wheel FORD MUSTANG 1969 Volume One Chassis

03-02-18
Suspension

03-02-18

5.
Remove the cotter pin from the

upper ball joint stud nut.

6. Loosen the upper ball joint stud

nut one or two turns. Do not remove

the nut from the stud at this time.

7.
Install tool T57P-3006-A be-

tween the upper and lower ball joint

studs with the adapter screw on top

(Fig. 13). The tool should be seated

firmly against the ends of both studs

and not against the nuts or lower stud

cotter pin.

8. With a wrench, turn the adapter

screw until the tool places the stua

under tension. Tap the spindle near

the upper stud with a hammer to loos-

en the stud in the spindle. Do not

loosen the stud from the spindle with

tool pressure only.

9. Remove the tool from between

the ball joint studs and place a floor

jack under the lower arm.

10.
Raise the floor jack to relieve

the pressure from the upper ball joint

stud nut and remove the nut.

11.
Remove the upper arm inner

shaft attaching bolts. Remove the

upper arm and inner shaft as an as-

sembly (Fig. 1).

12.
Remove the bumpei from the

upper arm.

Installation

1.
Position the bumper to the upper

arm and install the nut and washer.

Torque the nut to specifications.

2.
Position the upper arm inner

shaft to the frame side rail and install

the 2 attaching bolts and washers

snug.

3.
Connect the upper ball joint stud

to the spindle and install the attaching

nut. Torque the nut to specification

and continue to tighten the nut until

the cotter pin hole in the stud is in

line with the nut slots. Then, install

the cotter pin.

4.
If equipped with drum type bra-

kes—Adjust the brakes as outlined in

Part 2-2. Install the wheel, tire, and

drum to the spindle and adjust the

wheel bearings as outlined in Part

3-12.

5.
If equipped with disc brak-

es—Install the wheel and tire on the

hub and adjust the wheel bearings as

outlined in Part 3-12.

6. Install the hub cap or wheel

cover.

7.
Remove the safety stands and

lower the front of the vehicle.

8. Check caster, camber, and toe-in

and adjust as required (Section 2, Part

3-D.
COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1.
Raise the front of the vehicle,

position safety stands under the

frame, and lower the vehicle slightly.

2.
Remove the wheel and tire.

3.
Remove the shock absorber

lower attaching nuts and washers.

4.
Remove the shock absorber

upper mounting bracket attaching

nuts,
and remove the shock absorber

and bracket as an assembly (Fig. 26).

On all 8-cylinder vehicles, remove

the air cleaner to obtain access for

tool installation.

5.
Install the spring compressor

tool and compress the spring (Figs.

19,
20 and 21).

6. Position a safety stand under the

lower arm.

7.
Remove the cotter pin from the

nut on the upper ball joint stud, and

loosen the nut one or two turns. Do

not remove the nut from the stud at

this time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs as shown in Fig. 10. The

tool should seat firmly against the

ends of both studs and not against the

stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension; then, hit the spindle

smartly near the upper stud with a

hammer to break the stud loose in the

spindle. Do not loosen the stud in the

spindle with tool pressure only. If

both arms are being removed, loosen

the lower stud in the same manner as

the upper stud.

10.
Remove the nut from the upper

stud and lift the stud out of the

spindle.

11.
Remove the upper arm inner

shaft attaching nuts from the engine

compartment, and remove the upper

arm.

12.
Wipe off all loose dirt from the

upper arm parts. Do not wash the ball

joint with a solvent.

Installation

1.
Position the upper arm on the

underbody mounting bracket, and in-

stall the nuts and lock washers on the

two inner shaft attaching bolts. The

specified keystone-type lock washers

must be used. Torque the nuts to

soecification.
2.
Position the upper ball joint stud

in the top of the wheel spindle, and in-

stall the stud nut. Torque the nut to

specification, and continue to tighten

it until the cotter pin hole and slots

line up. Install a new cotter pin.

3.
Release the coil spring, remove

the tool, and install the front shock

absorber and the wheel and tire.

LINCOLN CONTINENTAL

Removal

1.
Place a jack under the outer end

of the suspension lower arm and raise

the arm. Refer to Fig. 22.

2.
Remove the wheel and tire.

3.
Remove the cotter pin from the

upper ball joint stud. Loosen the nut

one or two turns.

4.
Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the upper stud nut.

5.
Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the upper

stud to loosen it from the spindle. Do

not loosen the stud with tool pressure

alone. Remove the nut.

UPPER MOUNTING BRACKET

LOWER RETAINING BOLTS F 1490-A

FIG. 26—Removing or Installing

Front Shock Absorber—Typicalprocarmanuals.com

03-02-19

Suspension

03-02-19

6. Raise the upper arm to free the

ball joint stud from the spindle. Wire

the upper end of the spindle to the un-

derbody to prevent damage to the

brake hose.

7.
Mark the position of the upper

arm shaft on the underbody member

to facilitate making caster and camber

adjustments after installation of the

upper arm.

8. Remove the suspension upper

arm-to-underbody attaching bolts,

lock washers, and attaching nuts.

Then, remove the upper arm.

