light GENESIS G70 2023 Service Manual
[x] Cancel search | Manufacturer: GENESIS, Model Year: 2023, Model line: G70, Model: GENESIS G70 2023Pages: 552, PDF Size: 8.46 MB
Page 136 of 552
Convenience Features5-8
Remotely starting vehicle
You can start the vehicle using the
Remote Start button (5) on the smart key.
To start the vehicle remotely:
1. Press the door lock button on the smart key within 32 feet (10 m) from
the vehicle.
2. Press the Remote Start button (5) for more than 2 seconds within 4 seconds
after pressing the door lock button.
3. The hazard warning lights will blink and the engine will start.
4. To turn off the remote start function, press the Remote Start button (5)
once.
Information
[ The vehicle must be in P (Park) for the
remote start function to start.
[ The engine turns off if you enter the
vehicle without a registered smart key.
[ The engine turns off if you do not get
in the vehicle within 10 minutes after
remotely starting the vehicle.
[ The Remote Start button (5) may not
operate if the smart key is not within
32 feet (10 m).
[ The vehicle will not remotely start if the
engine hood or trunk is opened.
[ Do not idle the engine for a long period.
[ Do not operate remote start in closed
areas where there is no ade uate
ventilation for the engine exhaust.
Turning on the lamps
If the lamp on button (6) is pushed, the
headlights and tail lamps are turned
on. However, it works only when the
following conditions are satisfied:
[ The vehicle is turned off.
[ The doors are locked.
[ The light control switch is in the AUTO
headlight position (The headlights and
tail lamps will turn on when it is dark.)
or in the Headlight position.
Start-up
You can start the vehicle without
inserting the key.
For more details, refer to the “Engine
Start/Stop Button” section in chapter 6.
Information
If the smart key is not moved for some
time, the detection function for smart key
operation will pause. ift the smart key to
activate the detection again.
NOTICE
To prevent damaging the smart key:
[ Keep the smart key in a cool,
dry place to avoid damage or
malfunction. Exposure to moisture
or high temperature may cause
the internal circuit of the smart key
to malfunction which may not be
covered under warranty.
[ Avoid dropping or throwing the
smart key.
[ Protect the smart key from extreme
temperatures.
Page 145 of 552
05
5-17
The icon will be highlighted or an alarm
and vibration will also be provided when
the selected icon function is being
performed.
After the Digital Key App and vehicle are
connected, if Digital Key App remote
control is not used over 5 minutes, the
connection between the app and vehicle
will disconnect automatically.
Note that you cannot lock your vehicle
using Genesis Digital Key APP if any of
the following occurs: - The Engine Start/Stop button is in the ACC or ON position
- Door(s) is open
[ Remotely starting vehicle with the
Digital Key App
1. Press the Door Lock button in Genesis Digital Key App.
2. Press the Remote Engine On icon within 4 seconds.
3. The hazard warning lights will blink and the engine will start.
- Unless the driver puts the registered digital key (smart phone)
on the in-vehicle authentication
pad (wireless charging pad) when
the Remote Start function is on, the
engine will turn off.
- If the driver does not get in the vehicle within 10 minutes after
the engine is remotely started, the
engine will turn off.
CAUTION
[ If the vehicle windows are tinted
with a film containing metallic
substances, it may cause poor
Bluetooth connection and poor
performance of the Digital Key App. [
If multiple users use the digital key
at the same time, the functions of
the Digital Key App may not work
properly. Only the necessary user
should operate the Digital Key App
remote control.
[ When using the Digital Key App
remote control, the driver (the
remote control user) should leave
the vehicle after checking that the
doors are locked. When the doors are
locked, the chime will sound and the
hazard warning lights will blink once.
[ The remote functions of the Digital
Key App enable the vehicle to be
controlled when the user is within
operating range. If the digital key
is out of the operating range, the
remote control function may not
operate properly.
[ If the smart phone is moved
away from the vehicle while the
smart phone and the vehicle are
connected, Digital Key App remote
control may not operate properly.
[ When using Digital Key App
remote control via Bluetooth,
communication may be slow or the
operating range may be reduced in
the following circumstances:
- Smart phone mobile data is weak
- Bluetooth connection is weak due
to many Bluetooth devices
- There is an object such as metal or
concrete between the vehicle and
smart phone
- The smart phone is wrapped in
your hand or other electronic
devices that cause interference is
placed near the smart phone
[ If you use a smart phone cover that
uses wireless communication or is
made of metal, the digital key NFC
function may not work properly.
