timing belt FORD SIERRA 1987 2.G CVH Engines Workshop Manual

1.6 litre engine
Note: Unless otherwise stated, the Specifications for the 1.6 litre CVH engine are as given for the 1.8 litre (R2A type) which follow.
General
Engine code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . L6B
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.960 mm
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.520 mm
Cubic capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1596 cc
Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9.0 :1
Compression pressure at starter motor speed . . . . . . . . . . . . . . . . . . . . 12.2 to 14.3 bars
Maximum continuous engine speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6000 rpm
Maximum engine power (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59 kW at 5500 rpm
Maximum engine torque (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121 Nm at 3500 rpm
Cylinder bore diameter
Standard class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.940 to 79.950 mm
Standard class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.950 to 79.960 mm
Standard class 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.960 to 79.970 mm
Standard class 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79.970 to 79.980 mm
Oversize class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80.230 to 80.240 mm
Oversize class B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80.240 to 80.250 mm
Oversize class C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80.250 to 80.260 mm
Chapter 2 Part C:
CVH engines
Camshaft and cam followers - removal, inspection and refitting . . . .23
Compression test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Crankcase ventilation system - inspection and maintenance . . . . . . .3
Crankshaft and bearings - examination and renovation . . . . . . . . . .33
Crankshaft and main bearings - removal and refitting . . . . . . . . . . . .32
Crankshaft front oil seal - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Crankshaft rear oil seal - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . .26
Cylinder block and bores - examination and renovation . . . . . . . . . .34
Cylinder head - dismantling and reassembly . . . . . . . . . . . . . . . . . . .21
Cylinder head - inspection and renovation . . . . . . . . . . . . . . . . . . . . .22
Cylinder head - removal and refitting (engine in vehicle) . . . . . . . . . .19
Cylinder head - removal and refitting (engine removed) . . . . . . . . . . .20
Engine - refitting (automatic transmission in vehicle) . . . . . . . . . . . . .13
Engine - refitting (manual gearbox in vehicle) . . . . . . . . . . . . . . . . . . .12
Engine - removal leaving automatic transmission in vehicle . . . . . . . .9
Engine - removal leaving manual gearbox in vehicle . . . . . . . . . . . . . .8
Engine/automatic transmission assembly - reconnection and
refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Engine/automatic transmission assembly - removal and separation .11Engine dismantling, examination, renovation and reassembly - general
information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Engine/manual gearbox assembly - reconnection and refitting . . . . .14
Engine/manual gearbox assembly - removal and separation . . . . . .10
Engine mountings - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Engine oil and filter - renewal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Flywheel/driveplate - removal, inspection and refitting . . . . . . . . . . .24
General information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Initial start-up after overhaul or major repair . . . . . . . . . . . . . . . . . . .35
Major operations possible with the engine in the vehicle . . . . . . . . . . .5
Major operations requiring engine removal . . . . . . . . . . . . . . . . . . . . .6
Method of engine removal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Oil pump - dismantling, inspection and reassembly . . . . . . . . . . . . .29
Oil pump - removal and refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
Pistons and connecting rods - examination and renovation . . . . . . .31
Pistons and connecting rods - removal and refitting . . . . . . . . . . . . .30
Sump - removal and refitting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Timing belt and sprockets - removal and refitting . . . . . . . . . . . . . . .18
2C•1
Specifications Contents
2C
Easy,suitable for
novice with little
experienceFairly easy,suitable
for beginner with
some experienceFairly difficult,
suitable for competent
DIY mechanic
Difficult,suitable for
experienced DIY
mechanicVery difficult,
suitable for expert
DIY or professional
Degrees of difficulty

Torque wrench settingsNmlbf ft
Main bearing cap bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 to 10066 to 74
Connecting rod (big-end bearing cap) bolts . . . . . . . . . . . . . . . . . . . . . .30 to 3622 to 27
Crankshaft pulley bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .100 to 11574 to 85
Camshaft sprocket bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54 to 5940 to 44
Flywheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 to 9261 to 68
Oil pump bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 116 to 8
Oil pump cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 126 to 9
Sump bolts (in two stages) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 to 84 to 6
Rocker arm nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 to 2918 to 21
Cylinder head bolts:
Stage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 to 4015 to 30
Stage 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 to 6030 to 44
Stage 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Angle-tighten a further 90º
Stage 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Angle-tighten a further 90º
Camshaft cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 to 84 to 6
Timing cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 to 117 to 8
Timing belt tensioner bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16 to 2012 to 15
Oil pick-up tube/strainer-to-oil pump bolts . . . . . . . . . . . . . . . . . . . . . .8 to 126 to 9
Oil pick-up tube/strainer-to-cylinder block bolt . . . . . . . . . . . . . . . . . . .17 to 2313 to 17
Camshaft thrustplate bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 to 137 to 10
Crankshaft rear oil seal housing bolts . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 116 to 8
1.8 litre (R2A type) engine
General
Engine type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Four-cylinder, in-line, single overhead camshaft
Firing order . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3-4-2
Engine code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .R2A
Bore . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80.00 mm
Stroke . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .88.00 mm
Cubic capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1769 cc
Compression ratio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9.3:1
Compression pressure at starter motor speed . . . . . . . . . . . . . . . . . . . .11 to 13 bar
Maximum continuous engine speed . . . . . . . . . . . . . . . . . . . . . . . . . . . .5850 rpm
