ignition FORD AEROSTAR 1996 1.G Owners Manual
[x] Cancel search | Manufacturer: FORD, Model Year: 1996, Model line: AEROSTAR, Model: FORD AEROSTAR 1996 1.GPages: 353, PDF Size: 2.87 MB
Page 33 of 353
31
*
[SR12070(ALL)07/95]
To ensure that the air bag system will operate as
intended in a crash, the system is equipped with
a diagnostic module, which controls a readiness
lamp and a warning tone. The diagnostic
module monitors its own circuits, the air bag
electrical system, the air bag readiness light, the
air bag power, and the air bag inflators.
%*
[SR12200(ALL)05/95]
The air bag system uses a readiness light on the
instrument cluster and a tone to indicate the
condition of the system. When you turn the
ignition key to the ON position, this light will
illuminate for approximately six (6) seconds and
then turn off. This indicates that the system is
operating normally. NOTE: Maintenance of the
air bag system is not required.
%*
[SR12300(ALL)06/95]
A problem with the system is indicated by one
or more of the following:
*
[SR12310(ALL)06/95]
q
the readiness light will either flash or stay lit,
*
[SR12320(ALL)06/95]
q
or it will not light immediately after ignition
is turned on,
*
[SR12330(ALL)06/95]
q
or a group of five beeps will be heard. The
tone pattern will repeat periodically until the
problem and light are repaired.
*
[SR12360(ALL)08/95]
If any of these things happen, have the air bag
system serviced at your Ford or Lincoln-Mercury
dealer immediately. Unless serviced, the air bag
Supplemental Restraint System may not function
properly in the event of a collision.
*
[SR12600(ALL)07/95]
RWARNING
Do not attempt to service, repair, or
modify the Air Bag Supplemental
Restraint System or its fuses. See your
Ford or Lincoln-Mercury dealer.
File:03cpsra.ex
Update:Tue Aug 29 17:35:04 1995
Page 62 of 353
61
Starting Your Aerostar
*
[ST01700(ALL)03/95]
Ignition
%*
[ST01800(ALL)01/95]
Understanding the Positions of the Ignition
*
[ST02000(ALL)05/90]
quarter page art:0020004-B
The positions of the key in the ignition lock cylinder.
%*
[ST02100(ALL)07/95]
ACCESSORY allows some of your vehicle's
electrical accessories such as the radio and the
windshield wipers to operate while the engine is
not running.
*
[ST02500(ALL)08/95]
LOCK locks the steering wheel and gearshift
lever.
*
[ST02700(ALL)01/95]
LOCK is the only position that allows you to
remove the key. The LOCK feature helps to
protect your vehicle from theft.
*
[ST02800(ALL)05/95]
If your key is stuck in the LOCK position and
will not turn, move your steering wheel left or
right until the key turns freely.
*
[ST02850(ALL)03/95]
OFF allows you to shut off the engine and all
accessories without locking the steering wheel or
the automatic transmission gearshift lever.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 63 of 353
62
*
[ST02900(ALL)05/95]
ON allows you to test your vehicle's warning
lights (except the brake system warning light) to
make sure they work before you start the
engine. The key returns to the ON position once
the engine is started and remains in this position
while the engine runs.
*
[ST02950(ALL)03/95]
START cranks the engine. Release the key once
the engine starts so that you do not damage the
starter. The key should return to ON when you
release it. The START position also allows you
to test the brake warning light.
%*
[ST03000(ALL)02/95]
Removing the Key From the Ignition
*
[ST03400(ALL)06/95]
1. Put the gearshift in P (Park).
*
[ST03500(ALL)03/91]
2. Set the parking brake fully before removing
your foot from the service brake. (This will
avoid ªbindingº or ªloadingº the park gear
if you park on a grade.)
*
[ST03600(ALL)03/95]
3. Turn the ignition key to LOCK.
*
[ST03700(ALL)03/95]
4. Remove the key.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 64 of 353
63
*
[ST04625(ALL)06/95]
RWARNING
Always set the parking brake fully and
make sure the gearshift is securely latched
in P (Park).
*
[ST04750(ALL)01/93]
RWARNING
Do not leave children, unreliable adults,
or pets alone in your vehicle. They could
accidentally injure themselves or others
through inadvertent operation of the
vehicle. Further, on hot, sunny days,
temperatures in a closed vehicle could
quickly become high enough to cause
severe and possibly fatal injuries to
people as well as animals.
