted bulb;
❒re-close the protective cover B-
fig. 42on the transparent;
❒refit the light unit A-fig. 41inserting
it in its correct position firstly on one
end and then on the other until it
clicks into place.PUDDLE / DOOR LIGHTS fig. 43
To change the bulb, proceed as follows:
❒open the door and remove the trans-
parent cover Alevering in the point
shown by the arrow;
❒open the protection Band replace the
snap-fitted bulb;
❒re-close the protective cover Bon the
transparent cover A. BOOT LIGHT
To change the bulb, proceed as follows:
❒open the tailgate;
❒remove the light unit A-fig. 41lever-
ing in the point shown by the arrow.
fig. 41F0L0089mfig. 42F0L0090mfig. 43F0L0180m
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 180
Page 182 of 258
181
WARNING
LIGHTS AND
MESSAGES
CAR
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
DASHBOARD
AND CONTROLS
SAFETY
DEVICES
CORRECT USE
OF THE CAR
IN AN
EMERGENCY
SIDE REAR CEILING LIGHTS
fig. 44
To change the bulb, proceed as follows:
❒remove the light unit Alevering in the
point shown by the arrow;
❒replace the bulb Breleasing it from
the side contacts making sure that the
new bulb is correctly clamped be-
tween the contacts.
fig. 45F0L0092m
If a fuse switches off again,
contact the Fiat Service Net-
work .
WARNING
fig. 44F0L0091m
IF A FUSE BLOWS
GENERAL fig. 45
The fuse is a protective device for the
electric system: it comes into action (i.e.
it cuts off) mainly due to a fault or im-
proper action on the system.
When a device does not work, check the
efficiency of its fuse: the conductor ele-
ment Amust be intact. If not, replace the
fuse with one of the same amp rating
(same colour).
Bundamaged fuse
Cfuse with damaged filament.
To replace a fuse, use the pliers Dhooked
to the fusebox on the dashboard.
157-192 Croma TRW GB 10-11-2008 13:15 Pagina 181