Maximum engine power (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .66 kW at 5250 rpm
Maximum engine torque (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .147 Nm at 3000 rpm
Cylinder bore diameter
Standard class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.940 to 79.950 mm
Standard class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.950 to 79.960 mm
Standard class 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.960 to 79.970 mm
Standard class 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.970 to 79.980 mm
Standard class 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.980 to 79.990 mm
Standard class 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.990 to 80.000 mm
Oversize class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80.000 to 80.010 mm
Oversize class B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80.010 to 80.020 mm
Oversize class C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80.020 to 80.030 mm
Crankshaft
Endfloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.10 to 0.20 mm (0.004 to 0.008 in)
Main bearing running clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.028 to 0.067 mm
Main bearing journal diameter:
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53.980 to 54.000 mm
Undersize 0.25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53.730 to 54.750 mm
Undersize 0.50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53.480 to 53.500 mm
Undersize 0.75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53.230 to 53.250 mm
Centre main thrust bearing shell width:
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28.825 to 28.875 mm
Undersize 0.15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28.675 to 28.725 mm
Big-end bearing running clearance . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.020 to 0.065 mm
Big-end bearing journal diameter:
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43.890 to 43.910 mm
Undersize 0.25 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43.640 to 43.660 mm
Undersize 0.50 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43.390 to 43.410 mm
Undersize 0.75 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43.140 to 43.160 mm
Undersize 1.00 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42.890 to 42.910 mm
CVH engines 2C•3
2C

Pistons and piston rings
Piston diameter:
Standard class 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.910 to 79.920 mm
Standard class 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.920 to 79.930 mm
Standard class 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.930 to 79.940 mm
Standard class 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.940 to 79.950 mm
Standard class 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.950 to 79.960 mm
Standard class 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.960 to 79.970 mm
Oversize class A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.970 to 79.980 mm
Oversize class B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.980 to 79.990 mm
Oversize class C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79.990 to 80.000 mm
Camshaft
Endfloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.15 to 0.20 mm (0.006 to 0.008 in)
Thrustplate thickness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.99 to 5.01 mm (0.1966 to 0.1974 in)
Bearing journal diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45.7625 to 45.7375 mm
Valves
Valve timing:
Inlet opens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22º BTDC
Inlet closes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .54º ABDC
Exhaust opens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64º BBDC
Exhaust closes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12º ATDC
Valve spring free length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47.20 mm (1.86 in)
Inlet valve stem diameter:
Standard . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.025 to 8.043 mm
Oversize 0.38 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.405 to 8.423 mm
Oversize 0.76 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8.825 to 8.843 mm
Exhaust valve stem diameter (standard) . . . . . . . . . . . . . . . . . . . . . . . .7.996 to 8.017 mm
Lubrication system
Oil type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Multigrade engine oil, viscosity range SAE 10W/30 to 20W/50, to API
SG/CD or better
Oil capacity:
With filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4.0 litres (7.0 pints)
Without filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3.5 litres (6.2 pints)
Oil filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Champion C104
Oil pump clearances:
Outer rotor to body . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.074 to 0.161 mm (0.003 to 0.006 in)
Inner rotor to outer rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.050 to 0.180 mm (0.002 to 0.007 in)
Rotor endfloat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0.013 to 0.070 mm (0.0005 to 0.0028 in)
Torque wrench settingsNmlbf ft
Main bearing cap bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .90 to 10866 to 80
Big-end bearing caps:
With retaining nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .26 to 3419 to 25
With retaining bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35 to 4126 to 30
Crankshaft pulley bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110 to 13081 to 96
Camshaft sprocket bolt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95 to 11570 to 85
Flywheel bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .73 to 9154 to 67
Oil pump bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11 to 168 to 12
Oil pump cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 to 127 to 9
Sump bolts:
M6 bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 116 to 8
M8 bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 to 3015 to 22
Sump drain plug . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20 to 3015 to 22
Rocker arm bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 to 3017 to 22
Cylinder head bolts:
Stage 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 to 6030 to 44
Stage 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Slacken bolts by half a turn
Stage 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 to 6030 to 44
Stage 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten through a further 90º
Stage 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tighten through a further 90º
Camshaft cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 116 to 8
Timing cover bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 to 116 to 8
Timing cover nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 to 74 to 5
Timing belt tensioner bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23 to 3017 to 22
Oil pick-up tube/strainer-to-oil pump bolts . . . . . . . . . . . . . . . . . . . . . .10 to 137 to 9
Camshaft thrustplate bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 to 136 to 9
Crankshaft rear oil seal housing bolts . . . . . . . . . . . . . . . . . . . . . . . . . .20 to 3015 to 22
2C•4CVH engines

1.8 litre (R6A type) engine
Note: Unless otherwise stated, the Specifications for this later version of the 1.8 litre CVH engine are as given for the earlier R2A type above.
