clock HONDA ACCORD COUPE 2001 CF / 6.G User Guide

Cooling System

1. Make sure the engine and radiator
are cool.

2. Turn the radiator cap counter- clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.
3. Remove the radiator cap by
pushing down and turning

counterclockwise.

4. The coolant level should be up to the base of the filler neck. Add
coolant if it is low.
5. Put the radiator cap back on. Tighten it fully.
Maintenance
RADIATOR CAP

4-cylinder models 6-cylinder models

RADIATOR CAP
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Cooling System

1. Open the hood. Make sure the engine and radiator are cool to the

touch.

Except EX- V6 model

Turn the ignition ON (II). Turn the temperature control Dial all
the way clockwise. Turn off theignition and remove the key.
EX-V6 model

Turn the ignition ON (II). Turn the temperature control dial to90°F (32° C). Turn off the ignition
and remove the key.
2. Remove the radiator cap.
4-cylinder models

3. Loosen the drain plug on the bottom of the radiator. Thecoolant will drain through the
splash guard. Remove the drain
bolt and washer from the engine
block.

Maintenance
DRAIN

BOLT

DRAIN

PLUG

6-cylinder models
4-cylinder models

4-cylinder models

Spark Plugs (6-cylinder Models)
The spark plugs in your car should be replaced according to the timeand distance recommendations in
the maintenance schedule.
1. Loosen the two holding clips by turning the heads one-quarter turncounterclockwise with a flat-tippedscrewdriver. Remove the cover on
the front cylinder bank by pulling
it straight up. 2. Clean up any dirt and oil that have
collected around the ignition coils.
3. Disconnect the wire connector from the ignition coil by pushingon the lock tab and pulling on the
connector. Pull on the plastic connector, not the wires. 4. Use a wrench to remove the
hexagon socket head cap boltholding the ignition coil. Remove
the ignition coil by pulling it straight out.
5. Remove the spark plug with a five-eighths inch (16 mm) spark
plug socket.

Maintenance

Replacement
HEXAGON SOCKET HEAD CAP BOLT
HOLDING CLIP

Spark Plugs (6-cylinder Models)

6. Put the new spark plug into the socket; then screw it into the hole.
Screw it in by hand so you do not
crossthread it.
7. Torque the spark plug. (If you do not have a torque wrench, tighten
the spark plug two-thirds of a turn after it contacts the cylinder head.)
Tightening torque:
13 lbf .
ft (18 N .
m , 1.8 kgf .
m)

Tighten the spark plugs carefully. A
spark plug that is too loose can overheat and damage the engine.Overtightening can cause damage to
the threads in the cylinder head.
8. Install the ignition coil. Reinstall the hexagon socket head cap bolt. 9. Push the wire connector onto the
ignition coil. Make sure it locks in

place.

10. Repeat this procedure for the other five spark plugs.
11. Reinstall the cover on the front cylinder bank while putting its
mounting clip in the hole on the
passenger's side. Secure the cover
by turning the heads of the two holding clips one-quarter turn clockwise with a flat-tipped
screwdriver.

Specifications:
NGK:

DENSO:
PZFR5F-11

PKJ16CR-L11

Spark Plug Gap:
0.04 in
(1.1
mm)

Maintenance

NOTICE

Lights

Headlight Aiming

The headlights were properly aimed when your car was new. If youregularly carry heavy items in the
trunk, readjustment may be required.
Adjustment of the headlights should be performed by a Honda technicianor other qualified mechanic.
Replacing a Headlight Bulb
Your car has two bulbs on each side, four in total. Make sure you arereplacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handleit by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.
BULB

1. Open the hood. If you need to change a bulb on
the passenger's side (on the driver's side on 6-cylinder models),
remove the radiator reserve tank.
2. Remove the electrical connector from the bulb by squeezing theconnector to unlock the tab, thenslide the connector off the bulb. 3. Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.
4. Insert the new bulb into the hole and turn it one-quarter turn clock-
wise to lock it in place.
5. Push the electrical connector back onto the bulb. Make sure it is on
all the way.
6. Turn on the headlights to test the new bulb.
7. (Passenger's side on 4-cylinder models, driver's side on 6-cylindermodels)
Reinstall the radiator reserve tank.

Halogen headlight bulbs get very hot when lit. Oil, perspiration, or a scratch
on the glass can cause the bulb to
overheat and shatter.

Maintenance
NOTICE

TAB

Lights

Replacing Front Turn Signal and Side Marker Light Bulbs
HOLDING CLIP
1. If you are changing the bulb on the driver's side, start the engine,
turn the steering wheel all the wayto the right, and turn off the
engine. If you are changing the
bulb on the passenger's side, turn the steering wheel to the left. 2. Use a flat-tipped screwdriver to
remove the holding clip from the
inner fender.
3. Pull the inner fender cover away from the fender and bumper.
4. Remove the socket from the headlight assembly by turning itone-quarter turn counterclockwise. 5. Remove the burned out bulb from
the socket by pushing it in and
turning counterclockwise until it

unlocks.

6. Install the new bulb in the socket. Turn it clockwise to lock it in place.
7. Insert the socket back into the headlight assembly. Turn itclockwise to lock it in place.
8. Test the lights to make sure the new bulb is working.
9. Put the inner fender cover in place. Install the holding clip. Lock it in
place by pushing on the center.

Maintenance

Lights

Replacing a Parking Light Bulb
1. The parking light bulb is under the headlight bulb.
Turn the bulb holder one-quarter turn counterclockwise to remove it
from the lens.
2. Pull the bulb straight out of its
socket.

Push the new bulb straight into
the socket until it bottoms. 3. Put the bulb holder back into its
hole in the lens, and turn it
clockwise until it locks.
4. Turn on the parking lights to make sure the new bulb works.

Maintenance

Lights

Replacing Rear Bulbs (in Fenders)
1. Open the trunk. Remove the fastener from the side
of the trunk lining by turning it
counterclockwise with a coin. Pull
the lining back. 2. Determine which of the two bulbs
is burned out: stop/taillight or turn
signal.

3. Remove the socket by turning it one-quarter turn counterclockwise. 4. Pull the bulb straight out of its

socket.

Push the new bulb straight into
the socket until it bottoms.
5. Reinstall the socket into the light assembly by turning it clockwise
until it locks.
6. Test the lights to make sure the new bulb is working.
7. Reinstall the trunk lining. Make sure it is installed under the edge
of the trunk seal.
8. Put the fastener in the hole on the side of the trunk lining and push
on the center until it locks (the
center is flush with the head).
Maintenance

FASTENER

Lights

Replacing Rear Bulbs

(in Trunk Lid)
1. Open the trunk.
2. Determine which of the two bulbs is burned out: taillight or back-up
light.
3. Remove the socket by turning it
one-quarter turn counterclockwise.
4. Remove the burned out bulb from the socket by pulling it straight outof its socket. 5. Install the new bulb in the socket.
6. Reinstall the socket into the light

assembly.

7. Test the lights to make sure the new bulb is working.
Maintenance

Lights

Replacing a High-mount Brake
Light Bulb
1. Open the trunk and remove the socket from the light assembly by
turning it one-quarter turn counter-
clockwise.

2. Remove the burned-out bulb by pulling it straight out of the socket.
3. Install the new bulb and reinstall the socket. Make sure the new
bulb is working. Replacing a Rear License Bulb
1. Remove the license light assembly by carefully prying on the leftedge of the lens with a flat-tipscrewdriver and pulling the
assembly out. 2. Remove the lens from the bulb
holder by pulling the lens whilesqueezing the tabs on both sides
of the holder.

CONTINUED

Maintenance

BULB