airbag off HONDA CIVIC 2003 7.G Service Manual
[x] Cancel search | Manufacturer: HONDA, Model Year: 2003, Model line: CIVIC, Model: HONDA CIVIC 2003 7.GPages: 1139, PDF Size: 28.19 MB
Page 1086 of 1139
)
t
DTC 9-7: Faulty Right Front lmpact Sensor
Special Tools Bequired. SRS inflator simulator 07SAZ-TB4011A. SRS simulator lead H 07YM-S3AA100
1. Erase the DTC memory {see page 23-26).
2. Turn lhe ignition switch ON {ll), and checkthatthe
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES-Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26).
3. Turn the ignition switch OFF. Check the
connections between SRS unit connectorA (18P)
and the SRS unit, between the engine
compartment wire harness 2P connector and the
right front impact sensor (see page 23-13), and at
connector C401.
Are the connections OK?
YES-Go to step 4.
NO Repair the poor connections and retest. lf DTC
9-7 is still present, go to step 4.
Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the driver's airbag 4P connector from
the cable reel {see step 2 on page 23-21).
Disconnect the front passenger's airbag 4P
connector from the dashboard wire harness (see
step 3 on page 23-21).
Disconnect both seat belt tensioner 2P connectors
from the floor wire harness (see step 5 on page 23-
22).
4.
5.
7.
I
'10.
Disconnect the engine compartment wire harness
2P connector (A) from the right front impact sensor.
Disconnect SRS unit connector A (18P) from the
SRS unit (see step 7 on page 23-221.
Check resistance between the No. 1 and No. 12
terminals of SRS unit connector A (18P). There
should be an open circuit, or at least 1 M 0.
SRS UNIT CONNECTOR A (18PI
GRN
11.
Wire side ol female terminals
ls the resistance as specified?
YES Go to step 11.
NO-Short in the engine companment wire
harness or dashboard wire harness B; replace the
faulty harness,I
Reconnect the battery negative cable.
Turn the ignition switch ON (ll).
(cont'd)
IF!-t1t2)l
Irolrlr
56I6
13161718
SLK
23-79
Page 1088 of 1139
I
)J
DTC 11-1: Open or Increased Resistance in
Driver's Side Airbag Inflator
SpecialTools Required. SRS inflator simulator 07SM-TB4011A. SRS simulator lead E 07XM-S140200
1. Erase the DTC memory (see page 23-26),
2. Tu rn the ignition switch ON (ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SBS indicatot stay on?
YES Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-261.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the driver's side airbag.
07sAz-T84011A
5. Connect the SRS inflator simulator (2 Q connector)
and simulator lead E to the floor wire harness.
I
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
ls DTC 11-1 indicated?
YES Go to step 9.
NO-Open or increased resistance in the driver's
side airbag inflator; replace the driver's side
airbag (see page 23-1'15).1
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger's side airbag 2P
connector (see step 4 on page 23-21) and both seat
belt buckle tensioner 4P connectors (see step 6 on
page 23-221.
{cont'd)
23-81
Page 1089 of 1139
sRs
'I t.
12
DTC Troubleshooting (cont'dl
Disconnect SRS unit connector B (18P)from the
SRS unit (see step 7 on page 23-22). Do not
disconnect the special tool from the floor wire
harness 2P connector.
Check resistance between the No.6 and No. 17
terminals of SRS unit connector B (18P). There
should be 2.0 -3.0 Q.
SRS UNIT CONNECTOR B I18PI
WHT/BLU
rr--r-{lTlslsl a
IdFFI \
120
10tl15
WHT/BLK
Wire side of female terminals
ls the resistance as specified?
YES-Faulty SRS unit or poor contact at SRS unit
connector B (18P) and the SRS unit. Check the
connection; if the connection is OK, replace the
SRS unit (see page 23'1221.a
NO Open or increased resistance in the floor wire
harness; replace the floor wire harness.l
23-82
DTC 11-3: Short to Another Wire or
Decreased Resistance in Driver's Side Airbag
lnflator
SpecialTools Required' SRS inflator simulator 07SAZ-T84011A. SRS simulator lead E o7XAZ-S140200
1. Erase the DTC memory (see page 23 26).
2. Turn the ignition switch ON (ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicatot stay on?
YES Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26).
Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the floor wire harness 2P connector (A)
from the driver's side airbag.
07sAz-T84011A
Connect the SRS inflator simulator (2 0 connector)
and simulator lead E to the floor wire harness.
Reconnect the battery negative cable.
Erase the DTC memory.1.
Page 1090 of 1139
I
I
8. Read the DTC.
ls DTC 11-3 indicated?
YES-Go to step 9.
NO*Shon to another wire in the driver's side
airbag inflator; replace the driver's side airbag (see
page 23-115).I
9. Turn the ignition switch OFF. Disconnect the
battery negative cable. and wait for 3 minutes.
10. Disconnectthe front passenger's side airbag 2P
connector (see step 4 on page 23-21) and both seat
belt buckle tensioner 4P connectors (see step 6 on
page 23-22l,.
11. Disconnect the special tool from the floor wire
harness 2P connector.