Installation

1.
Position the upper arm shaft on

the underbody member. Line up the

shaft with the marks made before re-

moval of the arm.

2.
Install the attaching bolts and

lock washers. FABRICATE A

TOOL, AS SHOWN IN Fig. 27, to

hold the nut in place while starting the

attaching bolt into the nut. Remove

the tool; then, tighten the attaching

bolts to specification.

3.
Guide the ball joint stud into the

spindle. Install the attaching nut and

torque it to specification. Continue

tightening the nut to line up the cotter

pin hole. Install a new cotter pin.

4.
Install the wheel and tire, and

torque the wheel lug nuts to specifica-

tion.

5.
With the front end weight of the

car on the wheels, torque the bolts at

the ends of the upper arm shaft to

specification if the bushings were re-

placed.

6. Check the front wheel alignment.

FRONT WHEEL SPINDLE

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

Removal

1.
Raise the vehicle until the front

wheel clears the floor, and place a

support under the frame.

2.
Remove the hub cap or wheel

cover.

3.
If equipped with drum type

brakes—remove the wheel and tire

and brake drum as an assembly (Part

3-12). Remove the brake backing

plate attaching bolts and remove the

backing plate from the spindle. Wire

the backing plate to the underbody to

prevent damage to the brake hose.
1/16" GAUGE
-*.

STEEL (REFERENCE)

—3/16'
3/8'

1/2" DIAMETER PLUG WELD

F 1501-A

FIG. 27 -Upper Arm Shaft Installing Tool

4.
If equipped with disc brakes—re-

move the wheel and tire from the hub.

Remove 2 bolts and washers retaining

the caliper and brake hose to the

spindle. Remove the caliper from the

rotor and wire it to the underbody to

prevent damage to the brake hose.

Then, remove the hub and rotor from

the spindle (Part 3-12). Remove 3

bolts attaching the splash shield to the

spindle and remove the splash shield.

5.
Remove the steering connecting

rod from the spindle arm with tool

OTC462.

6. Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

7.
Install the ball joint remover tool

between the upper and lower ball joint

studs (Fig. 7). The tool sho.uld seat

firmly against the ends of both studs

and not against the stud nuts.

8. Turn the tool nut with a wrench

until the tool places the studs under

tension, and, with a hammer, tap the

spindle near the stud to loosen them

in the spindle. Do not loosen the studs

in the spindle with tool pressure only.

9. Position a floor jack under the

lower control arm.

10.
Remove the ball joint stud nuts

and lower the lower arm enough to re-

move the spring and the spindle.
Installation

1.
Position the spindle to the lower

ball joint stud and install the attaching

nut. Torque the nut to specification.

Continue to tighten the nut until the

cotter pin hole is in line with the slots

in the nut. Then, install the cotter pin.

2.
Position the spring and raise the

lower arm and guide and upper ball

joint stud into the spindle hole and in-

stall the attaching nut. Torque the nut

to specification and install the cotter

pin as outlined in the preceeding step.

3.
Remove the floor jack from

under the lower arm.

4.
Attach the steering connecting

rod to the spindle and install the nut.

Torque the nut to specification. Con-

tinue to tighten the nut until the cotter

pin hole is in line with the slots in the

nut. Then, install the cotter pin.

5.
If equipped with drum type

brakes—Position the brake backing

plate to the spindle and install the at-

taching bolts. Torque the bolts to spe-

cification. Adjust the brakes as out-

lined in Part 2-2. Install the wheel,

tire,
and drum to the spindle and ad-

just the wheel bearings as outlined in

Part 3-12).

6. If equipped with disc brak-

es—Install the splash shield on the

spindle and torque the attaching bolts

to specification (Part 3-13). Install theprocarmanuals.com

03-02-20
Suspension

03-02-20

hub and rotor on the spindle. Position

the caliper over the rotor and install

the attaching bolts. Torque the bolts

to specification (Part 3-13). Install the

wheel and tire on the hub and adjust

the wheel bearings as outlined in Part

3-12 .

7.
Install the hub cap or wheel

cover. Then, remove the support stand

and lower the vehicle.

8. Check caster, camber, and toe-in

(Part 3-1) and adjust as necessary.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Drum Brakes

Removal

1.
Position a support between the

upper arm and frame as shown in

Figs.
8 and 9; then, raise the vehicle

and position safety stands.

2.
Remove the hub cap or wheel

cover.

3.
Remove the grease cap from the

hub;
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the wheel, hub, and drum

assembly off the wheel spindle.

5.
Remove the brake backing plate

from the spindle. Support the plate to

prevent damage to the brake hose.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool 3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Remove the stud nuts and re-

move the spindle from both studs.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25).
2.
Raise the lower suspension arm

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the upper stud nut and

then the lower stud nut to specifica-

tion. Continue to tighten both nuts

until the cotter pin holes and slots line

up.
Install new cotter pins.

4.
Connect the spindle connecting

rod end to the spindle arm.

5.
Install the brake backing plate

on the spindle, and torque the bolts to

specification.

6. Install the wntel and drum and

adjust the wheel bearing (Part 3-12).

