warning FORD SIERRA 1993 2.G Fuel And Exhaust Systems Fuel Injection Workshop Manual

working on the exhaust system, ensure
that the converter is well clear of any
jacks or other lifting gear used to raise the
car and do not drive the car over rough
ground, road humps, etc., in such a way
as to “ground” the exhaust system.
j)In some cases, particularly when the car is
new and/or is used for stop/start driving, a
sulphurous smell (like that of rotten eggs)
may be noticed from the exhaust. This is
common to many catalytic converter-
equipped cars and seems to be due to the
small amount of sulphur found in some
petrols reacting with hydrogen in the
exhaust to produce hydrogen sulphide
(H2S) gas; while this gas is toxic, it is not
produced in sufficient amounts to be a
problem. Once the car has covered a few
thousand miles the problem should
disappear - in the meanwhile a change of
driving style or of the brand of petrol used
may effect a solution.
k)The catalytic converter, used on a well-
maintained and well-driven car, should
last for between 50 000 and 100 000
miles - from this point on, careful checks
should be made at all specified service
intervals of the CO level to ensure that the
converter is still operating efficiently - if
the converter is no longer effective it must
be renewed.
EEC IV module - warning
Following disconnection of the battery, the
information stored in the EEC IV module
memory will be erased. After reconnecting the
battery, the engine should be allowed to idle for
three minutes. Once the engine has reached
normal operating temperature, the idle speed
should be increased to 1200 rpm and
maintained for approximately 2 minutes, which
will allow the module to “re-learn” the optimum
idle values. It may be necessary to drive the
vehicle in order for the module to “re-learn” the
values under load. The module should complete
its learning process after approximately 5 miles
(8 kilometres) of varied driving.
Refer to Chapter 1, Section 38.
2.0 litre SOHC models
1Disconnect the battery negative lead.
2Depress the locking clip on the airflow
meter wiring plug and disconnect the plug.
Pull on the plug, not the wiring.
3Loosen the securing clip and disconnect
the air inlet hose from the airflow meter.
4Release the four securing clips and lift off
the air cleaner lid with the airflow meter.
5Remove the left-hand front wheel arch liner.
6Working under the wheel arch, unscrew the
three air cleaner securing nuts and washers.
7Disconnect the air inlet tube, and withdrawthe air cleaner from the engine compartment.
8Refitting is a reversal of removal.
2.0 litre DOHC models
9Disconnect the battery negative lead.
10Disconnect the wiring plug from the idle
speed control valve at the front of the plenum
chamber.
11Loosen the clamp, and detach the air inlet
hose from the air inlet tubing.
12Unscrew the securing nut, and release the
air inlet tube from the bracket on the engine
compartment front panel.
13Release the air cleaner lid securing clips,
then lift away the air inlet tube, plenum
chamber and air cleaner lid as an assembly,
disconnecting the breather hose from the air
inlet tube.
14Lift out the air cleaner element then wipe
the inside of the air cleaner lid and casing clean.
15Remove the left-hand front wheel arch liner.
16Working under the wheel arch, unscrew the
three air cleaner securing nuts and washers.
17Disconnect the air inlet tube, and
withdraw the air cleaner from the engine
compartment.
18Refitting is a reversal of removal.
1.6 and 1.8 litre (R6A type) CVH
models
1.6 litre
19Remove the screws from the top of the air
cleaner cover.
20Disconnect the cold air inlet hose from the
air cleaner spout or the inlet on the front body
panel. The hose is secured by toggle clips.
21Disconnect the hot air inlet hose from the
air cleaner spout or the hot air shroud on the
exhaust manifold.
22Where applicable, remove the screw
securing the air cleaner body to the camshaft
cover.
23Withdraw the air cleaner and disconnect
the breather hose from the camshaft cover.
24Refitting is a reversal of removal, ensure
the disturbed hoses are securely connected.
1.8 litre
25Undo the two nuts, lift off the air cleaner
cover, and remove the element.26Disconnect the engine breather hose and
the oil separator hose, then undo the three
nuts and lift up the air cleaner casing (see
illustrations).
27Disconnect the yellow striped vacuum
hose from the underside of the casing, detach
the air inlet hose, and remove the air cleaner
assembly.
28Refitting is a reversal of removal, ensuring
all hoses are correctly attached.
1Disconnect the battery negative lead.
2Remove the air cleaner assembly.
3Position a suitable container (or a sufficient
quantity of absorbent cloth) beneath the fuel
inlet connection on the CFI unit.
4Use an open-ended spanner on the flats of
the inlet union screwed into the CFI unit, to
prevent it from turning while the inlet pipe
union is loosened (see illustration). Allow all
pressure/fuel seepage to dissipate before fully
unscrewing the union if it is to be
disconnected, or tightened if another part of
the system is to be worked on.
4Fuel system (1.6 and 1.8 litre
(R6A type) CVH) - depressurisation
3Air cleaner - removal and
refitting
2Air cleaner element - renewal
4B•4Fuel and exhaust systems - fuel injection
3.26b Air cleaner casing attachments - 1.8
litre (R6A) CVH
A Casing retaining nuts (arrowed)
B Vacuum hose (arrowed)
3.26a Air cleaner cover and hose
attachments - 1.8 litre (R6A) CVH
A Cover retaining nuts
B Engine breather hose
C Oil separator hose
Remember to depressurise the
fuel system before loosening any
connections.
