brake light FORD AEROSTAR 1996 1.G Owners Manual

62
*
[ST02900(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02950(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%*
[ST03000(ALL)02/95]
Removing the Key From the Ignition
*
[ST03400(ALL)06/95]
1. Put the gearshift in P (Park).
*
[ST03500(ALL)03/91]
2. Set the parking brake fully before removing
your foot from the service brake. (This will
avoid ªbindingº or ªloadingº the park gear
if you park on a grade.)
*
[ST03600(ALL)03/95]
3. Turn the ignition key to LOCK.
*
[ST03700(ALL)03/95]
4. Remove the key.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995

64
*
[ST05150(ALL)03/95]
Starting Your Vehicle
%*
[ST05200(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05300(ALL)07/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST05400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05500(ALL)08/95]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST05600(ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[ST05750(ALL)03/95]
3. Make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
*
[ST06015(ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
%*
[ST06200(ALL)02/95]
Starting Your Engine
*
[ST06300(ALL)06/95]
To start your engine:
*
[ST06400(ALL)05/95]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[ST06425(ALL)03/95]
2. Turn the ignition key to the ON position.
*
[ST06451(ALL)06/95]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995

65
*
[ST06475(ALL)02/95]
4. Turn the key to the START position
(cranking) until the engine starts. Allow the
key to return to the ON position after the
engine has started.
*
[ST06501(ALL)02/95]
If you have difficulty in turning the key,
rotate the steering wheel slightly because it
may be binding.
%*
[ST06505(ALL)04/95]
For a cold engine:
*
[ST06510(ALL)06/95]
q
At temperatures10ÊF (-12ÊC) andbelow:If
the engine does not start infifteen (15)
secondson the first try, turn the key to OFF,
wait approximately ten (10) seconds so you
do not flood the engine, then try again.
*
[ST06515(ALL)04/95]
q
At temperaturesabove10ÊF(-12ÊC):If the
engine does not start infive (5) secondson
the first try, turn the key to OFF, wait
approximately ten (10) seconds so you do not
flood the engine, then try again.
%*
[ST06530(ALL)05/95]
For a warm engine:
*
[ST06551(ALL)04/95]
q
Do not hold the key in the START position
for more thanfive (5) secondsat a time. If
the engine does not start within five (5)
seconds on the first try, turn the key to the
OFF position. Wait a few seconds after the
starter stops, then try again.
*
[ST06575(ALL)08/95]
Whenever you start your vehicle, release the key
as soon as the engine starts. Excessive cranking
could damage the starter.
*
[ST06601(ALL)08/95]
After you start the engine let it idle for a few
seconds before driving away. Keep your foot on
the brake pedal and put the gearshift lever in
gear. Release the parking brake. Slowly release
the brake pedal and drive away in the normal
manner.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995

75
%*
[LG03000(ALL)06/94]
The Mechanical Cluster
*
[LG03100(ALL)06/93]
The following warning lights and gauges are on
the mechanical cluster. All of the warning lights
and gauges alert you to possible problems with
your vehicle. Some of the lights listed are
optional. The following sections detail what each
of these indicators means.
%*
[LG03200(ALL)06/95]
Brake System Warning Light
*
[LG03300(ALL)03/95]
The warning light for the brakes can show two
things Ð that the parking brake is not fully
released, or that the brake fluid level is low in
the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by
your dealer or a qualified service technician.
*
[LG03400(ALL)05/94]
This light comes on when you turn the ignition
key to START to verify that the indicator bulb is
working. If the light stays on or comes on after
you have released the parking brake fully, have
the hydraulic brake system serviced.
*
[LG03500(ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
[LG03600(ALL)07/95]
one inch art:0095034-A
Brake warning light symbol
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995

76 [LG03700(ALL)07/95]Rear Anti-Lock (ABS) Brake Warning Light
[LG03900(ALL)05/95]
To check the rear ABS brake warning light turn
the ignition key to the ON position. The rear
ABS brake warning light should glow
momentarily.
*
[LG03950(ALL)06/94]
NOTE: If it does not glow momentarily, have
your vehicle's electrical system checked
immediately.
[LG03975(ALL)07/95]
NOTE: If the rear ABS brake warning light
begins to flash in a repeating flash
sequence, check the rear anti-lock
brake system continuous power fuse
and brake lights for proper operation.
[LG04000(ALL)05/95]
one inch art:0095035-A
Rear anti-lock warning light symbol
*
[LG04100(ALL)05/95]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[LG04110(ALL)07/95]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995

113
%*
[SC05510(ALL)03/95]
Hazard Flasher
*
[SC05520(ALL)04/95]
The hazard flasher is used to alert other drivers
to hazardous situations.
*
[SC05525(ALL)10/92]
The flashers will continue to flash with the brake
pedal depressed.
*
[SC05530(ALL)08/95]
The flashers work whether your vehicle is
running or not. The flashers work for up to two
hours when the battery is fully charged and in
good condition without draining the battery
excessively. If the flashers run for longer than
two hours or if the battery is not fully charged,
the battery power can be drained.
*
[SC05540(ALL)09/93]
To use the hazard flasher:
*
[SC05550(ALL)10/92]
1. Push in the flasher button; it will pop out
and the lamps will begin to flash.
*
[SC05560(ALL)10/92]
2. To stop the flashers, push in the flasher
button again.
*
[SC05562(ALL)08/95]
NOTE: The flasher button will be sticking up
slightly higher when on than when off.
[SC05575(ALL)08/95]
one quarter page art:0095077-A
Hazard flasher
File:07cpsca.ex
Update:Tue Aug 29 17:38:34 1995