General
Engine code . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .R6A
Maximum continuous engine speed . . . . . . . . . . . . . . . . . . . . . . . . . . . .5700 rpm
Maximum engine power (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64 kW at 5200 rpm
Maximum engine torque (DIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .145 Nm at 3000 rpm
Valve timing
Inlet opens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24º BTDC
Inlet closes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .116º BTDC
Exhaust opens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .110º ATDC
Exhaust closes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18º ATDC
1.6 litre engine
The 1.6 litre CVH engine was introduced in
September 1991, to replace the 1.6 litre
SOHC engine used previously in the Sierra
range. The engine is broadly similar to the 1.8
litre (R2A type) CVH engine described below.
The main differences are outlined in the
following paragraphs.
The centre main bearing is fitted with
thrustwashers to control crankshaft endfloat,
instead of a flanged bearing shell.
The hydraulic cam followers operate in a
similar manner to those described for the 1.8
litre (R2A) engine but no rollers are fitted, and
the base of each cam follower is in direct
contact with the cam profile.
A distributorless ignition system is used and
a blanking plate is therefore fitted to the cylinder
head in place of the distributor drive. The
electric fuel pump is mounted in the fuel tank.
A comprehensive emissions control system
is fitted, comprising Central Fuel Injection
(CFI), a sophisticated engine management
system, a crankcase ventilation system, a
catalytic converter, and a pulseair system (to
reduce exhaust gas emissions).
Unless otherwise stated, all procedures are
as described for the 1.8 litre (R2A) engine.
1.8 litre (R2A type) engine
The CVH (Compound Valve angle,
Hemispherical combustion chambers) engine
is of four-cylinder, in-line, single overhead
camshaft type. The engine was introduced to
replace the 1.8 SOHC engine previously used
in the range.
The crankshaft incorporates five main
bearings. The centre main bearing has a
flanged bearing shell (thrust bearing) fitted to
the cylinder block to control crankshaft endfloat
The camshaft is driven by a toothed belt and
operates the compound angled valves via roller
type hydraulic cam followers, which eliminates
the need for valve clearance adjustment. The
cam followers operate in the following way.
When the valve is closed, pressurised engine
oil passes through ports in the body of the cam
follower and the plunger into the cylinder feed
chamber. From this chamber, oil flows through
a ball type non-return valve into the pressurechamber. The tension of the coil spring causes
the plunger to press the rocker arm against the
valve and to eliminate any free play.
As the cam lifts the cam follower, the oil
pressure in the pressure chamber increases
and causes the non-return valve to close the
port to the feed chamber. As oil cannot be
compressed, it forms a rigid link between the
body of the cam follower, the cylinder and the
plunger which then rise as one component to
open the valve.
The clearance between the body of the cam
follower and the cylinder is accurately designed
to meter a specific quantity of oil as it escapes
from the pressure chamber. Oil will only pass
along the cylinder bore when pressure is high
during the moment of valve opening. Once the
valve has closed, the escape of oil will produce
a small amount of free play and no pressure will
exist in the pressure chamber. Oil from the feed
chamber can then flow through the non-return
valve into the pressure chamber so that the
cam follower cylinder can be raised by the
pressure of the coil spring, thus eliminating any
play in the arrangement until the valve is
operated again.
As wear occurs between rocker arm and
valve stem, the quantity of oil which flows into
the pressure chamber will be slightly more
than the quantity lost during the expansion
cycle of the cam follower. Conversely, when
the cam follower is compressed by the
expansion of the valve, a slightly smaller
quantity of oil will flow into the pressure
chamber than was lost.
To reduce valve clatter when the engine is
started, a small plastic stand pipe retains oil
inside the plunger. When the engine is started,
the reservoir in the plunger (and via the non-
return valve, the pressure chamber) are
immediately filled with oil. This reduces the
noise often associated with hydraulic cam
followers as they pressurise with oil after
engine start-up.
The cam follower rollers run in needle
bearings, which greatly reduces friction as the
rollers follow the cam profile.
The distributor and fuel pump are driven
directly from the camshaft and the oil pump is
driven directly from the front of the crankshaft.
The cylinder head is of crossflow design,
with the inlet manifold mounted on the right-
hand side and the exhaust manifold mounted
on the left-hand side.
Lubrication is by means of a bi-rotor pumpwhich draws oil through a strainer located
inside the sump and forces it through a full-
flow filter into the oil galleries where it is
distributed to the crankshaft and camshaft.
The big-end bearings are supplied with oil via
internal drillings in the crankshaft. The
undersides of the pistons are supplied with oil
from drillings in the big-ends. The hydraulic
cam followers are supplied with oil from the
camshaft bearings via short passages in the
cylinder head.