12. Disconnect SRS unit connector B {18P)from the
SRS unit {see step 7 on page 23-221.
13. Check resistance between the No.6 and No. 17
terminals of SRS unit connector B (18P), There
should be an open circuit, or at least 1 M 0.
SRS UNIT CONNECTOR B {18PI
Wire side of female terminals
ls the resistance as specified?
YES Faulty SRS unit; replace the SRS unit {seepage 23-'t221 .a
NO Shon to another wire in the floor wire
harness; replace the floor wire ha rness.I
WHT/BLU
WHT/BLK
DTG 11-4: Short to Power in Driver's Side
Airbag Inflator
Special Tools Required. SRS inflator simulator 07SAZ-T84011A. SRS simulator lead E o7XAZ-S140200
1. Erase the DTC memory {see page 23-261.
2. Turn the ignition switch ON (ll), and check thatthe
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SBS indicator stay on?
YES Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26l,.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the driver's side airbag.
07sAz-TB4011A
5. Connect the SRS inflator simulator (2 0 connector)
and simulator lead E to the floor wire harness.
(cont'd)
23-83
Page 1091 of 1139
sRs
DTC Troubleshooting (cont'd)
6. Reconnect the battery negative cable.
7. Erase the DTC memory,
8. Read the DTC.
Is DTC 11-4 indicated?
YES-Go to step 9.
NO Short to power in the driver's side airbag
inflator; replace the driver's side airbag (see page
23-115).t
Turn the ignition swilch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the front passenger's side airbag 2P
connector (see step 4 on page 23-21) and both seat
belt buckle tensioner 4P connectors (see steD 6 on
page 23-221.
9.
'10.
23-84
\.J
11.Disconnect SRS unit connector B (18P) from the
SRS unit (see step 7 on page 23-22l,.
Turn the ignltion switch ON (ll).
Check for voltage between the No. 6 terminal of
SRS unit connector B (18P) and body ground, and
between the No. 17 terminal and body ground.
There should be 0.5 V or less.
SRS UNIT CONNECTOR B I18P)
WHT/BLK
ls the voltage as specitied?
YES- Faulty SRS uniU replace the SRS unit (see
page 23-1221.a
NO Short to power in the floor wire harness;
replace the floor wire harness.l
't2.
13.
UJ
Page 1092 of 1139
I
I
DTC 11-5: Short to Ground in Driver's Side
Airbag Inflator
Special Tools Required. SRS inflator simulator 07SM-T84011A' SRS simulator lead E o7XAZ-S140200
'1. Erase the DTC memory {see page 23-26).
2. Turn the ignition switch ON {ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES Go to step 3.
NO Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-261.
3. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the driver's side airbag.
07saz-TB,r011A
Connect the SRS inflator simulator (2 Q connector)
and simulator lead E to the floor wire harness.
Reconnect the battery negative cable.
Erase the DTC memory.
6.
7.
I
8. Read the DTC.
ls DTC 11-5 ind icated?
YES Go to step 9.
NO Short to ground in the driver's side airbag
inflator; replace the driver's side airbag (see page
23-115).t
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the front passenger's side airbag 2P
connector (see step 4 on page 23-21)and both seat
belt buckle tensioner 4P connectors (see step 6 onpage 23-221.
11. DisconnectSRS unitconnectorB (18P)fromthe
SRS unit (see step 7 on page 23-22).
'12. Check resistance between the No. 17 and No. 15
terminals of SRS unit connector B (18P). and
between the No. '17 and No. 16 terminals. Then
check resistance between the No. 17 terminal and
body ground. There should be an open circuit, or at
least 1 M 0.
SRS UNIT CONNECTOR B I18P)
WHT/BLK
Wire side of female terminals
ls the resistance as specified?
YES Faulty SRS unit; replace the SRS unit (see
page 23-122).a
NO-Short to ground in the floor wire harness;
replace the floor wire harness.I
23-85
Page 1093 of 1139
sRs
DTC Troubleshooting (cont'd)
DTG 12-1: Open or Increased Resistance in
Front Passenger's Side Airbag Inflator
SpecialTools Required. SRS inflator simulator 07SAZ-T84011A. SRS simulator lead E o7XAZ-S140200
1. Erase the DTC memory (see page 23-26).
2. Turn the ignition switch ON (ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SBS indicator stay on?
YES Go to step 3.
NO - Intermittent failu re, system is OK at this time.
Go to Troubleshooting lntermittent Failures (see
page 23-26).
3. Turn the ignition switch OFF. Disconnectthe
battery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the front passenger's side airbag.
07xAz-s1A0200
5. Connect the SRS inflator simulator (2 Q connector)
and simulator lead E to the floor wire harness.
23-86
IJ
7.
'1 0.
9.
Reconnect the battery negative cable.
Erase the DTC memory.
Read the DTC.
ls DTC 12-l indicated?
YES Go to step L
NO-Open or increased resistance in the front
passenger's side airbag inflator; replace the front
passenger's side airbag (see page 23-1 15).1
Turn the ignition switch OFF. Disconnect the
battery negative cable. and wait for 3 minutes.