%*
[ST04775(ALL)03/91]
Ignition Key Buzzer or Chime
*
[ST04780(ALL)03/91]
The buzzer or chime will sound if you open the
driver's door while the key is in the ignition.
Never leave your vehicle unattended with the
key in the ignition.
%
*
[ST04800(ALL)03/95]
Fuel-Injected Engines
*
[ST04900(ALL)03/95]
When starting a fuel-injected engine,the most
important thing to remember is to avoid
pressing down on the accelerator before or
during starting. Only use the accelerator when
you have problems getting your vehicle started.
SeeStarting Your Enginein this chapter for
details about when to use the accelerator while
you start your vehicle.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 65 of 353
64
*
[ST05150(ALL)03/95]
Starting Your Vehicle
%*
[ST05200(ALL)05/94]
Preparing to Start Your Vehicle
*
[ST05300(ALL)07/95]
RWARNING
Do not start your vehicle in a closed
garage or other enclosed area. Never sit in
a stopped vehicle for more than a short
period of time with the engine running.
Exhaust fumes are toxic. SeeGuarding
Against Exhaust Fumesin this chapter for
more instructions.
*
[ST05400(ALL)01/95]
Before you start your vehicle, do the following:
*
[ST05500(ALL)08/95]
1. Make sure all occupants in the vehicle
buckle their safety belts. SeeSafety Restraints
in the Index for more details.
*
[ST05600(ALL)03/95]
2. Make sure the headlamps and other
accessories are turned off when starting.
*
[ST05750(ALL)03/95]
3. Make sure that the gearshift is in P (Park)
and the parking brake is set before you turn
the key.
*
[ST06015(ALL)03/95]
Before you start your vehicle, you should test
the warning lights on the instrument panel to
make sure that they work. Refer to theWarning
Lights and Gaugeschapter.
%*
[ST06200(ALL)02/95]
Starting Your Engine
*
[ST06300(ALL)06/95]
To start your engine:
*
[ST06400(ALL)05/95]
1. Follow the steps underPreparing to Start
Your Vehicleat the beginning of this section.
*
[ST06425(ALL)03/95]
2. Turn the ignition key to the ON position.
*
[ST06451(ALL)06/95]
3. DO NOT depress the accelerator pedal when
starting your engine. DO NOT use the
accelerator while the vehicle is parked.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 67 of 353
66 %
*
[ST06625(ALL)01/95]
NOTE: Your vehicle is equipped with a
brake-shift interlock feature. This
feature prevents you from shifting
from P (Park) unless you have the
brake pedal depressed. (The ignition
must be in the ON position.) If you
cannot shift from P (Park) with the
brake pedal depressed:
*
[ST06627(ALL)01/95]
1. Apply the parking brake.
*
[ST06629(ALL)01/95]
2. Remove the key.
*
[ST06631(ALL)08/95]
3. Insert the key and rotate it one position
clockwise (ignition in the OFF position).
*
[ST06633(ALL)08/95]
4. Apply the brake pedal and shift to N
(Neutral). (If the vehicle is shifted back to P
[Park], you must repeat the previous steps.)
*
[ST06635(ALL)01/95]
5. Start the vehicle.
*
[ST06637(ALL)07/95]
If you need to shift out of P (Park) by using the
alternate procedure described above, it is
possible that a fuse has blown and that your
brakelamps may also not be functional. Please
refer to the chapter titledServicing Your Aerostar
in this Owner Guide for instructions on checking
and replacing fuses.
*
[ST06640(ALL)05/95]
RWARNING
DO NOT DRIVE YOUR VEHICLE UNTIL
YOU VERIFY THAT THE BRAKELAMPS
ARE WORKING.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 68 of 353
67
*
[ST06800(ALL)06/95]
If the engine still does not start after two
attempts:
*
[ST06825(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST06851(ALL)04/95]
2. Press the accelerator all the way to the floor
and hold it.
*
[ST06876(ALL)04/95]
3. Turn the ignition key to the START position.
*
[ST06900(ALL)04/95]
4. Release the ignition key when the engine
starts.
*
[ST06925(ALL)04/95]
5. Release the accelerator gradually as the
engine speeds up. Then drive away in the
normal manner.