A semi-closed crankcase ventilation system
is employed whereby piston blow-by gases
are drawn from the crankcase, through the
camshaft cover via an external vent hose, out
to an oil separator built into the base of the air
cleaner.
1.8 litre (R6A type) engine
The 1.8 litre (R6A type) CVH engine,
introduced in March 1992, is a further
development of the earlier 1.8 litre (R2A type)
unit described above. Apart from minor
engineering modifications to provide
increased fuel economy, reliability and power
output, the engine is mechanically identical to
the earlier version.
In common with the 1.6 litre unit, a
distributorless ignition system is used,
together with a comprehensive emissions
control system comprising Central Fuel
Injection (CFI), a sophisticated engine
management system, a crankcase ventilation
system, a catalytic converter, and additionally,
an exhaust gas recirculation (EGR) system.
Unless otherwise stated, all procedures are
as described for the 1.8 litre (R2A type)
engine.
Refer to Section 2, Chapter 2, Part A.
Refer to Chapter 1, Section 35.
Refer to Section 5, Chapter 2, Part A.
4Compression test
3Crankcase ventilation system -
inspection and maintenance
2Engine oil and filter - renewal
1General information
CVH engines 2C•5
2C

a)Removal of the cylinder head
b)Removal of the camshaft
c)Removal of the timing belt and sprockets
d)Removal of the engine mountings
e)Removal of the clutch and flywheel
f)Removal of the crankshaft oil seals
a)Removal of the sump
b)Removal of the oil pump
c)Removal of the pistons/connecting rods
d)Removal of the big-end bearings
e)Removal of the crankshaft main bearings
f)Removal of the crankshaft
Refer to Section 8, Chapter 2, Part A.
Note: A suitable hoist and lifting tackle will be
required for this operation.
1.8 litre (R2A type)
1Disconnect the battery negative lead.
2Remove the bonnet.
3Remove the air cleaner.
4Disconnect the cooling fan wiring plug, then
unscrew the retaining nuts and washers and
withdraw the fan shroud and cooling fan
assembly.
5Drain the cooling system.
6Disconnect the coolant hoses from the
coolant pump elbow, and detach the heater
hose from the clip on the front of the timing
cover.
7Disconnect the upper radiator hose and the
expansion tank hose from the thermostat
housing (see illustration).8Disconnect the heater hose from the
automatic choke.
9Disconnect the brake servo vacuum hose
from the inlet manifold (see illustration).
10Disconnect the throttle damper solenoid
vacuum pipes (noting their locations) from the
throttle damper and the carburettor “T”-piece
connector.
11Disconnect the engine management
module vacuum pipe from the inlet manifold.
12Disconnect the fuel hoses from the
carburettor and fuel pump, and plug the ends
of the hoses to minimise petrol spillage. Take
adequate fire precautions.
13Disconnect the throttle cable.
14Disconnect the HT leads from the coil and
spark plugs, unclip the leads from the
camshaft cover, and remove the distributor
cap, rotor arm and housing.
15Disconnect the wiring from the following
components:
Alternator
Starter motor
Oil pressure warning lamp switch
Temperature gauge sender
Engine coolant temperature sensor
Automatic choke
Cooling fan switch
Crankshaft speed/position sensor
Engine earth strap to battery tray16Unscrew and remove the top engine-to-
gearbox bolts which are accessible from the
engine compartment.
17Apply the handbrake (if not already done),
jack up the front of the vehicle and support on
axle stands (see “Jacking and Vehicle
Support”).
18Drain the engine oil into a container.
19Remove the starter motor.
20Remove the exhaust downpipe.
21Unscrew the two nuts securing the engine
mountings to the crossmember. Recover the
washers.
22Unscrew and remove the remaining
engine-to-gearbox bolts, noting the location
of the earth strap (see illustration), and
remove the two bolts from the engine adapter
plate (see illustration).
23Working inside the vehicle, place a
wooden block under the clutch pedal to raise
it fully against its stop which will hold the
automatic adjuster pawl clear of the toothed
quadrant.
24Disconnect the clutch cable from the
release arm, and pass the cable through the
bellhousing. Remove the clip securing the
clutch cable to the right-hand engine
mounting bracket. Note the cable routing for
use when refitting.
25Lower the vehicle to the ground, and
support the gearbox with a trolley jack using a
block of wood between the jack and the
gearbox to spread the load.
26Make a final check to ensure that all
relevant wires, pipes and hoses have been
disconnected to facilitate engine removal.
27Attach a suitable hoist to the engine lifting
brackets located at the front and rear of the
cylinder head, and carefully take the weight of
the engine. The engine should be supported
horizontally, ie do not allow it to tilt front to
rear.
28Raise the engine until the engine
mounting studs are clear of the crossmember,
then pull the engine forwards to disconnect it
from the gearbox. Ensure that the gearbox is
adequately supported, and take care not to
strain the gearbox input shaft. It may be
necessary to rock the engine a little to release
it from the gearbox.