7.
Remove the safety stands, and

lower the vehicle.

8. Remove the support from be-

tween the upper arm and frame.

9. Check and, if necessary, adjust

caster, camber, and toe-in.

Disc Brakes

Removal

1.
Remove the hub cap or wheel

cover, and remove the wheel and tire

from the hub.

2.
Remove two bolts attaching the

caliper to the spindle. Remove the cal-

iper from the rotor and wire it to the

underbody to prevent damage to the

brake hose.

3.
Remove the grease cap from the

hub,
then, remove the adjusting nut,

washer, and outer bearing cone and

roller assembly.

4.
Pull the hub and rotor assembly

off the wheel spindle.

5.
Remove the three caliper shield

attaching bolts and remove the shield.

6. Disconnect the spindle connect-

ing rod end from the spindle arm

using Tool-3290-C.

7.
Remove the cotter pins from

both ball joint stud nuts, and loosen

the nuts one or two turns. Do not re-

move the nuts from the studs at this

time.

8. Position the ball joint remover

tool between the upper and lower ball

joint studs (Fig. 10). The tool should

seat firmly against the ends of both

studs and not against the stud nuts.

9. Turn the tool with a wrench until

the tool places the studs under consid-

erable tension, and, with a hammer,

hit the spindle smartly near the studs

to break them loose in the spindle. Do

not loosen the studs in the spindle

with tool pressure alone.

10.
Position a floor jack under the

lower suspension arm.
11.
Remove the upper and lower

ball joint stud nuts; lower the jack

and remove the spindle.

Installation

1.
Position the spindle on the lower

ball joint stud and install the stud nut

(Fig. 25). Torque the nut to specifica-

tion and install the cotter pin.

2.
Raise the lower suspension arm,

and guide the upper ball joint stud

into the spindle. Install the stud nut.

3.
Torque the nut to specifications

and install the cotter pin. Then, re-

move the floor jack.

4.
Connect the spindle connecting

rod end to the spindle arm and install

the attaching nut. Torque the nut to

specification and install the cotter pin.

5.
Position the caliper splash shield

to the spindle and install the attaching

bolts and nuts. Torque the nuts and

bolts to specification.

6. Install the hub and rotor on the

spindle.

7.
Position the caliper to the rotor

and spindle and install the attaching

bolts.
Torque the bolts to specification

and install the safety wire.

8. Install the wheel and tire on the

hub and adjust the wheel bearing

(Part 3-12).

9. Install the hub cap or wheel

cover.

10.
Before driving the vehicle,

pump the brake pedal several times to

obtain normal brake lining-to-rotor

clearance and restore normal brake

pedal travel.

LINCOLN CONTINENTAL

Removal

1.
Raise the vehicle. Place a sup-

port under each side rail to the rear of

the lower arm in the lifting pad area.

2.
Remove the wheel and tire from

the hub.

3.
Remove 2 bolts and washers that

attach the caliper to the spindle. Re-

move the caliper from the rotor and

wire it to the underbody to prevent

damage to the brake hose.

4.
Remove the hub and rotor from

the spindle.

5.
Remove the splash shield and

gasket from the spindle.

6. Disconnect the spindle arm con-

necting rod from the spindle arm with

Tool 3290-C. See Fig. 23.

7.
Remove the cotter pins from

both ball joint stud nuts. Loosen the

nuts one to two turns.procarmanuals.com

03-02-21
Suspension

03-02-21

8. Place a box wrench over the

lower end of the ball joint remover

tool, and position the tool as in Fig.

13.
The tool should seat firmly against

the ends of both studs, and not

against the stud nuts.

9. Turn the wrench until both studs

are under tension, and then, tap the

spindle with a hammer near the studs

to loosen them from the spindle. Do

not loosen
the
studs with tool pressure

alone.

10.
Place a jack under the outer

end of the lower arm, and raise the

arm several inches. Remove both ball

stud nuts, and remove t^e spindle.

Installation

1.
Position the new spindle onto the

upper and lower ball joint studs, in-

stall the stud nuts and tighten the nuts

to specifications. Continue to tighten

both nuts until the cotter pin holes

line up with the slots, then install new

cotter pines.

2.
Connect the spindle connecting

rod to the spindle arm. Install the re-

taining nut and tighten the nut to

specification. Continue to tighten the

nut until the cotter pin hole lines up

with the slot, then install a new cotter

pin.

3.
Install the gasket and splash

shield on the spindle. Tighten the at-

taching bolts to specifications.

4.
Install the hub and rotor on the

spindle.

5.
Install the caliper to the spindle

and tighten the attaching bolts to spe-

cifications. Check for the correct flex-

ible hose routing (Part 2-2).

6. Install the wheel and tire and ad-

just the wheel bearings (Part 3-12).

7.
Lubricate the steering stop on

the lower arm and the mating flat on

the spindle with the specified lubri-

cant.

8. Remove the safety stands, lower

the car and check camber, caster and

toe-in.

FRONT SHOCK ABSORBER

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK III

1.
Remove the nut, washer, and

bushing from the shock absorber

upper end.