Disconnect the driver's side airbag 2P connector
{see step 4 on page 23-21)and both seat belt buckle
tensioner 4P connectors (see step 6 on page 23-22).
Page 1094 of 1139
I
1't .
12.
Disconnect SRS unit connector B ('l8P) from the
SRS unit (see step 7 on page 23-22). Do not
disconnect the special tool from the floor wire
harness 2P connector.
Check resistance between the No.7 and No. 18
terminals ofSRS unitconnector B (18P). There
should be 2.0 3.0 (J.
SRS UNIT CONNECTOR B {18P)
WHT/GRN
Wire side of female terminals
ls the resistance as specified?
YES Faulty SRS unit or poor contact at SRS unit
connector B ( l8P) and the SRS unit. Check the
connection; lf the connection is OK, replace the
SRS unit (see page 23-1221.a
NO Open or increased resistance in the floor wire
harness; replace the floor wire harness.I
I
WHT/RED
DTC 12-3: Short to Another Wire or
Decreased Resistance in Front Passenger's
Side Airbag Inflator
SpecialTools Required. SRS inflator simulator 07SAZ-T84011A. SRS simulator lead E o7XAZ-S140200
1. Erase the DTC memory (see p age 23-261.
2. Tu rn the ignition switch ON (ll), and check that the
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES Go to step 3.
NO - Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures (see
page 23-26).
Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
Disconnect the floor wire harness 2P connector (A)
from the front passenger's side airbag.
4.
07xAz-s1A0200
5. Connect the SRS inflator simulator (2 0 connector)
and simulator lead E to the f loor wire harness.
(cont'd)
23-87
Page 1095 of 1139
sRs
DTC Troubleshooting (cont'dl
6. Reconnect the battery negative cable.
7, Erase the DTC memory.
8. Read the DTC.
ls DTC 12-3 indicated?
YES-Go to step I
NO Short to another wire in the front passenger's
side airbag inflator; replace the front passenger's
side airbag (see page 23-ll5).1
9. Turn the ignition switch OFF. Disconnect the
battery negative cable, and wait for 3 minutes.
10. Disconnect the driver's side airbag 2P connector
(see step 4 on page 23-21) and both seat belt buckle
tensioner 4P connectors (see step 6 on page 23-22).
'!1. Disconnect the specialtoolfrom the floor wire
harness 2P connector.
12. Disconnect SRS unit connector B ('lSPlfrom the
SRS unit {see step 7 on page 23-221.
13. Check resistance between the No.7 and No. 18
terminals of sRS unit connector B (18P). There
should be an open circuit, or at least 1 M 0.
SRS UNIT CONNECTOR B I18P)
WHT/RED
-r-'r-Jl' 8lel n
i['tl,Bl S-T
236
10ll15
WHT/GRN
Wire side of {emale terminals
ls the resistance as specilied?
YES Faulty SRS unit; replace the SRS unit {seepage 23-1221.a
NO Short to anolher wire in the f loor wire
harness; replace the floor wire harness.I
23-88
\.J
DTC 12-4: Short to Power in Front Passenger's
Side Airbag Inf lator
Special Tools Required. sRS inflator simulator 07sAz-TB4011A. SRS simulator lead E 07XM-S140200
1. Erase the DTC memory (see page 23-26).
2. Turn the ignition switch ON (ll), and check thatthe
SRS indicator comes on for about 6 seconds and
then goes off.
Does the SRS indicator stay on?
YES-Go to step 3.
NO- Intermittent failure, system is OK at this time.
Go to Troubleshooting Intermittent Failures {see
page 23-26).
3. Turn the ignition switch OFF. Disconnect the
banery negative cable, and wait for 3 minutes.
4. Disconnect the floor wire harness 2P connector (A)
from the front passenger's side airbag.
07xAz-s1A0200
5. Connect the SRS inflator simulator (2 Q connector)
and simu lator lead E to the floor wire harness.
Page 1096 of 1139
\
6. Reconnect the battery negative cable.
7. Erase the DTC memory.
8. Read the DTC.
ls DTC 12-4 indicated ?
YES Go to step 9.
NO-Short to power in the front passenger's side
airbag inflator; replace the front passenger's side
airbag (see page 23-115). t
9. Turn the ignition swilch OFF. Disconnectthe
battery negative cable, and wait for 3 minutes.
'10. Disconnect the driver's side airbag 2P connector(see step 4 on page 23-21) and both seat belt buckle
tensioner 4P connectors (see step 6 on page 23-22l,.
t
11.Disconnect SRS unit connector B (18P) from the
SRS unit (see step 7 on page 23-221.
Turn the ignition switch ON (ll).
Check for voltage between the No. 7 terminal of
SRS unit connector B ( l8P) and body ground, and
between the No. 18 terminal and body ground.
There should be 0.5 V or less.
SRS UNIT CONNECTOR B I18P)
WHT/GRN
ls the voltage as specified?
YES Faulty SRS unil; replace the SRS unit (see
page 23-1221 .a
NO Short to power in the floor wire harness;
replace the floor wire harness.l
1?
13.
23-89