8Engine - removal leaving
manual gearbox in vehicle
7Method of engine removal
6Major operations requiring
engine removal
5Major operations possible with
the engine in the vehicle
2C•6CVH engines
8.9 Disconnecting the brake servo vacuum
hose from the inlet manifold -
1.8 litre (R2A)
8.22b Remove the two bolts (arrowed) from
the engine adapter plate - 1.8 litre (R2A)8.22a Earth strap location under engine-to-
gearbox bolt - 1.8 litre (R2A)
8.7 Disconnect the upper radiator hose (1)
and the expansion tank hose (2) from the
thermostat housing - 1.8 litre (R2A)

1.8 litre (R2A type)
Dismantling
1It is best to mount the engine on a
dismantling stand, but if this is not available,
stand the engine on a strong bench at a
comfortable working height. Failing this, it will
have to stripped down on the floor.
2Cleanliness is most important, and if the
engine is dirty, it should be cleaned with
paraffin while keeping it in an upright position.
3Avoid working with the engine directly on a
concrete floor, as grit presents a real source
of trouble.
4As parts are removed, clean them in a
paraffin bath. However, do not immerse parts
with internal oilways in paraffin as it is difficult
to remove, usually requiring a high pressure
hose. Clean oilways with nylon pipe cleaners.
5It is advisable to have suitable containers
available to hold small items according to
their use, as this will help when reassembling
the engine and also prevent possible losses.
6Always obtain a complete set of new
gaskets for use during engine reassembly, but
retain the old gaskets with a view to using
them as a pattern to make a replacement if a
new one is not available.
7Where possible, refit securing nuts, bolts
and washers to their locations after removing
the relevant components. This will help to
protect the threads and will also prevent
possible losses.
8Retain unserviceable components in order
to compare them with the new components
supplied.
9A suitable Torx socket will be required to
remove the oil pump cover securing screws.
10Before dismantling the main engine
components, the following externally mounted
ancillary components can be removed:
Inlet manifold and carburettor
Exhaust manifold
Fuel pump and operating pushrod
Alternator
Spark plugs
Oil pressure warning lamp switch (see
illustration)
Oil filter
Dipstick
Engine mounting brackets
Clutch
Alternator mounting bracket
Crankshaft speed/position sensor
Engine lifting brackets
Examination and renovation
11Refer to Section 18 in Chapter 2, PartA.
Reassembly
12To ensure maximum life with minimum
trouble from a rebuilt engine, not only must
everything be correctly assembled, but it mustalso be spotlessly clean. All oilways must be
clear, and locking washers and spring
washers must be fitted where indicated. Oil all
bearings and other working surfaces
thoroughly with engine oil during assembly.
13Before assembly begins, renew any bolts
or studs with damaged threads.
14Gather together a torque wrench, oil can,
clean rag, and a set of engine gaskets and oil
seals, together with a new oil filter.
15If they have been removed, new cylinder
head bolts, big-end bolts/nuts and new
flywheel bolts will be required.
16After reassembling the main engine
components, refer to paragraph 10 and refit
the ancillary components listed. Delicate
items such as the alternator may be left until
after the engine has been refitted.
1.6 and 1.8 litre (R6A type)
Dismantling
17Refer to paragraphs 1 to 9 inclusive.
18Before dismantling the main engine
components, the following ancillary
components can be removed:
Inlet manifold and CFI unit.
Exhaust manifold .
Alternator.
Spark plugs and HT leads.
Ignition coil and mounting bracket.
Oil pressure warning lamp switch.
Oil filter.
Dipstick and tube.
Engine mounting brackets.
Clutch.
Alternator mounting bracket.Crankshaft speed/position sensor.
Engine lifting brackets.
Crankcase ventilation hose.
Examination and renovation
19Refer to Section 18 in Chapter 2, PartA.
Reassembly
20Refer to paragraphs 12 to 16 but note that
new rocker arm nuts will be required, if they
have been removed.
Note: The belt tension should be checked
using Ford special tool No 21-113 after
refitting. A suitable puller may be required to
remove the sprockets. If the camshaft
sprocket is removed, a new retaining bolt
must be used on refitting, and suitable sealant
(Loctite 74 or 274, or Omnifit 30M blue) will be
required to coat the bolt threads.
1.8 litre (R2A type)
Removal
1If the engine is in the vehicle, carry out the
following operations:
a)Disconnect the battery negative lead
b)Remove the alternator drivebelt
c)Remove the distributor cap, rotor arm and
housing
d)Disconnect the wiring plug from the
crankshaft speed/position sensor
e)Unclip the coolant hoses from the timing
cover, and position them across the top
of the camshaft cover out of the way
f)If desired for improved access, remove
the fan shroud and cooling fan assembly,
although this is not essential
2Slacken the crankshaft pulley bolt. Prevent
the crankshaft from turning by engaging top
gear (manual gearbox only) and having an
assistant apply the brake pedal hard, or by
removing the starter motor and jamming the
ring gear teeth with a lever.