2.
Raise the vehicle on a hoist and

install safety stands.
3.
Remove 2 bolts attaching the

shock absorber to the lower arm and

remove the shock absorber.

4.
Place a washer and bushing on

the shock absorber top stud and posi-

tion the shock absorber inside the

front spring. Install the 2 lower at-

taching bolts and torque them to spe-

cifications.

5.
Remove the safety stands and

lower the vehicle.

6. Place a bushing and washer on

the shock absorber top stud and in-

stall the attaching nut. Torque it to

specification.

COUGAR, FAIRLANE,

FALCON, MONTEGO,

MUSTANG

Removal

1. Raise the hood and remove 3

shock absorber upper mounting

bracket-to-spring tower attaching

nuts.

2.
Raise the front of the vehicle and

place safety stands under the lower

arms.

3.
Remove 2 shock absorber lower

attaching nuts and washers.

4.
Lift the shock absorber and

upper bracket from the spring tower

(Fig. 26) and remove the bracket from

the shock absorber.

Installation

1. Install the upper mounting

bracket on the shock absorber and

torque to specification.

2.
Position the shock absorber and

upper mounting bracket in the spring

tower, making sure the shock absor-

ber lower studs are in the pivot plate

holes.

3.
Install the 2 washers and attach-

ing nuts on the shock absorber lower

studs and torque to specification.

4.
Install the 3 shock absorber

upper mounting bracket-to-spring

tower attaching nuts and torque to

specification. Then, remove the safety

stands and lower the vehicle.

LINCOLN CONTINENTAL

Removal

1.
Remove the stud nut at the

upper eye of the shock absorber. Re-

move the upper eye stud bracket to

crossmember attaching bolt and re-

move the stud bracket. Refer to Fig.

22.
2.
Remove the bolts which attach

the shock absorber to the suspension

lower arm. Lower, and remove the

shock absorber.

3.
Examine the shock absorber unit

and rubber bushings. Replace parts

that are defective, deteriorated, or

worn.

Installation

1. Fully extend the shock absorber

and position it inside the coil spring.

Connect the lower end of the shock

absorber to the suspension lower arm.

Torque the attaching nuts to specifica-

tion.

2.
Insert the upper bracket stud

through the bushing in the shock ab-

sorber upper eye. Install the stud

bracket to crossmember attaching

bolt. Do not tighten the bolt: at this

time.

3.
Install the upper eye bracket

stud nut. Torque the nut to specifica-

tion.

4.
Torque the stud bracket- to-

crossmember attaching bolt to specifi-

cation.
The
shock absorber upper
eye

stud
nut
must
be
tightened
to com-

press
the
rubber bushing before
the

stud bracket
is
bolted
to the

crossmember;
otherwise,
the
upper
at-

tachment could
be
loose
and
noisy.

REAR SHOCK ABSORBER

REPLACEMENT

FORD, MERCURY,

METEOR, THUNDERBIRD,

CONTINENTAL MARK 1(11

1.
Raise the vehicle on a hoist.

2.
Remove the shock absorber at-

taching nut, washer and insulator

from the upper stud at the upper side

of the spring upper seat. Compress the

shock absorber to clear the hole in the

spring seat, and remove the inner in-

sulator and washer from the upper at-

taching stud.

3.
Remove the self-locking attach-

ing nut, and disconnect the shock ab-

sorber lower stud from the mounting

bracket on the rear axle housing (Fig.

4).

4.
Expel all air by performing step

3 On Vehicle Tests in Part 3-1.

5.
Place the inner washer and insu-

lator on the upper attaching stud, and

position the shock absorber so that

the upper attaching stud enters the

hole in the spring upper seat. While

holding the shock absorber in this po-

sition, install the outer insulator andprocarmanuals.com

03-02-22
Suspension

03-02-22

washer and the nut on the upper stud

from the upper side of the spring

upper seat. Torque the nut to specifi-

cations.

6. Extend the shock absorber and

locate the lower stud in the hole in

mounting bracket on the rear axle

housing. Install a new self-locking at-

taching nut and torque to specifica-

tion.

MUSTANG AND COUGAR

Removal

1.
Disconnect the shock absorber

from the spring clip plate (Fig. 30).

2.
Remove the shock absorber ac-

cess cover from the luggage compart-

ment (Fig. 28).-(On convertible mod-

els,
remove the rear seat and seat

back to reach the access cover.)

SHOCK ABSORBER ACCESS COVER
SHOCK ABSORBER UPPER ATTACHING NUT

LUGGAGE COMPARTMENT

FLOOR PANEL

F 1489-A

FIG. 28—Rear Shock Absorber

Access Cover

3.
Remove the shock absorber

upper attaching nut.

4.
Compress the shock absorber

and remove it from the vehicle. Re-

move the bushings and washers from

the shock absorber studs.

Installation

1.
Place the bushing and inner

washer on the shock absorber stud.

2.
Connect the upper stud to the

mounting, and install the bushing,
ACCESS COVER

F 1488-A

FIG. 29—Rear Shock Absorber

Upper Mounting

outer washer, and new nut on the

stud. Torque the nut to specification,

and install the cover.

