lights FORD RANGER 1996 2.G Owner's Manual

90
[SC05508(ALL)10/94]
7-1/2 pica art:0021255-A*
[SC05510(ALL)11/93]
OVERDRIVE OFF Lamp
[SC05512(ALL)03/95]
This lamp indicates the operating range of the transmission.
This lamp illuminates when the O/D ON/OFF button is
depressed. For additional information, refer to theWarning
Lights and Gaugeschapter.
[SC05514(ALL)07/95]
6 pica art:0021226-B%*
[SC05516(ALL)03/95]
Hazard Flasher
*
[SC05520(ALL)04/95]
The hazard flasher is used to alert other drivers to hazardous
situations.
*
[SC05527(ALL)10/94]
The flashers will flash and the high-mount brakelamp will stay
on steadily (not flash) with the brake pedal depressed.
*
[SC05530(ALL)08/95]
The flashers work whether your vehicle is running or not. The
flashers work for up to two hours when the battery is fully
charged and in good condition without draining the battery
excessively. If the flashers run for longer than two hours or if
the battery is not fully charged, the battery power can be
drained.
File:07unscr.ex
Update:Wed May 1 13:46:58 1996

104and the parking lamps will flash. If a door is open or ajar, the
horn will give two short chirps warning you that a door is
open.
%*
[FV16800(ALL)02/95]
Remote entry personal alarm
*
[FV16900(ALL)02/95]
If you wish to activate the remote entry system personal alarm,
press the PANIC button. This will honk the horn and flash the
lights for approximately 2 minutes 45 seconds. You can turn it
off by pressing the PANIC button again from the transmitter or
by turning the ignition to the ON or ACCESSORY position.
*
[FV17000(ALL)02/95]
When you use the remote entry UNLOCK or PANIC buttons,
the illuminated entry system turns on the vehicle's interior
lights for 25 seconds. You can turn these lights off with the
remote entry LOCK button or by turning the ignition to the ON
or ACCESSORY position.
[FV17100(ALL)03/95]
7-1/2 pica art:0021160-A%*
[FV17200(ALL)04/95]
Arming and Disarming the Alarm System with Remote
Entry
*
[FV17350(ALL)04/95]
Your Remote Entry System will automatically arm the factory
installed Anti-Theft System when the doors are locked, and
automatically disarm it when the doors are unlocked. The
remote will also reset the anti-theft alarm (when the driver's
door is unlocked or the PANIC button is pressed on a
programmed remote entry transmitter) if it was triggered.
File:08unfvr.ex
Update:Wed May 1 13:48:36 1996

106
[FV18001(ALL)04/94]
7-1/2 pica art:0021162-A
Replacing the batteries
%*
[FV18101(ALL)02/95]
Replacing lost transmitters
[FV18200(ALL)07/95]
In the event a transmitter is lost, you should take your vehicle's
transmitters to your dealer to have the remote entry system
deprogrammed for the lost transmitter. This is necessary to
prevent further unauthorized use of the lost transmitter.
*
[FV18301(ALL)02/95]
You can also purchase additional transmitters (up to 4
transmitters can be used) from your dealer. You will need to
take all your transmitters to the dealer so they can program
them to the remote entry system all at the same time.
%*
[FV18601(ALL)04/95]
Illuminated Entry System (If equipped)
*
[FV18701(ALL)10/95]
This system will provide illumination of the vehicle's interior
courtesy lamps when either outside front door handle is pulled
or when the remote entry system is used to unlock the door or
sound the personal alarm. The system will automatically turn
off after approximately 25 seconds or when the ignition is
turned to the RUN or ACC position.
*
[FV18801(ALL)09/95]
NOTE: The inside lights will not turn off if you have turned
them on with the dimmer thumbwheel or if any door
is open.
File:08unfvr.ex
Update:Wed May 1 13:48:36 1996