3Remove the bolt and washer and withdraw
the pulley (see illustration). If the pulley will
not come off easily, refit the bolt part way and
use a puller, but take care not to damage the
sensor toothed disc.
18Timing belt and sprockets -
removal and refitting
17Engine dismantling,
examination, renovation and
reassembly - general information
2C•10CVH engines
17.10 Removing the oil pressure warning
lamp switch - 1.8 litre (R2A)
18.5 Withdrawing the timing cover -
1.8 litre (R2A)18.3 Withdrawing the crankshaft pulley -
1.8 litre (R2A)

4Unscrew the two timing cover securing
nuts, and recover the earth tag and the
coolant hose clip.
5Unscrew the two securing bolts and
withdraw the timing cover (see illustration).
6Refit the crankshaft pulley bolt, and using a
socket on the bolt, turn the engine clockwise
until the TDC (top dead centre) lug on the
crankshaft sprocket is uppermost, and in line
with the notch in the oil pump flange, and the
pointer on the camshaft sprocket is aligned
with the dot on the cylinder head front face
(see illustrations).
7Loosen the two timing belt tensioner bolts,
press the tensioner to the left against the
spring tension, and tighten the two bolts to
retain the tensioner in the released position.
8Mark the running direction of the belt if it is
to be re-used, then slip it off the sprockets,and withdraw the belt (see illustration).
9If desired, the camshaft and crankshaft
sprockets can be removed as follows,
otherwise proceed to paragraph 19. The
coolant pump sprocket is integral with the
pump and cannot be removed separately.
10Unscrew the crankshaft pulley bolt,
preventing the crankshaft from turning as
before if necessary, then remove the
crankshaft sprocket. Refit the bolt part way
and use a puller if necessary. Recover the
Woodruff key from the end of the crankshaft
and remove the thrustwasher (see
illustrations).
11Unscrew the camshaft sprocket bolt while
holding the sprocket stationary with a 41 mm
ring spanner. Alternatively, make up a tool
similar to that shown for tightening the bolt
and hold the sprocket using two boltsengaged in the sprockets holes. Recover the
distributor rotor shaft which is held in place by
the camshaft sprocket bolt (see illustration).
12Remove the camshaft sprocket, refitting
the bolt part way and using a puller if
necessary (see illustration).
13If desired, the timing belt backplate can
be removed by lifting it from the studs (see
illustration)and the timing belt tensioner and
coolant pump can be removed.
14If required, the camshaft oil seal can be
removed using self-tapping screws and a pair
of grips. A new seal can be fitted using a
suitable tube drift to press it into place.
Lubricate the seal lips with clean engine oil
before installation.
Refitting
15Refit the sprockets as follows.
CVH engines 2C•11
2C
18.8 Withdrawing the timing belt -
1.8 litre (R2A)
18.13 Removing the timing belt backplate -
1.8 litre (R2A)18.12 Using a puller to remove the
camshaft sprocket - 1.8 litre (R2A)18.11 Removing the camshaft sprocket
bolt and distributor rotor shaft -
1.8 litre (R2A)
18.10c . . . and the thrustwasher -
1.8 litre (R2A)18.10b . . . the Woodruff key . . .18.10a Remove the crankshaft
sprocket . . .
18.6b TDC pointer on camshaft sprocket
aligned with dot on cylinder head -
1.8 litre (R2A)18.6a TDC lug on crankshaft sprocket
aligned with notch in oil pump flange -
1.8 litre (R2A)

16Where applicable, refit the timing belt
tensioner and coolant pump, locate the timing
belt backplate over the studs, then fit the
camshaft sprocket and the distributor rotor
shaft.
17The camshaft sprocket bolt must be
coated with sealant before installation. The
manufacturers recommend Loctite 74 or 274,
or Omnifit 30M blue. With the sealant applied,
insert the bolt, hold the camshaft sprocket
stationary as during removal, and tighten the
bolt to the specified torque (see illustration).
18Refit the thrustwasher with the convex
side facing forwards, and refit the Woodruff
key, then refit the crankshaft sprocket with the
“FRONT” mark facing forwards.
19Fit the timing belt over the crankshaft
sprocket, but do not engage it with the other
sprockets yet. Be careful not to kink the belt,
and if the old belt is being refitted, observe the
previously noted running direction.20Make sure that the TDC pointer on the
camshaft sprocket is still aligned with the dot
on the cylinder head front face.
21Check that the TDC lug on the crankshaft
sprocket is still in line with the notch in the oil
pump flange. If necessary, refit the crankshaft
pulley bolt, if not already done, and using a
socket on the bolt, turn the crankshaft by the
shortest possible route to align the lug and
notch.
22Starting at the crankshaft and working in
an anti-clockwise direction, fit the timing belt
over the camshaft sprocket, round the
tensioner roller, and over the coolant pump
sprocket.
23Slacken the tensioner bolts, allow the
tensioner roller to rest against the belt, then
tighten the tensioner bolts.
