crankshaft pulley HONDA CIVIC 1998 6.G Workshop Manual

HONDA CIVIC 1998 6.G Workshop Manual CIVIC 1998 6.G HONDA HONDA https://www.carmanualsonline.info/img/13/6068/w960_6068-0.png HONDA CIVIC 1998 6.G Workshop Manual

Page 112 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Cylinder Head/Valve Train
Dl6Y5, D16Y7, Dl6Y8 engines
Special Tools ............. G2
VTEC Control System
Troubleshooting Flowchart .........." 6-3
VTEG Solenoid Valve
Inspection ............" 6-6
VTEC

Page 123 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Valve Clearance
Adjustment
NOTE:
. Valves should be adjusted only when the cylindsrhead temperature is less than 100"F (38"C).
. After adjusting, retorque the crankshaft pulley bolt(see page 6-16).
1,

Page 127 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Crankshaft Pulley and Pulley Bolt
Replacement
When installing and tightening the pulley. follow theprocedure below,
Clean, remove any oil, and lubricate points shown
below.
O: Clean
x: Bemove any oil

Page 128 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Timing Belt
Illustrated lndex
NOTE:
. Refer to page 6-20 for how to position the crankshaft and pulley before installing the belt.
. Mark the direction of rotation on the belt before removing.
a Do no

Page 129 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Timing Belt
Inspection
1.
2.
3.
Remove the cylinder head cover.
. Refer to page 6 46 when installing.
Remove the upper cover (see page 6 19).
Inspect the timing belt for cracks and oil or coolantsoakr

Page 130 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Removal
NOTE:
. Replace the timing belt at 105,000 miles (168.000 km)
according to the maintenance schedule (normal con-
ditions/severe conditions).
lf the vehicle is regularly driven in one or more o

Page 132 of 2189

HONDA CIVIC 1998 6.G Workshop Manual 3. Install the timing belt tightly in the sequence shown
OTiming belt drive pullev (crankshaft) )@Adjusting
pulley -towater pump pulley J@Camshatt pulley
NOTE: Make sure the timing belt drive pulley

Page 133 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Crankshaft Speed Fluctuation (CKF) Sensor
2.
3.
5.
Replacement
4.
1.
6x1.0mm12 N.m {1.2 kgt.m,8.7 tbf.ft)
6. Installthe CKF sensor in reverse order of removal.
Remove the cylinder head cover.
NOTE: R

Page 138 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Removal
Engine removal is not required for this procedure
!!!s@ Make sure iacks and salety stands are
f ta"eata"ea propetty and hoist brackets are attached to the
correct positions on the engine.
CAUT

Page 156 of 2189

HONDA CIVIC 1998 6.G Workshop Manual Cylinder Head
4. Apply liquid gasket (Part No. 08718 - 0001 or 08718 -
0003) to the head mating surfaces of the No. 1 and
No.5 camshaft holders.- Apply liquid gasket to the shaded areas
Set the rocker
Page:   1-10 11-20 21-30 31-40 40 next >