B16a2 HONDA CIVIC 1997 6.G Workshop Manual

HONDA CIVIC 1997 6.G Workshop Manual CIVIC 1997 6.G HONDA HONDA https://www.carmanualsonline.info/img/13/6068/w960_6068-0.png HONDA CIVIC 1997 6.G Workshop Manual

Page 51 of 2189

HONDA CIVIC 1997 6.G Workshop Manual MEASUREMENTSTANDARD INFWIEngine oilCapacityf (uS qt, lmp qt)
Inner-to outer rotor radial clearancePump body-to outer rotor radialclearancePump body to-rotor axial clearance
4.8 (5.1, 4.2) for eng;ne o

Page 99 of 2189

HONDA CIVIC 1997 6.G Workshop Manual 13. Remove the throftle cable by loosening the locknut,
then slip the cable end out of the accelerator link-
age.
NOTE;
. Take care not to bend the cable when removing
it. Always replace any kinked ca

Page 206 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Main Bearings
4.
Glearance
1.To check main bearing-to-journal oil clearance.
remove the main caps and bearing halves.
Clean each main journal and bearing half with a
clean shop towel.
Place one strip

Page 211 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Crankshaft
Inspection
. Clean the crankshaft oil passages with pipe cleaners
or a suitable brush.
. Check the keyway and threads.
Alignment
. Measure runout on all main journals to make
sure the crank

Page 216 of 2189

HONDA CIVIC 1997 6.G Workshop Manual lnspection
1.
Oversize:
Oversize:
NOTE; All replacement piston pins are overslze.
2. Zero the dial indicator to the piston pin diameter
Measure the diameter of the piston pin.
Piston Pin Diametel:
B1

Page 218 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Ring-to-Groove Clearance
After installing a new set of rings, measure ring-to-
groove clearances:
Top Ring Clearance
Standard (New):
B16A2 angine:
0.045 - 0.070 mm (0.0018 - 0.(X128 in)
Dl6Y5, Dt6Y7,

Page 222 of 2189

HONDA CIVIC 1997 6.G Workshop Manual 81642 ongin€:
D16Y5, Dl6fr, Dl6Y8 engines:
k9l.m,
RIGHT SIDE
DOWEL PINS
6 x 1.0 mm11 N.m {1.1a rbf.ft)
OOWEL PIN
9. Apply liquid gasket to the oil pump mating surtace
of the block, then install the

Page 227 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Engine Lubrication
SpecialTools .......... ".""".82
lllustrated Index ........... ... 8-3
Engine Oil
Inspection ...........".....". 8-6
Replacement.............."....."...."......" 8-7
OilFil

Page 249 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Exhaust Manifold
Replacement (contdl
NOTE: Use new gaskets and self-locking nuts when reassembljng.
CAUTION:
. Check for folds or scratches on the surface ot the gask€t.
. R€place with a new gask

Page 269 of 2189

HONDA CIVIC 1997 6.G Workshop Manual Water Pump
Inspection
t.
2.
Remove the timing belt (see section 6).
Turn the water pump pulley counterclockwise.Check that it tarns freely.
Check for signs of seal leakage.
NOTE: A small amount of "w
Page:   1-10 11-20 next >