24Refit the crankshaft pulley bolt, if not
already done, and using a socket on the bolt,
turn the engine through two revolutions in a
clockwise direction (to bring No 1 cylinder
back to TDC), then turn the crankshaft 60º
anti-clockwise (No 1 cylinder at 60º BTDC).
25The belt tension should now be checked
by applying Ford tension gauge, tool No 21-
113 to the longest belt run. Desired gauge
readings are:
Used belt - 4 to 6
New belt - 10 to 11
If the tension gauge is not available, a rough
guide is that the belt tension is correct when
the belt can be twisted 90º in the middle of the
longest run with the fingers using moderate
pressure (see illustration). In this case, the
vehicle should be taken to a Ford dealer so
that the belt tension can be checked using the
special gauge at the earliest opportunity.
26If adjustment of belt tension is necessary,
turn the crankshaft clockwise to bring No 1
cylinder to TDC, then slacken the tensioner
bolts and move the tensioner to increase or
decrease the belt tension. Tighten the
tensioner bolts to the specified torque.
27Turn the crankshaft 90º clockwise past
TDC, then anti-clockwise back to the 60º
BTDC position (No 1 cylinder at 60º BTDC).
Check the belt tension again (see
illustration).28Repeat the procedure given in paragraphs
26 and 27 until the belt tension is correct.
29Refit the timing cover and secure with the
two bolts and nuts. Ensure that the earth tag
and the coolant hose clip are fitted under the
relevant nuts (see illustration).
30Unscrew the crankshaft pulley bolt, then
refit the crankshaft pulley and the bolt and
washer. Tighten the crankshaft pulley bolt to
the specified torque, preventing the
crankshaft from turning as described in
paragraph 2.
31If the engine is in the vehicle, reverse the
operations described in paragraph 1.
1.6 and 1.8 litre (R6A type)
32If the engine is in the vehicle, carry out the
following operations.
a)Disconnect the battery negative lead.
b)Remove the alternator drivebelt.
c)Disconnect the HT leads from the spark
plugs, noting their locations; detach the
HT lead bracket from the camshaft cover,
and position the leads out of the way.
d)Move the coolant hoses from the front of
the timing cover, and position them
across the top of the camshaft cover out
of the way.
e)If desired for improved access, remove
the fan shroud and the cooling fan
assembly, although this is not essential.
33Proceed as described in paragraphs 2 to
30 inclusive, noting the following differences
for the 1.6 litre engine (see illustrations).
a)There is no sensor toothed disc on the
crankshaft pulley.
b)A two-piece timing cover is fitted,
consisting of upper and lower sections,
each secured by two bolts. No earth tag
or coolant hose clip is fitted to the bolts.
c)The TDC datum on the oil pump takes the
form of a lug instead of a notch.
d)There is no distributor rotor shaft fitted to
the camshaft sprocket bolt.
e)There is no timing belt backplate.
34On completion, if the engine is in the
vehicle, reverse the operations given in
paragraph 32.
2C•12CVH engines
18.17 Tightening the camshaft sprocket
bolt. Hold the sprocket stationary using an
improvised tool with two bolts engaged in
the sprocket holes - 1.8 litre (R2A)
18.27 No 1 cylinder at 60°BTDC for
checking of timing belt tension -
1.8 litre (R2A)
18.29 Earth tag (1) and coolant hose clip (2)
locations on timing cover -
1.8 litre (R2A)
18.25 Twisting the timing belt to assess its
tension - 1.8 litre (R2A)

leaving the wires, hoses, pipes and cables
connected. However, care must be taken not
to strain any of the wires, hoses or cables.
31Disconnect the exhaust gas oxygen
sensor wiring connector (see illustration)
then unscrew the three securing bolts and
disconnect the exhaust downpipe from the
manifold flange. Recover the gasket.
32If desired, remove the exhaust manifold.
33If the inlet manifold is to be removed with
the cylinder head, disconnect all relevant
wires, hoses, pipes and cables, otherwise
unbolt the manifold and move it to one side,
ensuring that it is adequately supported.
34Note the information given in paragraphs
18 to 21 inclusive of Section 20.
Refitting
35With the cylinder head refitted, proceed
as follows.
36Refit the manifolds and/or reconnect all
wires, hoses, pipes and cables as applicable.
37Reconnect the exhaust downpipe to the
manifold using a new gasket, and reconnect
the exhaust gas oxygen sensor wiring
connector.
38Reconnect the earth lead to the battery
tray.
39Refit the spark plugs and reconnect the
HT leads.
40Refit the air cleaner.
41Reconnect the coolant hoses to the
thermostat housing and cylinder head.
42Fill the cooling system.
43Reconnect the battery negative lead.Note: The cylinder head bolts must always be
renewed after slackening, and a new cylinder
head gasket and camshaft cover gasket must
be used on refitting. If the engine has recently
run, the cylinder head must be allowed to cool
to room temperature before it is removed.