Remove the smart phone cover
before using the digital key NFC
function.
Page 149 of 552
05
5-21
Note that you cannot lock your vehicle
using the NFC antenna if any of the
following occur: - The Smart Key is in the vehicle
- The Engine Start/Stop button is in ACC or ON position
- Any of the doors are open except for the engine hood or trunk
[ Starting the engine
After placing your registered card key
on the in-vehicle authentication pad
(wireless charger pad), depress the brake
pedal and press the Engine Start/ Stop
button.
For more details, refer to the “Engine
Start/Stop Button” section in chapter 6.
WARNING
The engine can be started when the
registered card key is placed on the
in-vehicle authentication pad (wireless
charging pad). Therefore, do not leave
unsupervised children or people who
are not aware of the system since it
can result in serious injury or death. In
addition, always have the registered
card key with you to prevent vehicle
theft when leaving the vehicle.
CAUTION
[ The digital key (card key) may not
work under the following conditions:
- The card key is not touching
the center of the door handle
authentication pad or in-vehicle
authentication pad (wireless
charging pad) correctly.
- The card key is used overlapped
with NFC-enabled cards such as
credit card or smart phone.
- If the card key does not work,
move the card key approximately
4 in. (10 cm) away from the
authentication pad and then touch
it again.
[ The card key can be damaged by
impacts. If the key is damaged,
replace the card key with a new one
and register it again.
[ Long-time exposure to high
temperature may cause the card
key to malfunction. Be careful not to
expose the key to direct sunlight or
high temperature.
[ The card key is consumable and it
is not covered by your warranty.
Therefore, the result of misuse by
customers such as breakage or loss is
not guaranteed.
[ Always have the card key with you
when leaving the vehicle. If the
authenticated phone has a dead
battery, or it is lost or stolen, you may
be locked out of the vehicle.
Page 154 of 552
Convenience Features5-26
Operating Door Locks from
Outside the Vehicle
Mechanical key
OIKSB051283L
In order to operate door lock by using
mechanical key, turn the key after
removing the cover.
To remove the cover :
1. Pull out the door handle.
2. Press the lock located at the bottom of the cover with a key or flat-head
screwdriver (1).
3. Push out the cover (2) while pressing the lock.
After removing the cover, turn the key
counterclockwise to lock (A) or turn the
key clockwise to unlock (B).
If you lock/unlock the driver’s door with
a mechanical key, the door of driver will
lock/unlock automatically, not others.
Namely, the driver’s door and the rest of
the doors are not interlocked in terms of
mechanical key.
Once the doors are unlocked, they may
be opened by pulling the door handle.
When closing the door, push the door by
hand. Make sure that doors are closed
securely.
NOTICE
Do not apply excessive force on the
door and door handle. It may damage
the door and door handle.
Information
When the keyhole freezes and does
not open, lightly tap or indirectly warm
(for example, hand temperature) the
keyhole.
Smart key
OIKSB051281L
ock
Touch the touch sensor on the front
outside door handle (
the engraved part)
while carrying the Smart Key with you or
press the Door Lock button on the Smart
Key, all doors will lock.
DOOR LOCK
Page 159 of 552
05
5-31
This system helps to protect your vehicle
and valuables. The horn will sound and
the hazard warning lights will blink
continuously if any of the following
occur: - A door is opened without using the smart key.
- The trunk is opened without using the smart key.
- The engine hood is opened.
The alarm continues for 30 seconds, then
the system resets. To turn off the alarm,
unlock the doors with the smart key.
The Theft Alarm System automatically
sets 30 seconds after you lock the doors
and the trunk. For the system to activate,
you must lock the doors and the trunk
from outside the vehicle with the smart
key or by touching the touch sensor on
the outside of the door handle with the
smart key in your possession.
The hazard warning lights will blink and
the chime will sound once to indicate the
system is armed.
Once the security system is set, opening
any door, the trunk, or the hood without
using the smart key will cause the alarm
to activate.
The Theft Alarm System will not set if the
hood, the trunk, or any door is not fully
closed. If the system will not set, check
the hood, the trunk, or the doors are fully
closed.