3.
Connect the lower stud to the

spring clip plate, and install the bush-

ing, outer washer, and new nut on the

stud. Be sure that spring clip plate is

free of burrs. Tighten the nut to speci-

fication.

MONTEGO, FALCON, AND

FAIRLANE (EXCEPT

CONVERTIBLE)

Removal

1.
Open the luggage compartment

door, and remove the spare wheel and

tire.

On the Ranchero, remove the at-

taching screws, and lift the forward

half of the floor panel from the body;

then, remove the access cover from

the opening in the floor pan over the

shock absorber.

On station wagons, remove the ac-

cess cover from the opening in the

seat riser over the shock absorber.

2.
Fold back the floor mat and re-

move the shock absorber access cover

from the floor pan. Remove the nut,

outer washer, and rubber bushing that

attach the shock absorber to the upper

mounting in the floor pan (Fig. 29).

3.
Raise the vehicle and remove the

attaching nut, outer washer and bush-

ing from the shock absorber at the

spring clip plate (Fig. 30). Compress

the shock absorber and remove it

from the vehicle.

4.
If the shock absorber is service-

able and requires new bushings, remove

the inner bushings and washers from

the shock absorber studs.

Installation

1.
Place the inner washer and bush-

ing on each shock absorber stud.
2.
Expand the shock absorber and

position it to the spring clip plate and

to the mounting in the floor pan.

3.
Connect the lower stud to the

spring clip plate, and install the bush-

ing, outer washer, and new nut on the

stud (Fig. 30). Be sure the spring clip

plate is free of burrs.

On the Ranchero, after tightening

the nut to specification, install the for-

ward half of the floor panel.

4.
From the luggage compartment,

install the bushing outer washer and

new attaching nut to the upper mount-

ing stud (Fig. 29). Torque to specifica-

tion. On a station wagon, replace the

floor bed panel (14 screws).

5.
Place the spare wheel and tire in

the luggage compartment, and secure

it in the storage position.

MONTEGO AND FAIRLANE

CONVERTIBLE

Removal

1.
Remove the rear seat cushion

and seat back.

2.
Partially raise the vehicle on a

hoist. With an assistant under the ve-

hicle holding the shock absorber, re-

move the nut from the top of the

shock absorber.

3.
Remove the lower shock absor-

ber attaching nut and remove the

shock absorber.

Installation

1.
Position the washers and bush-

ings on the shock absorber and posi-

tion the shock absorber to the lower

attachment. Install the bushing, outer

washer, and new attaching nut and

torque the nut to specification (Part

3-13).

2.
Lower the vehicle and install the

bushing, outer washer, and new at-

taching nut on the top of the shock

absorber. Torque the nut to specifica-

tion.

3.
Install the rear seat back and

seat cushion.

LINCOLN CONTINENTAL

Removal

1.
Lift the vehicle and place support

stands under the axle housing. Posi-

tion the vehicle with a hoist to relieve

tension on the shock absorbers.

2.
Remove the screws that attach

the shock absorber mounting plate to

the crossmember (Fig. 31).procarmanuals.com

03-02-28
Suspension

03-02-28

used, these components should
be re-

placed
on the
bench.

Do not wash the ball joint with sol-

vent.
The
solvent
may
attack parts

within the joint.

BUSHING AND INNER

SHAFT REPLACEMENT

LINCOLN CONTINENTAL

Always replace both upper
arm

bushings,
if
either bushing
is
worn
or

damaged. Install only
new
bushings

when replacing
the
inner shaft. Refer

to Section
3 for
the upper arm remov-

al procedure.

1.
Remove
the
bolts, lock washers,

and flat washers from the ends
of
the

upper arm shaft.

2.
Assemble
the
remover, tool

3044-LA,
to the
shaft
at the
front

bushing. Press
the
bushing
out of the

arm using
the
support cup, tool 6069-

H,
and the
remover tool 3044-AB3

(Fig. 40).

PRESS RAM

FIG.
40
—Removing Upper
Arm

Front Bushing

3.
Remove
the
shaft.

4.
Remove
the
upper
arm
rear

bushing using
the
support
cup,
tool

3069-H, and
the
remover, tool 3069-L

(Fig. 41).

5.
Both upper
arm
bushings
are

pressed into the arm from the outside

toward the inside
of
the arm. To facil-

itate installation, use silicone
or
liquid

oap
as a
lubricant.
See
Fig.
41 for
PRESS RAM

Tool-3069-H

F 1480-A

FIG. 41—Removing Upper
Arm

Rear Bushing

proper assembly
of the
shaft
and

bushings.

6. Press the upper arm rear bushing

into
the arm
using
the
support cup,

tool 3069-H,
and the
replacer, tool

3068 (Fig. 43). Press
the
bushing
in

until
the
shoulder stop
is
reached.

7.
Insert
the end of the
shaft into

the rear bushing. Press the front bush-

ing onto
the
shaft
and
into
the arm

using the replacer, tool 3068 (Fig. 44).