Features
107
%*
[FV18900(ALL)08/94]
Battery Saver
*
[FV19000(ALL)03/95]
When the ignition is turned off, the vehicle will turn off battery
voltage to all of these lights after 40 minutes: glove box, engine
compartment, overhead console, mirror, courtesy and
interior (including cargo) lamps.
*
[FV19102(R )03/95]
This will prevent draining of the battery if these lights have
been left on inadvertently or if a door is not completely closed.
Battery voltage to these lamps will be restored when the remote
entry transmitter is used, any door is opened, or the ignition
key is turned on again.
%*
[FV19104(ALL)09/95]
Anti-Theft Alarm System (If equipped)
*
[FV19106(ALL)05/95]
When armed, this system helps protect your vehicle against
break-ins or theft.
%*
[FV19109(ALL)05/95]
When an unauthorized entry occurs, the system triggers and
will:
[FV19113(R )08/94]
n
flash the parking lamps and theft indicator lamp
*
[FV19115(ALL)06/95]
n
honk the horn
*
[FV19118(ALL)05/95]
n
disable the starting circuit to prevent the vehicle from being
started
% [FV19121(ALL)02/95]
Arming the System
*
[FV19124(ALL)04/95]
The system is ready to arm any time the ignition switch is
turned OFF and the alarm is not triggered or sounding. Any of
the following events will prearm the anti-theft system:
[FV19130(ALL)04/95]
n
Pressing the remote entry transmitter LOCK button to lock
the doors (with the doors open or closed),
*
[FV19136(ALL)04/95]
n
Opening a door and pressing the power door lock button to
lock the doors.
File:08unfvr.ex
Update:Wed May 1 13:48:36 1996

Features
109
*
[FV19200(ALL)02/95]
When unlocking the vehicle with a key, turn the key all the
way to the end of its travel or the system may not disarm.
*
[FV19202(ALL)09/95]
NOTE: The flashing lights and honking horn will shut off
automatically within 2 minutes 45 seconds after the
system is triggered. It will trigger again if another
intrusion occurs. However, the starter circuit remains
disabled until the system is disarmed.
*
[FV19205(ALL)05/95]
The anti-theft system is designed to work with the factory
installed remote entry system. It may not work with other
remote entry systems.
%*
[FV19250(ALL)02/95]
Windows
*
[FV19300(ALL)08/95]
Operating the Windows Manually
*
[FV19400(ALL)08/95]
The door windows are opened and closed by turning the handle
crank.
[FV19600(ALL)04/94]
7-1/2 pica art:0021163-A
Manual window operation
[FV21200(R )03/95]
Sliding rear window (If equipped)
[FV21500(R )06/94]
The sliding rear window has only one sliding portion. Follow
the operating instructions shown in the following illustration.
File:08unfvr.ex
Update:Wed May 1 13:48:36 1996

Electronic Sound Systems
153
*
[AS36000(ALL)08/95]
When the radio waves are reflected off objects or structures, the
reflected signal cancels the normal signal, causing the antenna to
pick up noise and distortion. Cancellation effects are most
prominent in metropolitan areas, but also can become quite
severe in hilly terrain and depressed roadways.
*
[AS36100(ALL)08/95]
To minimize these conditions, a stereo/mono blend circuit has
been incorporated into this system. This feature automatically
switches a weak stereo signal to a clearer monaural signal,
which improves the quality of reception.
*
[AS36200(ALL)08/95]
Several sources of static are normal conditions on AM
frequencies. These can be caused by power lines, electric fences,
traffic lights and thunderstorms.
*
[AS36300(ALL)08/95]
Another reception phenomenon isStrong Signal Capture and
Overload. This can occur when listening to a weak station and
when passing another broadcast tower. The close station may
capture the more distant station, although the displayed
frequency does not change. While passing the tower, the station
may switch back and forth a few times before returning to the
original station.
*
[AS36400(ALL)08/95]
When several broadcast towers are present (common in
metropolitan areas) several stations may overload the receiver,
resulting in considerable station changing, mixing and
distortion.
*
[AS36500(ALL)08/95]
Automatic gain control circuitry for both AM and FM bands has
been incorporated into this system to reduce strong signal
capture and overload.
File:09unasr.ex
Update:Wed May 1 13:49:43 1996

Driving Your Ranger
169
[DR16370(R )07/94]
4WD system indicator lights
[DR16401(R )10/94]
A 4WD light and a 4WD LOW light are located in the
instrument cluster.
[DR16430(R )10/94]
n
2H position Ð Neither the 4WD or the 4WD LOW lights are
lit.
[DR16460(R )07/94]
n
4H position Ð Only the 4WD light is lit.
[DR16490(R )10/94]
n
N position Ð Neither the 4WD or 4WD LOW lights are lit.
[DR16520(R )10/94]
n
4L position Ð Both the 4WD and the 4WD LOW lights are
lit.
*
[DR17060(R )06/94]
To shift from 2H to 4H:
*
[DR17090(R )06/94]
Stop the vehicle and engage the manual locking hubs by
turning both hub lock selector knobs clockwise to the LOCK
position. Move the transfer case shift lever straight back to the
4H position. After both hubs have been turned to the LOCK
position, shifts between 2H and 4H (or 4H to 2H) may take
place at any speed.
[DR17120(R )06/94]
10-1/2 pica
art:0021182-A
Locking hub positions
[DR17150(R )09/95]
NOTE: Do not drive the vehicle in 4H or 4L with the manual
locking hubs in the FREE position.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