1.8 litre (R2A type)
Removal
1With the manifolds removed, proceed as
follows.
2Remove the timing belt, camshaft sprocket,
and timing belt backplate.
3Disconnect the crankcase ventilation hose
from the camshaft cover.
4Unscrew the nine securing bolts and
remove the camshaft cover and gasket (see
illustration).
5Unscrew the ten cylinder head bolts half a
turn at a time in the reverse order to that
shown for tightening.
6With the bolts removed, lift the cylinder
head from the block (see illustration). If the
cylinder head is stuck, tap it free with a
wooden mallet. Do not insert a lever into the
joint between the cylinder head and block as
this may result in damage to the mating faces.
Place the cylinder head on blocks of wood to
prevent damage to the valves.7Recover the gasket, and the locating
dowels if they are loose (see illustration).
Refitting
8Commence refitting as follows.
9Turn the crankshaft so that No 1 piston is
approximately 20.0 mm (0.8 in) before TDC.
This precaution will prevent any damage to
open valves.
10Make sure that the mating faces of the
cylinder block and cylinder head are perfectly
clean, then refit the locating dowels to the
block where applicable, and locate a new
gasket over the dowels with the red sealing
bead and the “1.8” mark uppermost (see
illustrations). Do not use jointing compound.
11Turn the camshaft so that the TDC pointer
on the camshaft sprocket is aligned with the
dot on the cylinder head front face.
12Lower the cylinder head onto the gasket,
making sure that the locating dowels engage.
13Insert the new cylinder head bolts into
their locations in the cylinder head, then
tighten the bolts in the order shown to the five
stages given in the Specifications (see
illustrations).
14Fit a new camshaft cover gasket to the
cylinder head, ensuring that the gasket
locates correctly over the edges of the
cylinder head (see illustration).
15Refit the camshaft cover and tighten the
bolts evenly, ensuring that the studded bolts
which retain the HT lead clips are refitted to
their correct positions (see illustration).
20Cylinder head - removal and
refitting (engine removed)
2C•14CVH engines
19.31 Disconnecting the exhaust gas
oxygen sensor wiring connector -
1.6/1.8 litre (R6A)20.6 Withdraw the cylinder head bolts and
lift the cylinder head from the block -
1.8 litre (R2A)
20.10b . . . then locate a new gasket with
the red sealing bead and “1.8” mark
uppermost - 1.8 litre (R2A)20.10a Fit the locating dowels (arrowed) to
the block . . .20.7 Recover the cylinder head gasket -
1.8 litre (R2A)
20.4 Remove the camshaft cover and
gasket - 1.8 litre (R2A)

16Reconnect the crankcase ventilation hose
to the camshaft cover.
17Refit the timing belt backplate, camshaft
sprocket and timing belt.
1.6 and 1.8 litre (R6A type)
18With the manifolds removed, proceed as
follows.
19Remove the timing belt.
20Proceed as shown in paragraphs 3 to 16
inclusive, noting the following differences for
the 1.6 litre engine only:
a)Unscrew the cylinder head bolts in the
reverse order to that shown for tightening.
b)The cylinder head gasket is identified by a
single tooth on its edge, and the gasket
must be fitted with the tooth nearest theoil filter end of the engine, as shown (see
illustration).
c)Tighten the cylinder head bolts in the
order shown (see illustration), to the four
stages given in the Specifications at the
beginning of this Chapter.
d)Ignore the reference to the studded
camshaft cover bolts.
21On completion, refit the timing belt.
Note: A valve spring compressor will be
required during this procedure. New valve
stem oil seals should be used on
reassembly.
1.8 litre (R2A type)
Dismantling
1With the cylinder head removed, remove
the camshaft.
2Using a valve spring compressor, compress
one of the valve springs until the split collets
can be removed from the grooves in the valve
stem. Release the compressor and remove
the cap and spring, identifying them for
location. If the cap is difficult to release, do
not continue to tighten the compressor, but
gently tap the top of the tool with a hammer.
Always make sure that the compressor is
firmly located on the valve head and the cap
(see illustrations).
3Prise the oil seal from the valve stem, and
remove the spring seat, then withdraw the
valve (see illustrations).
21Cylinder head - dismantling
and reassembly
CVH engines 2C•15
2C
20.14 Ensure that the camshaft cover
gasket locates over the edges of the
cylinder head - 1.8 litre (R2A)
21.2c . . . then remove the cap and spring -
1.8 litre (R2A)21.2b . . . to free the split collets . . .
20.20b Cylinder head bolt tightening
sequence - 1.6 litre20.20a Cylinder head gasket correctly
located - 1.6 litre
A Locating dowelsB Identification teeth
21.2a Compress the valve spring . . .
20.13b Tighten the cylinder head bolts
using an angle gauge - 1.8 litre (R2A)20.13a Cylinder head bolt tightening
sequence - 1.8 litre (R2A)
20.15 Fit the camshaft cover, ensuring that
the studded bolts (arrowed) are correctly
located - 1.8 litre (R2A)