REAR BUSHING
FRONT BUSHING

F 1479-A

FIG. 42— Upper Arm, Shaft,
and

Bushing Assembly

PRESS RAM

Tool— 3068

JF 1478-A
Bottom the bushing flange against the

flange
in the
arm.

8. Install
the
flat washers, lock-

washers,
and
bolts
at
the ends
of
the

upper
arm
shaft.
Do not
tighten
the

bolts
at
this time. These must
be

tightened after
the
arm assembly
has

been installed, and when the front end

weight
of
the vehicle
is
on the wheels.

These bolts
are
made
of a
special

material. Use only the specified bolt
if

replacement
is
necessary.

PRESS
RAM

FIG. 43—Installing Upper
Arm

Rear Bushing
FIG. 44—Installing Upper
Arm

Front Bushing

REAR SPRING OVERHAUL-

SPRING REMOVED

LINCOLN CONTINENTAL

Front Hanger Assembly

If
the
front hanger
or
bushings
are

to
be
replaced, proceed
as
follows:

1.
Remove
the
nuts and lock wash-

ers from
the
spring front mounting

bolt (Fig.
6).

2.
Tap the
spring mounting stud

out
of the
bushing
and
hanger, then

separate
the
hanger from
the
spring.

3.
Remove
the
front bushing from

the spring with tool T64N-5781-A.

4.
Install
the
bushing
in the
spring

with tool T64N-5781-A.

5.
Assemble the front hanger
to
the

spring
eye and
install
the
spring

mounting stud through
the
hanger,

bushings,
and
spring eye
as
shown
in

Fig.
6.

6. Install the lock washers and nuts

on
the
mounting stud
and
tighten
the

outboard
nut to
specification. Tighten

the inboard
nut to
specification with

the vehicle
at
curb riding height.procarmanuals.com

03-04-02
Automatic Air Leveling System — Lincoln Continental

03-04-02

REMOVAL AND INSTALLATION

COMPRESSOR

REMOVAL

1.
Raise the front of the vehicle and

place jack stands under frame side

rails.

2.
Turn the front wheels all the way

to the right. Working from the und-

erside of the left front fender, remove
the three shield attaching screws (Fig.

2).

3.
Disconnect the one vacuum line,

clean air intake line and the two pres-

sure lines from the compressor.

4.
Remove the two compressor

mounting bracket attaching bolts. Re-

move the bracket and compressor as

an assembly.

5.
Remove the three compressor to

bracket attaching nuts. Separate the

compressor from the bracket.
INSTALLATION

1.
Assemble the compressor and in-

sulators to the mounting bracket. In-

stall and torque the three nuts to spec-

ification.

2.
Position the compressor mount-

ing bracket and compressor and se-

cure with the two attaching nuts. Tor-

que the nuts to specification.

3.
Connect the vacuum line (coded

with a red stripe), clean air intake line

BRACKET
AND
COMPRESSOR
MUST
BE

ASSEMBLED
TOGETHER
PRIOR
TO

INSTALLATION
IN
VEHICLE
BOLT MUST
BE IN
PLACE

PRIOR
TO
INSTALLATION

OF
SUPPORT
INTO
VEHICLE

FIG. 2—Compressor Installation

CROSSMEMBER

EXHAUST
VALVE PORT

OVER
TRAVEL
LEVER

REAR AXLE
HOUSING

F1400-A

3—Height Control Valve
F1420-A

and the two pressure lines (Fig. 2) to

the compressor.

4.
Install the shield and three at-

taching screws.

5.
Remove the jack stands and

lower the vehicle.

HEIGHT CONTROL VALVE

REMOVAL

1.
Exhaust all air from system.

2.
Raise the rear of the vehicle and

support it with jack stands.

3.
Disconnect the link from the

height control valve arm.

4.
Disconnect the air inlet and the

outlet line from the valve.

5.
Remove the two control valve

mounting bracket attaching bolts (Fig.

3) and remove the valve.

INSTALLATION

1.
Position the height control valve

and install the two attaching bolts.

Torque the bolts to specification.

2.
Connect the air inlet and theprocarmanuals.com

03-05-01
Steering Columns And Linkage

03-05-01

PART 3-5 Steering
Columns
and Linkage

COMPONENT INDEX

ADJUSTING SLEEVE (LINKAGE)

Removal and Installation

CENTER LINK (LINKAGE)

Removal and Installation

LOCKING LEVER (TILT-AWAY COLUMN)

Removal and Installation

PITMAN ARM (LINKAGE)

Removal and Installation

SPINDLE CONNECTING ROD ASSEMBLY

(Inner and Outer Ends)

Removal and Installation

STATIONARY STEERING COLUMNS

Description

STEERING COLUMN

Alignment

Removal and Installation

STEERING COLUMN SHIFT TUBE

Removal and Installation

STEERING COLUMN UPPER BEARING

Removal and Installation

STEERING IDLER ARM AND BRACKET

ASSEMBLY

Removal and Installation

STEERING WHEEL

Removal and Installation

Spoke Position Adjustment

TILT-AWAY STEERING COLUMN

Description

TILT STEERING COLUMN

Description

TILT WHEEL STEERING COLUMN

STEERING SHAFT

Removal and Installation

VACUUM MOTOR (TILT-AWAY COLUMN)