172
[DR17660(R )01/95]
Electric shift system indicator lights
[DR17720(R )03/95]
A 4WD indicator light and a 4WD LOW indicator light are
located in the instrument cluster. If either light flashes, take
your vehicle in for service.
[DR17750(ALL)01/95]
n
Two-Wheel Drive mode Ð Neither the 4WD nor the 4WD
LOW lights are lit.
[DR17780(R )07/94]
n
4WD High Ð Only the 4WD light is lit.
[DR17810(ALL)10/94]
n
4WD LOW mode Ð Both the 4WD and 4WD LOW lights
are lit.
[DR17840(R )07/94]
To shift from Two-Wheel Drive to 4WD High:
[DR17871(R )08/94]
To shift into 4WD High rotate the 4WD switch located on the
instrument panel to 4x4 High. This shift can be done at a stop
or at speeds up to 55 miles per hour (88 km/h). When the
vehicle is driven, the automatic locking hubs will engage. If the
vehicle is stopped while in 4WD and the vehicle direction is
reversed from the previous direction, the automatic locking hubs
will momentarily disengage and reengage. The automatic
locking hubs may click as they automatically engage in the new
direction.
[DR17936(R )04/95]
10-1/2 pica
art:0020628-D
Select drive rotary switch
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

174
[DR18201(R )06/94]
During axle break-in or operation in extremely cold
temperatures, the automatic locking hubs may not release
completely. It may be necessary to drive the vehicle for 10 to 15
minutes before repeating the release procedure.
[DR18240(R )08/94]
To shift from 4x4 HIGH or 2WD to 4x4 LOW:
[DR18295(R )01/95]
Stop the vehicle, depress the brake and place the automatic
transmission in N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 LOW. Both the 4WD and 4WD LOW
lights are now lit.
[DR18350(R )08/94]
To shift from 4x4 LOW to 4x4 HIGH or 2WD:
[DR18380(R )01/95]
Stop the vehicle, depress the brake and place the automatic
transmission into N (Neutral) or depress the clutch on vehicles
with a manual transmission. Rotate the 4WD switch on the
instrument panel to 4x4 HIGH or 2WD.
[DR18500(ALL)03/95]
It is not recommended to operate the vehicle in the 4WD modes
with a temporary spare. If 4WD operation is necessary, do not
operate at speeds above 10 mph or for distances above 50 miles.
Extended operation in 4WD with a temporary spare may result
in damage to drivetrain components.
%*
[DR19200(ALL)01/89]
Driving Off Road with 4-Wheel Drive
*
[DR19300(ALL)11/89]
Most vehicles with four-wheel drive are especially equipped for
driving on sand, snow, mud, or rough terrain and have
operating characteristics that are somewhat different from
conventional vehicles, both off and on the road. The driving tips
below will help you learn to use four-wheel drive.
[DR19500(R )08/94]
n
Do not use four-wheel drive on dry, hard-surfaced roads,
especially with a temporary spare tire in use.
*
[DR19600(ALL)11/89]
n
Special maintenance procedures are necessary after operating
with drive components in water.
File:10undrr.ex
Update:Wed May 1 13:52:06 1996

219
Roadside Emergencies
%*
[RE00400(ALL)03/95]
Jump-Starting Your Vehicle
*
[RE00500(ALL)08/95]
Your vehicle's battery may die if you leave the lights on or any
electrical equipment on after you turn the engine off. If this
happens, you may be able to jump-start your vehicle with a
booster battery.
*
[RE00600(ALL)02/95]
RWARNING
The gases around the battery can explode if exposed to
flames, sparks, or lit cigarettes. An explosion could result
in injury or vehicle damage.
*
[RE00700(ALL)02/95]
RWARNING
To protect yourself when charging a battery, always
shield your face and eyes. Make sure that you can
breathe fresh air.
%*
[RE00800(ALL)06/95]
RWARNING
Applying too much pressure on the ends when lifting a
battery could cause acid to spill. Lift the battery with a
carrier or with your hands on the opposite corners.
%*
[RE00900(ALL)07/95]
RWARNING
Batteries contain sulfuric acid which burns skin, eyes,
and clothing.
*
[RE00910(ALL)07/95]
If the acid touches someone's skin, eyes, or clothing,
immediately flush the area with water for at least 15 minutes. If
someone swallows the acid, have him or her drink lots of milk
or water first, then Milk of Magnesia, a beaten egg, or vegetable
oil. Call a doctor immediately.
File:12unrer.ex
Update:Wed May 1 13:53:18 1996