Do not attempt to alter this system or
add other devices to it. Information
[ Do not lock the doors until all
passengers have left the vehicle. If the
remaining passenger leaves the vehicle
when the system is armed, the alarm
will be activated.
[ If the vehicle is not disarmed with the
smart key, open the doors by using the
mechanical key and start the engine by
G L U H F W O \ S U H V V L Q J W K H ( Q J L Q H 6 W D U W 6 W R S
button with the smart key.
[ If the system is disarmed by unlocking
the vehicle, but neither a door or the
trunk is opened within 30 seconds, the
doors will relock and the system will
rearm automatically.
7 + ( ) 7
Page 163 of 552
05
5-35
Motor Driven Power Steering
(MDPS)
The system assists you with steering the
vehicle. If the vehicle is turned off or
if the power steering system becomes
inoperative, you may still steer the
vehicle, but it will require increased
steering effort.
Should you notice any change in the
effort required to steer during normal
vehicle operation, we recommend that
you have the system checked by an
authorized retailer of Genesis Branded
products.
CAUTION
If Motor Driven Power Steering does not
operate normally, the warning light
and the message ‘Check motor driven
power steering’ will illuminate on the
instrument cluster. You may steer the
vehicle, but it will require increased
steering efforts. We recommend that
you take the vehicle to an authorized
retailer of Genesis Branded products
and have the system checked as soon as
possible.
Information
The following symptoms may occur during
normal vehicle operation:
[ The steering effort may be high
immediately after pressing the Engine
6 W D U W 6 W R S E X W W R Q W R W K H 2 1 S R V L W L R Q
This happens as the system performs
W K H 0 ' 3 6 V \ V W H P G L D J Q R V W L F V : K H Q
the diagnostics is completed, the
steering wheel effort will return to its
normal condition.
[ : K H Q W K H E D W W H U \ Y R O W D J H L V O R Z \ R X
may have to put more steering effort.
owever, it is a temporary condition so
that it will return to normal condition
after charging the battery.
[ A click noise may be heard from the
0 ' 3 6 U H O D \ D I W H U W K H ( Q J L Q H 6 W D U W 6 W R S
button is in the ON or OFF position.
[ 0 R W R U Q R L V H P D \ E H K H D U G Z K H Q W K H
vehicle is at a stop or at a low driving
speed.
[ : K H Q \ R X R S H U D W H W K H V W H H U L Q J Z K H H O
in low temperatures, abnormal noise
may occur. If the temperature rises, the
noise will disappear.
This is a normal condition.
[ : K H Q D Q H U U R U L V G H W H F W H G I U R P 0 ' 3 6
the steering effort assist function will
not be activated in order to prevent
accidents. Instrument cluster warning
lights may be on or the steering effort
may be high. If these symptoms occur,
drive the vehicle to a safe area as soon
as it is safe to do so. ave the system
checked by an authori ed retailer of
Genesis Branded products as soon as
possible.
STEERING WHEEL
Page 164 of 552
Convenience Features5-36
Tilt/Telescopic Steering
When adjusting the steering wheel to a
comfortable position, adjust the steering
wheel so that it points toward your chest,
not toward your face. Make sure you can
see the instrument cluster warning lights
and gauges. After adjusting, push the
steering wheel both up and down to be
certain it is locked in position.
Always adjust the position of the steering
wheel before driving.
WARNING
[ NEVER adjust the steering wheel
while driving. This may cause loss
of vehicle control resulting in an
accident.
[ While adjusting the steering wheel
height, please do not push or pull
it hard since the fixture can be
damaged.
Manual adjustment
OIK050008
To adjust the steering wheel angle and
height:
1. Pull down the lock-release lever (1).
2. Adjust the steering wheel to the
desired angle (2) and distance
forward/back (3).
3. Pull up the lock-release lever to lock the steering wheel in place.
Information
Sometimes the lock release lever may not
engage completely. This may occur when
the gears of the locking mechanism do not
completely mesh. If this occurs, pull down
on the lock-release lever, read ust the
steering wheel again, and then pull back
up on the release lever to lock the steering
wheel in place.
Power adjustment
OIK050009
To change the steering wheel angle and
height:
[ Push the switch (1) up and down to
adjust the angle (2).
