sensor GENESIS G90 2023 Manual Online

8-26
Emergency Situations
NOTICE
Do not let the compressor run for more
than 10 minutes, otherwise the device
will overheat and may be damaged.
Information
The pressure gauge may show higher than
actual reading when the compressor is
running. To get an accurate tire pressure,
the compressor needs to be turned off.
CAUTION
If the inflation pressure is not
maintained, drive the vehicle a second
time, refer to step 9.
Then repeat steps 10 to 13.
Use of the TMK may be ineffectual for
tire damage larger than approximately
0.16 in (4 mm).
We recommend that you contact an
authorized retailer of Genesis Branded
products if the tire cannot be made
roadworthy with the Tire Mobility Kit.
WARNING
The tire inflation pressure must be at
least 32 psi (220 kPa). If it is not, do not
continue driving.
Call for road side service or towing.
CAUTION
Tire pressure sensor (if equipped with
TPMS)
The sealant on the tire pressure sensor
and wheel should be removed when
you replace the tire with a new one
and inspect the tire pressure sensors.
Have you get this done at an authorized
retailer of Genesis Branded products.
Information
When reinstalling the repaired or replaced
tire and wheel on the vehicle, tighten the
wheel bolt to 101~116 lbf·ft (14~16 kgf·m).
008_RS4_HMA.indd 8-262022-04-18  3:48:14

9-51
09
Fuse NameFuse
RatingCircuit Protected
SBCM (DRV)20A Driver SBCM
CCU110A CCU
POWER
HANDLE15A Steering Tilt & Telescopic Unit
MODULE210AFront A/C Controller, Multifunction Switch, Head Lamp LH/
RH
MODULE910AMultifunction Switch, Data Link Connector, CCIC Keyboard,
Rain Sensor, Driver Power Window Switch, Driver Power
Outside Mirror Switch
CCU210A Stop Lamp Switch, CCU
A/C310AA/C Control Module, Front A/C Controller, Incar
Temperature Sensor, E/R Sub Junction Block (PTC Heater
#1/#2 Relay) Rear Junction Block (Rear Blower Relay)
MODULE310A IBU, IAU
IBU110A IBU, IAU
IBU210A IBU, BMS Control Module
E-SHIFTER210A Electronic ATM Shift Lever Dial
E-SHIFTER110A Electronic ATM Shift Lever Dial
MODULE1210ARear Corner Radar LH/RH, ECS Unit, Air ECS Unit, AWD
ECU, RWS Module, ADAS Unit (Parking), IBU, Crash Pad
Switch, Steering Tilt & Telescopic Unit, Front View Camera
(ADAS)
MODULE1110A Driver Power Window Switch, Multifunction Switch, IAU
AIR BAG215A SRS Control Module, Passenger Occupant Detection Sensor
AIR BAG115A SRS Control Module
MODULE1610AFront Console Mood Lamp #1/2, Garnish Lamp LH/RH,
Mood Lamp Unit, Roof Mood Lamp #1/2, Driver/Passenger
Door Garnish Mood Lamp, Rear Door Garnish Mood Lamp
LH/RH, ADAS Unit (Parking)
CLUSTER10A Instrument Cluster, Head-Up Display
MODULE1510A ADAS Unit (Driving)
Wireless DCU10A Domain Control Unit
MODULE510ARear Door Curtain, Rear Occupant Alert (ROA) Sensor,
Clock Spring, Front Console Switch, Active Air Flap Module,
Steering Tilt & Telescopic Unit