Removal and Installation

VACUUM RELEASE VALVE (TILT-AWAY

COLUMN)

Removal and Installation
MODEL APPLICATION
All
Models

05-19

05-20

05-20

05-01

05-14

05-02

05-20

05-02

05-02
Ford
N/A

05-19

N/A

05-08

N/A

05-01

05-16

N/A

N/A
Mercury
N/A

05-19

N/A

05-08

N/A

05-01

05-16

N/A

N/A
Meteor
N/A

05-19

N/A

05-08

N/A

05-01

05-16

N/A

N/A
Cougar
05-06

05-19

N/A

05-10

05-02

N/A

N/A

05-05

05-05
Fairlane
N/A

05-19

N/A

05-09

N/A

N/A

N/A

N/A

N/A
Falcon
N/A

05-19

N/A

05-09

N/A

N/A

N/A

N/A

N/A
Montego
N/A

05-19

N/A

05-09

N/A

N/A

N/A

N/A

N/A
Mustang
05-06

05-19

N/A

05-10

05-02

N/A

N/A

05-05

05-05
Lincoln-
Continental
N/A

05-19

05-06

05-11

N/A

05-01

05-16

N/A

N/A
Thunderbird
05-06

05-19

05-07

05-14

05-02

N/A

N/A

05-05

05-05
Continental-
Mark
III
N/A

05-19

05-06

05-11

N/A

05-01

05-16

N/A

N/A

A page number indicates that the item is for the vehicle listed at the head of the column.

N/A indicates that the item is not applicable to the vehicle listed.

1 DESCRIPTION

STATIONARY STEERING COLUMNS

The steering column is of the col-

lapsible type to lessen the possibility

of injury to the driver of the vehicle

should he become involved in an acci-
dent. The lower end of the steering

column tube at the bellows area will

collapse approximately six inches

upon a hard impact.

The shift tube and the steering shaft

are provided with plastic dowels and
will shear and allow them to collapse

in proportion to the outer tube upon

impact.

Once the steering column has been

collapsed, a complete new column

must be installed with new brackets
procarmanuals.com

03-05-02
Steering Columns
And
Linkage

03-05-02

which also will shear away during
im-

pact.

TILT STEERING COLUMNS

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column
must
be
installed.

The tilt column features nine driv-

ing positions (four
up and
four down

from
a
center position).
The
.column

also features
a
turn signal switch with

a lane-changer position turn indicating

position
and
emergency warning flash-

er control.

TILT-AWAY STEERING COLUMNS

The tilt-away steering column
fea-

tures nine driving positions (four
up

and four down from
a
center position)

and
a
tilt-away position that
is
auto-

matically accomplished
on
Mustang

and Cougar models when
the
ignition

key
is
turned
to the
OFF
position
and

the left door
is
opened.
On
Thunder-

bird models,
the
tilt-away occurs when
the shift lever
is
placed
in
PARK
and

the driverns door
is
opened.

The steering column
is of the col-

lapsible type
to
lessen
the
possibility

of injury
to the
driver
of the
vehicle

should
he
become involved
in an
acci-

dent.
The
lower
end of the
steering

column tube
at the
bellows area will

collapse approximately
six
inches

upon
a
hard impact.

The shift tube
and the
steering shaft

are provided with plastic dowels
and

will shear
and
allow them
to
collapse

in proportion
to the
outer tube upon

impact.

Once
the
steering column
has
been

collapsed,
a
complete
new
column

must
be
installed along with mounting

brackets which will also shear away

during impact.

IN-VEHICLE ADJUSTMENTS
AND
REPAIRS

STEERING WHEEL SPOKE

POSITION ADJUSTMENT

When
the
steering gear
is on the

high point,
the
front wheels should
be

in
the
straight-ahead position
and the

steering wheel spokes should
be in

their normal position with
the
Pitman

arm pointing directly forward.
If the

spokes
are not in
their normal posi-

tion, they
can be
adjusted without
dis-

turbing
the
toe-in adjustment (Part

3-1).

STEERING WHEEL

REPLACEMENT

1.
Disconnect
the
negative cable

from
the
battery.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

crash
pad
attaching screws. Lift
the

crash
pad
from
the
wheel.
(On
Conti-

nental Mark
III
models,
pry out the

crash
pad
insert
and
remove
the two

screws that secure
the
crash
pad. Re-

move
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
nut,

and then remove
the
steering wheel

with tool T67L-3600-A
(Fig. 1). Do

not
use a
knock-off type steering

wheel puller
or
strike
the end of the

steering shaft with
a
hammer. Striking

the puller
or
shaft will damage
the

bearing
or the
collapsible column.

4.
Transfer
all
serviceable parts
to

the
new
steering wheel.

5.
Position
the
steering wheel
on

the shaft
so
that
the
alignment mark
on
the hub of the
wheel
is
adjacent
to

the
one on the
shaft. Install
a new

locknut
and
torque
it to
specifications.