186gearshift lever, may flash steadily if a
malfunction has been detected. If the Overdrive
Off Indicator Light is flashing, contact your Ford
dealer as soon as possible. If this condition
persists, damage to the transmission could occur.
*
[DR00700(ALL)03/95]
Some vehicles are equipped with a Powertrain
Control Module that limits engine speeds with a
cut-out mode to promote durability.
[DR05700(ALL)06/95]Automatic Overdrive
Transmission
%*
[DR05750(ALL)01/95]
Putting Your Vehicle in Gear
[DR05800(ALL)03/93]
Your vehicle's gearshift is on the steering
column. You can put the gearshift in any one of
several positions.
[DR06001(ALL)06/95]
one third page art:0095027-A
The positions of the column-mounted gearshift
*
[DR06200(ALL)05/95]
RWARNING
Hold the brake pedal down while you
move the gearshift lever from position to
position. If you do not hold the brake
pedal down, your vehicle may move
unexpectedly and injure someone.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995

188 %
*
[DR06401(ALL)01/95]
R (Reverse)
*
[DR06501(ALL)02/95]
With the gearshift in the R (Reverse) position,
the vehicle will move backward. You should
always come to a complete stop before shifting
into or out of R (Reverse).
*
[DR06520(ALL)01/95]
N (Neutral)
[DR06550(ALL)08/95]
In N (Neutral), the wheels of the vehicle are not
locked. Your vehicle will roll freely, even on the
slightest incline, unless the parking brake or
brakes are on.
%*
[DR06601(ALL)01/95]
Driving
%*
[DR06700(ALL)04/95]
When to usej(Overdrive)
[DR06800(ALL)08/95]
This is the normal driving position. As the
vehicle picks up speed, automatic upshifts to
second, third and fourth gears will occur when
jOverdrive is chosen on the selector and the
transmission control switch has not been
pressed. The transmission will shift into the
correct gear when the right speed is achieved,
for the accelerator pedal position you have
chosen.
[DR06810(ALL)08/95]
When to use Drive
[DR06830(ALL)08/95]
You will note there is not a drive position on
your gearshift indicator. However, you will find
a transmission control switch labeled
OVERDRIVE OFF located on the end of the
gearshift lever. Press this switch and the
indicator light (OFF) illuminates on the gearshift
lever. With overdrive cancelled and the word
OFF illuminated, the transmission will operate in
gears one through three. This is useful if you
experience frequent downshift/upshift
conditions, when operating with a heavy load or
in hilly terrain, or if additional engine braking is
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995

194
*
[DR22100(ALL)11/89]
Hydraulic Power Brakes
*
[DR22200(ALL)08/94]
The hydraulic brake system is made up of two
independent hydraulic circuits. One hydraulic
circuit supplies fluid to the front disc brakes and
the other hydraulic circuit supplies fluid to the
rear drum brakes. These two circuits are
supplied by a common hydraulic brake fluid
reservoir, with a fluid level sensor.
*
[DR22300(ALL)11/89]
The brake light in the instrument cluster will
light for low brake fluid in the common brake
fluid reservoir.
*
[DR22400(ALL)05/95]
RWARNING
An increase in pedal travel will result in
reduced braking capability. The brake
system should be checked immediately.
%*
[DR22500(ALL)10/94]
Rear Anti-lock Brakes
[DR22700(ALL)06/95]
Your vehicle is equipped with a rear Anti-lock
Brake System (ABS). This system prevents at
least one and often both rear wheels from
completely locking up when the brakes are
applied in a panic stop, for example.
*
[DR22800(ALL)07/94]
Even with the Anti-lock Brake System, you
should be careful when braking. Front brake
lock up on any surface, even on smooth
pavement causes loss of steering control. Heavy
braking on roads with loose surfaces such as
snow or gravel, or severe pavement irregularities
could also cause you to lose steering control of
your vehicle.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995

195
*
[DR22900(ALL)05/95]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[DR22910(ALL)07/95]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
%*
[DR23000(ALL)12/89]
If Brakes Do Not Grip Well or Pedal is
ªLowº
%*
[DR23200(ALL)07/95]
If brakes do not grip well, it may indicate the
rear drum brakes need adjustment. To do this,
drive the vehicle in reverse at 5 mph (8 km/h)
on level, dry pavement. Stop the vehicle by
firmly applying the brakes. Repeat this
procedure four or five times.
*
[DR23250(ALL)11/89]
If during normal operation the brake pedal
seems ªlowº, it may indicate the need for a
brake system inspection and/or service. You
should have your brakes checked as soon as
possible.
%*
[DR23300(ALL)07/95]
Occasional brake squeal during light to moderate
stops does not affect the function of the brake
system and is normal. However, if the squeal
becomes louder or more frequent, have your
brakes inspected by your dealer or a qualified
service technician.
File:10cpdra.ex
Update:Tue Aug 29 17:45:28 1995