Refer to the precautions in
Section 1 before proceeding. The fuel
system will remain pressurised after the
engine is switched off.
4.4 CFI unit fuel inlet union (arrowed)

4Remove the three screws securing the
motor and the throttle position sensor
assembly mounting bracket to the CFI unit,
and withdraw the assembly.
5Remove the three motor securing screws,
and withdraw the motor from the bracket.
6Refitting is a reversal of removal, bearing in
mind the following points.
7Ensure that the throttle position sensor
actuating arm locates correctly on the throttle
valve spindle, and that the mounting bracket
aligns with its locating pegs.
8On completion, the idle speed should be
checked by a Ford dealer at the earliest
opportunity.
1.8 litre
9Disconnect the battery negative lead.
10Remove the air cleaner assembly.
11Disconnect the wiring connector from the
throttle valve control motor.
12Remove the three screws securing the
motor and the mounting bracket to the CFI
unit, and withdraw the assembly.
13Remove the three motor securing screws,
and withdraw the motor from the bracket.
14Refitting is a reversal of removal, ensuring
that the motor is located on the throttle
linkage, and that the bracket and locating
pegs are aligned.
Note: A tachometer and an exhaust gas
analyser will be required to check the idle
mixture on completion. A new gasket must be
used when refitting the throttle body.
2.0 litre SOHC models
1Disconnect the battery negative lead.
2Free the throttle position sensor wiring plug
from the retaining clip on the underside of the
throttle body. Disconnect the wiring plug
halves by releasing the locktabs and pulling
on the plug halves, not the wiring.
3Disconnect the throttle cable from the lever.
4Disconnect the crankcase ventilation hose
from the air inlet hose, then disconnect the air
inlet hose from the throttle body and the
airflow meter.
5Remove the four securing bolts and
withdraw the throttle body from the inlet
manifold. Recover the gasket.
6Refitting is a reversal of removal, bearing in
mind the following points.
7Ensure that all mating faces are clean, and
fit a new gasket.
8When reconnecting the air inlet hose, make
sure that the hose clips are correctly aligned,
see illustration, Section 15.
9On completion, adjust the throttle cable and
check and if necessary adjust the idle mixture.
2.0 litre DOHC models
10Disconnect the battery negative lead.
11Free the throttle position sensor wiring
plug from the retaining clip located on the
underside of the throttle body. Disconnect thewiring plug halves by releasing the locktabs
and pulling on the plug halves, not the wiring.
12Disconnect the throttle cable from the
linkage.
13Loosen the securing clip, and disconnect
the air inlet hose from the throttle body.
14Unscrew the four securing bolts, and
withdraw the throttle body from the inlet
manifold. Recover the gasket.
15Refitting is a reversal of removal, bearing
in mind the following points.
16Ensure that the mating faces of the
throttle body and the inlet manifold are clean,
and fit a new gasket.
17On completion, adjust the throttle cable.
Where applicable, check and if necessary
adjust the idle mixture.
Note: A tachometer and an exhaust gas
analyser will be required to check the idle
mixture on completion. A new gasket must be
used when refitting the manifold.
2.0 litre SOHC models
1Disconnect the battery negative lead.
2Partially drain the cooling system.
3Disconnect the crankcase ventilation hose
from the air inlet hose. Disconnect the air inlethose from the inlet manifold and the airflow
meter.
4Disconnect the HT lead from the coil, then
remove the distributor cap and position the
cap and HT leads clear of the inlet manifold
assembly.
5Unscrew the two securing bolts and remove
the throttle cable bracket (see illustration).
Disconnect the cable end from the throttle
lever, and move the bracket to one side.
6Disconnect the fuel injection harness wiring
plugs at the bulkhead end of the manifold
(see illustration).
7Disconnect the oil pressure warning lamp
switch wire from below the manifold.
8Disconnect the fuel supply hose from the
fuel rail. Loosen the union nut slowly to relieve
the pressure in the fuel system, and be
prepared for petrol spillage.
9Disconnect the fuel return hose from the
fuel pressure regulator. Be prepared for fuel
spillage.
10Disconnect the coolant hose and the
brake servo vacuum hose from the inlet
manifold.
11Unscrew the two securing nuts and
remove the bracing strut which runs from the
manifold to the right-hand side of the cylinder
head (see illustration).
12Unscrew the two bolts securing the lower
manifold bracket to the left-hand side of the
cylinder block (see illustration).
13Remove the four bolts and two nuts
securing the inlet manifold to the cylinder
head, and carefully withdraw the manifold. If
the distributor obstructs removal, extract the
front manifold stud by locking two nuts
30Inlet manifold - removal and
refitting
29Throttle body - removal and
refitting
4B•12Fuel and exhaust systems - fuel injection
30.5 Unscrew the securing bolts and
remove the throttle cable bracket
30.12 Lower inlet manifold bracket
(arrowed)30.11 Unscrew the two securing nuts
(arrowed) and remove the inlet manifold
bracing strut
30.6 Disconnecting a fuel injection harness
wiring plug
Caution: Refer to the
precautions in Section 1 before
proceeding.