6. Install
the
horn ring
(if so

equipped)
and
crash
pad.

STEERING COLUMN UPPER

BEARING REPLACEMENT

STATIONARY COLUMNS

Removal

1. Disconnect
the
horn wire
and the

turn indicator wires
at the
connector.

2.
Working from
the
underside
of

the steering wheel spoke, remove
the

two crash
pad
attaching screws. Lift

the crash
pad
from
the
wheel.
(On

Continental Mark
III
models,
pry out

the crash
pad
insert
and
remove
the

two screws that secure
the
crash
pad.

Remove
the
crash
pad. On
models

equipped with steering wheel mounted

speed controls, refer
to
Group
16 for

7oo/-T67L-3600-A
removal instructions). Remove
the

horn ring
(if so
equipped)
by
turning

it counterclockwise.

3.
Remove
the
steering wheel
at-

taching
nut.
Remove
the
steering

wheel using tool T67L-3600-A
(Fig.

1).
Do not use a
knock-off type steer-

ing wheel puller
or
strike
the end of

the steering shaft with
a
hammer.

Striking
the
puller
or
shaft will
dam-

age
the
bearing
or the
collapsible
col-

umn.

4.
Remove
the
turn indicator lever.

5.
Remove
the
turn signal switch

attaching screws. Lift
the
switch over

the
end of the
steering shaft
and
place

it
to one
side.

6. Remove
the
snap ring from
the

top
of the
steering shaft.

7.
Loosen
the two
flange-to-steering

column tube attaching bolts
to
disen-

gage them from
the
tube.

8. Raise
the
flange upward while

BEARING
AND

INSULATOR

Spacer

G 1502 -B

FIG.
1—Removing
Steering Wheel
G 1497-A

FIG. 2—Installing Upper Bearingprocarmanuals.com

03-05-03
Steering Columns And Linkage

03-05-03

tapping the steering shaft lightly with

a plastic hammer to free the bearing

and flange from the shaft.

9. Remove the bearing and insula-

tor from the flange.

Installation

1.
Install flange bolts (square head)

in flange if they were removed. Turn

the nuts onto the bolts one complete

turn only.

2.
Position the flange onto the

steering column tube.

3.
Engage the two flange bolt heads

with the square holes in the column

tube,
then tighten the two attaching

nuts to specification.

4.
Position the bearing and insula-

tor on the shaft. Work it down onto

the shaft as far as possible, then place

a piece of 3/4 ID x 2 1/8 inch pipe

over the end of the shaft and install

the steering wheel attaching nut (Fig.

2).

5.
Tighten the nut until the bearing

is seated in the flange, then remove

the nut and pipe from the shaft.

6. Position the turn signal switch

on the flange and install the three at-

taching screws.

7.
Make certain that the wheels are

in the straight ahead position. Place

the steering wheel on the steering

shaft with the spokes in the horizontal
position. Install and torque the attach-

ing nut to specification.

8. Secure the crash pad to the

steering wheel with the two attaching

screws.

9. Connect the horn and turn signal

wires.

10.
Install the turn signal lever.

TILT WHEEL COLUMNS

Removal

1.
Disconnect the negative cable

from the battery.

2.
Remove the steering wheel with

tool T67L-3600-A (Fig. 1). Install the

spring, shipping spacer (3/4 x 1 1/8-

inch pipe) and a steering wheel attach-

ing nut on the shaft. Do not use a

knock-off type steering wheel puller or

strike the end of the steering shaft

with a hammer. Striking the puller or

shaft will damage the bearing or the

collapsible column.

3.
Remove the turn indicator lever

(Fig. 3).

4.
Remove the three screws that at-

tach the upper cover to the column

and remove the cover. It may be nec-

essary to rotate the cover approxi-

mately
1/4—1/2
inch to engage the

cover lip in the slot of turn signal

switch to permit clearance.
5.
Loosen the screw on the bottom

side and slide the lower cover down-

ward on the column (on Ford and

Mercury models, remove the shroud.)

6. Remove the screw that secures

the turn signal wire retaining clip to

the column and remove the clip.

7.
Remove the two screws that at-

tach the turn signal switch to the

steering column. Move the switch

wires upward enough to permit lifting

the switch over the end of the steering

shaft and lay the switch to one side.

Be careful not to lose the turn signal

lever pivot from the switch.

8. Compress the steering column

locking clamp with vise grip pliers

(Fig. 4) and move the steering shaft to

the full up position.

9. Hold the column position spring

rod with vise grip pliers to prevent flo-

tation then compress the spring and

remove the retainer. Remove the plas-

tic cover and spring.

10.
Install tool T67P-3D739-B as

shown in Fig. 4. Thread the bolt in-

ward finger tight until it bottoms, then

back it out one full turn. Make sure

that the handle is centered over the

pivot pin to prevent bolt breakage.

Hold the 3/8 inch bolt head station-

ary, then tighten the nut to extract the

pin. Repeat this operation on the op-

posite pin.

11.
Remove the nut, shipping spa-

UPPER

COVER

J

G 1498-B

FIG. 3—Typical Steering Column—Disassembledprocarmanuals.com