*
[ST06951(ALL)04/95]
If the engine still does not start, the fuel pump
shut-off switch may have been triggered. For
directions on how to reset the switch seeFuel
Pump Shut-Off Switchlater in this chapter.
%*
[ST07300(ALL)05/95]
A computer system controls the engine's idle
speed. When you start your vehicle, the engine's
idle speed normally runs high. These faster
engine speeds will make your vehicle move
slightly faster than its normal idle speed. It
should, however, slow down after a short time.
If it does not, have the idle speed checked.
*
[ST07390(ALL)07/95]
If the engine idle speed does not slow down
automatically, do not allow your vehicle to idle
for more than 10 minutes. Have the vehicle
checked.
*
[ST07400(ALL)05/95]
RWARNING
Extended idling at high engine speeds can
produce very high temperatures in the
engine and exhaust system, creating the
risk of fire or other damage.
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 71 of 353
70
*
[ST08250(ALL)03/95]
If your engine cranks but does not start after a
collision or substantial jolt:
*
[ST08275(ALL)04/95]
1. Turn the ignition key to the OFF position.
*
[ST08300(ALL)03/95]
2. Check under the vehicle for leaking fuel.
*
[ST08325(ALL)03/95]
3. If you do not see or smell fuel, push the red
reset button down. If the button is already
set, you may have a different mechanical
problem.
*
[ST08350(ALL)03/95]
4. Turn the ignition key to the ON position for
a few seconds, then turn it to the OFF
position.
*
[ST08375(ALL)03/95]
5. Check under the vehicle again for leaking
fuel.If you see or smell fuel, do not start
your vehicle again.If you do not see or
smell fuel, you can try to start your vehicle
again.
*
[ST08400(ALL)03/95]
6. Check all vehicle warning lights before
driving the vehicle.
*
[ST08425(ALL)03/95]
quarter page art:0020107-A
Reset button for fuel pump shut-off switch
File:04cpsta.ex
Update:Tue Aug 29 17:35:31 1995
Page 76 of 353
75
%*
[LG03000(ALL)06/94]
The Mechanical Cluster
*
[LG03100(ALL)06/93]
The following warning lights and gauges are on
the mechanical cluster. All of the warning lights
and gauges alert you to possible problems with
your vehicle. Some of the lights listed are
optional. The following sections detail what each
of these indicators means.
%*
[LG03200(ALL)06/95]
Brake System Warning Light
*
[LG03300(ALL)03/95]
The warning light for the brakes can show two
things Ð that the parking brake is not fully
released, or that the brake fluid level is low in
the master cylinder reservoir. If the fluid level is
low, the brake system should be checked by
your dealer or a qualified service technician.
*
[LG03400(ALL)05/94]
This light comes on when you turn the ignition
key to START to verify that the indicator bulb is
working. If the light stays on or comes on after
you have released the parking brake fully, have
the hydraulic brake system serviced.
*
[LG03500(ALL)05/95]
RWARNING
The BRAKE light indicates that the brakes
may not be working properly. Have the
brakes checked immediately.
[LG03600(ALL)07/95]
one inch art:0095034-A
Brake warning light symbol
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995
Page 77 of 353
76 [LG03700(ALL)07/95]Rear Anti-Lock (ABS) Brake Warning Light
[LG03900(ALL)05/95]
To check the rear ABS brake warning light turn
the ignition key to the ON position. The rear
ABS brake warning light should glow
momentarily.
*
[LG03950(ALL)06/94]
NOTE: If it does not glow momentarily, have
your vehicle's electrical system checked
immediately.
[LG03975(ALL)07/95]
NOTE: If the rear ABS brake warning light
begins to flash in a repeating flash
sequence, check the rear anti-lock
brake system continuous power fuse
and brake lights for proper operation.
[LG04000(ALL)05/95]
one inch art:0095035-A
Rear anti-lock warning light symbol
*
[LG04100(ALL)05/95]
RWARNING
If the anti-lock brake system warning
light remains on or comes on while
driving, have the braking system checked
by a qualified service technician as soon
as possible.
*
[LG04110(ALL)07/95]
NOTE: If a fault occurs in the anti-lock
system, and the brake warning light is
not lit, the anti-lock system is disabled
but normal brake function remains
operational.
File:05cplga.ex
Update:Tue Aug 29 17:36:50 1995