[ Push the switch forward or rearward
to adjust the height (3).
NOTICE
Do not adjust the steering wheel
longer than necessary when the
engine is turned off. This may result in
unnecessary battery drain.
Page 167 of 552
05
5-39
Inside Rearview Mirror
Before driving your vehicle, check to
see that your inside rearview mirror is
properly positioned. Adjust the rearview
mirror so that the view through the rear
window is properly centered.
WARNING
Make sure your line of sight is not
obstructed. Do not place objects in the
rear seat, cargo area, or behind the rear
headrests which could interfere with
your vision through the rear window.
WARNING
To prevent serious injury during an
accident or deployment of the air bag,
do not modify the rearview mirror and
do not install a wide mirror.
WARNING
NEVER adjust the mirror while driving.
This may cause loss of vehicle control
resulting in an accident.
NOTICE
When cleaning the mirror, use a paper
towel or similar material dampened
with glass cleaner. Do not spray glass
cleaner directly on the mirror as this
may cause the liquid cleaner to enter
the mirror housing.
Electrochromic Mirror (ECM)
OIK050210L
[A] : Indicator
Some vehicles come equipped with an
electrochromic mirror that helps control
glare while driving at night or under low
light driving conditions.
When the engine is running, the glare is
automatically controlled by the sensor
mounted in the rearview mirror. The
sensor detects the light level around the
vehicle, and automatically adjusts to
control the headlight glare from vehicles
behind you.
Whenever the the gear is shifted to R
(Reverse), the mirror will automatically
go to the brightest setting in order to
improve the driver’s view behind the
vehicle.
MIRRORS
Page 168 of 552
Convenience Features5-40
Electrochromic mirror (ECM) with
HomeLink® system and Genesis
Connected Service (if equipped)
Your vehicle may be equipped with
a Gentex Automatic-Dimming Mirror
with an Integrated HomeLink® Wireless
Control System.
During nighttime driving, this feature will
automatically detect and help reduce
rearview mirror glare. The HomeLink®
Universal Transceiver allows you to
activate your garage door(s), electric
gate, home lighting, etc.
OIK047082N
[A] : Telemetics buttons, [B] : HomeLink buttons,
[C] : HomeLink indicator
(1) HomeLink Channel 1
(2) HomeLink Channel 2
(3) HomeLink Channel 3
(4) Garage Door Opener Status Indicator : Closing or Closed
(5) HomeLink Operation Indicator
(6) Garage Door Opener Status Indicator : Opening or Opened
(7) HomeLink User Interface Indicator
$ X W R P D W L F ' L P P L Q J 1 L J K W 9 L V L R Q 6 D I H W \
Page 170 of 552
Convenience Features5-42
2) Programming a New HomeLink®
OIK040418N
1. Press and release the HomeLink button (1), (2) or (3), you would like
to program. The HomeLink indicator
light (7) will flash orange slowly (if
not, perform the steps of “Erasing
+ R P H / L Q N % X W W R Q VV V H F W L R Q D Q G V W D U W
over).
OIK040441N
2. Position the garage door opener remote 1 – 3 inches (2 – 8cm) away
from the HomeLink buttons.
3. While the HomeLink indicator light (7) is flashing orange, press and hold the
hand-held remote button. Continue
pressing the handheld remote button
until the HomeLink indicator light (7)
light changes from orange to green.
You may now release the handheld
remote button. 4. Wait until your garage door comes
to a complete stop, regardless of
position, before proceeding to the
next steps.
5. Press and release the HomeLink button you are programming and
observe the indicator light.
[ If the indicator light remains solid
green, your device should operate
when the HomeLink button is
pressed. At this point, if your device
operates, programming is complete.
[ If the indicator light rapidly
flashes green, firmly press, hold
for two seconds and release the
HomeLink button up to three times
in a row slowly to complete the
programming process. Do not press
the HomeLink button rapidly. At
this point if your device operates,
programming is complete. If the
device does not operate, continue
with step 6.
6. At the garage door opener motor, (security gate motor, etc.) locate the
"Learn", "Smart", "Set" or "Program"
button. This can usually be found
where the hanging antenna wire is
attached to the motor-head unit (see
the device's manual to identify this
button). The name and color of the
button may vary by manufacturer.