9-55
09
Engine compartment fuse panel
Fuse NameFuse
RatingCircuit Protected
IG130A IG1 Relay
ECU330A Engine Control Relay
IG230A IG2 Relay
ACC30A ACC Relay
ECU210A ECM
EWP20A Electronic Water Pump
MODULE110A Front Radar, Front Corner Radar LH/RH
MDPS210A MDPS Unit
IEB310A IEB Unit
TCU215A TCM, P/N Relay, Electronic Oil Pump
SENSOR310A Oxygen Sensor #1 (B1/S1), Oxygen Sensor #2 (B2/S1)
SENSOR210AOxygen Sensor #3 (B1/S2), Oxygen Sensor #4 (B2/S2),
Purge Control Solenoid Valve, Oil Pump Solenoid Valve,
Canister Close Valve, Oil Control Valve (Intake #1/#2), Oil
Control Valve (Exhaust #1/#2), RCV Control Solenoid Valve
#1/#2, E/R Junction Block (A/C Relay)
SENSOR110AE/R Junction Block (Fuel Pump Relay), Injector
#1/#2/#3/#4/#5/#6 (MPI)
IGN COIL15A Ignition Coil #1/#2/#3/#4/#5/#6
SENSOR415A Cooling Fan Motor, Electric Super Charging Unit (Signal)
ECU420A ECM
WASHER15A WASHER RELAY
MHSG10A[With Mild HEV] Mild Hybrid Starter & Generator Motor
(Signal)

9-61
09
Battery junction block
Fuse Name Fuse Rating Circuit Protected
LDC225A[Mild HEV] Battery System Assembly (Low DC-DC
Converter)
AMS10A 12V Battery Sensor
B+6100ARear Junction Block (Fuse - P/WINDOW (RH), BATTERY C/
FAN, P/SEAT (RR RH)1, P/SEAT (RR RH)2, S/HEATER (RR
RH), POWER TRUNK, RR DR CURTAIN, B+1)
B+560AICU Junction Block (Fuse - P/SEAT (PASS)1, P/SEAT
(PASS)2, MASSAGE SEAT (FRT), ADAS DRV1, S/HEATER
(PASS), CURTAIN, SUNROOF2, MODULE14)
B+460AICU Junction Block (Fuse - SBCM (DRV), SBCM (RR LH),
SUNROOF1, P/SEAT (DRV)1, P/SEAT (DRV)2, POWER
HANDLE, S/HEATER (DRV), P/WINDOW (LH))
B+8100ARear Junction Block (LDC, Fuse - PRESAFETY SEAT
BELT2, ECS1, ECS2, PRESAFETY SEAT BELT3, BATTERY
MANAGEMENT)
B+7100ARear Junction Block (Fuse -SBCM (PASS), SBCM (RR RH),
P/SEAT (RR LH)1, P/SEAT (RR LH)2, S/HEATER (RR LH),
MASSAGE SEAT (RR), BLOWER (RR), MODULE18, B+2, B+3)
RWS100A RWS Module
B+9125AE/R Junction Block (Fuse - HEAD LAMP LH, START, TCU1,
4WD, HEAD LAMP RH, ECU1, FUEL PUMP, ECU3)

9-68
Maintenance
High-pressure washing

[When using high-pressure washers,
make sure to maintain sufficient
distance from the vehicle.
Insufficient clearance or excessive
pressure can lead to component
damage or water penetration.

[Do not spray the camera, sensors or
its surrounding area directly with a
high pressure washer. Shock applied
from high pressure water may cause
the device to not operate normally.

[Do not bring the nozzle tip close to
boots (rubber or plastic covers) or
connectors as they may be damaged
if they come into contact with high
pressure water.
WARNING
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by water
before getting on the road. If braking
performance is impaired, dry the
brakes by applying them lightly while
maintaining a slow forward speed.
NOTICE

[Do not use strong soap, chemical
detergents or hot water, and do not
wash the vehicle in direct sunlight
or when the body of the vehicle is
warm.

[Be careful when washing the side
windows of your vehicle.

[Especially, with high-pressure water,
water may leak through the windows
and wet the interior.

[To prevent damage to the plastic
parts, do not clean with chemical
solvents or strong detergents.
NOTICE
ORS091047

[Water washing in the engine
compartment including high
pressure water washing may cause
the failure of electrical circuits
located in the engine compartment.

[Never allow water or other liquids
to come in contact with electrical/
electronic components inside the
vehicle as this may damage them.
NOTICE
Matte paint finish vehicle (if equipped)
Automatic car wash which uses rotating
brushes should not be used as this can
damage the surface of your vehicle. A
steam cleaner which washes the vehicle
surface at high temperature may cause
the oil to adhere and leave stains that is
difficult to remove.
Use a soft cloth (for example, microfiber
towel or sponge) when washing your
vehicle and dry with a microfiber towel.
When you hand wash your vehicle, you
should not use a cleaner that finishes
with wax.