brake light HONDA CIVIC HATCHBACK 2002 7.G Owners Manual

If the indicator remains lit after
you have f ully released the
parking brake while the engine is
running, or if it comes on while
driving, it can indicate a problem
in the brake system. For complete
inf ormation, see page .
This indicator comes on when you
turn the ignition switch ON (II). It
is a reminder to check the parking
brake. Driving with the parking
brake not f ully released can
damage the brakes and tires.
This light has two f unctions:
This indicator lights when you turn
the ignition switch ON (II). If it
comes on at any other time, it
indicates a potential problem with
your f ront airbags. This light will
also alert you to a potential problem
with your side airbags or passenger’s
side airbag automatic cutoff system.
For complete inf ormation, see page
.
This indicator lights when you turn
the ignition switch ON (II). If it
comes on at any other time, it
indicates that the passenger’s side
airbag has automatically shut off.
For complete inf ormation, see page . This light normally comes on f or a
f ew seconds when you turn the
ignition switch ON (II), and when
the ignition switch is turned to
START (III). If this light comes on at
any other time, there is a problem in
theABS.If thishappens,takethe
cartoyourdealertohaveitchecked.
With the light on, your car still has
normal braking ability but no anti-
lock. For complete inf ormation, see
page .
47
1. 2.
48
329 221
Only on models equipped with ABS (see
page )
Only on models equipped with side airbags 220
Indicator L ights
Inst rument s and Cont rols
Supplemental Restraint
System Indicator
Parking Brake and Brake System
Indicator
Side A irbag Cut-of f
IndicatorAnti-lock Brake System (ABS)
Indicator
57
U.S. Canada
U.S. Canada

The lef t or right turn signal light
blinks when you signal a lane change
or turn. If the light does not blink or
blinks rapidly, it usually means one
of the turn signal bulbs is burned out
(see page ). Replace the bulb as
soon as possible, since other drivers
cannot see that you are signalling.
WhenyouturnontheHazard
Warning switch, both turn signal
lights blink. All turn signals on the
outside of the car should f lash.
The appropriate light comes on in
this display if the trunk or any door
is not closed tightly. If a brake light
does not work, the
indicator comes on when you push
the brake pedal with the ignition
switch ON (II).
A burned out brake light is a hazard
when drivers behind you cannot tell
you are braking. Have your brake
lights repaired right away.
All the lights in the monitor display
come on f or a f ew seconds when you
turn the ignition switch ON (II).
This indicator has three f unctions:
Itcomesonasareminderthatyou
have turned off the Traction
Control System.
It f lashes when the TCS is
regulating wheelspin.
If itcomesonandstaysonwhen
the Traction Control System is on,
it indicates that there is a problem
in the TCS.
This light also comes on when you
turn the ignition ON (II) and goes off
af ter the engine starts. See page f or more inf ormation on the
TCS.
1. 2. 3.
222 293
On all V6 models
Indicator L ights
Inst rument s and Cont rols
Turn Signal and
Hazard Warning
Indicators
Door and Brake L amp Monitor
Traction Control System
(T CS) Indicator
58
BRAKE LAMP

This indicator comes on f or a f ew
seconds when you turn the ignition
switch ON (II). It will then go of f if
you have inserted a properly-coded
ignition key. If it is not a properly-
coded key, the indicator will blink
and the engine will not start (see
page ).
This indicator also blinks several
times when you turn the ignition
switch f rom ON (II) to ACCESSORY
(I) or LOCK (0).
This light comes on when the
washer f luid level is low. Add washer
f luid when you see this light come on
(see page ).
This indicator lights when you turn
the ignition switch to ON (II) with
the headlight switch of f and the
parking brake set. It should go of f if
youturnontheheadlightsorrelease
the parking brake. If it comes on at
any other time, it means there is a
problem with the DRL. There may
also be a problem with the high
beam headlights.
This light comes on with the high
beam headlights. See page for
inf ormation on the headlight
controls.
On Canadian models, this indicator
comes on with reduced brightness
when the Daytime Running Lights
(DRL) are on (see page ). This lights when you set the cruise
control. See page f or inf ormation
on operating the cruise control.
This light comes on as a reminder
that you must ref uel soon.
64
65 185
71
262
Canadian models only
Only on models equipped with Cruise
Control System
Canadian models only
Indicator L ights
Inst rument s and Cont rols
Immobilizer System
Indicator
Washer Level Indicator
‘‘Daytime Running
Lights’’ Indicator
High Beam Indicator
Cruise Control Indicator
Low Fuel Indicator
59

Resting your f oot on the brake or
clutch pedal will cause the cruise
control to cancel.Tap the brake or clutch pedal
lightly with your f oot. The
CRUISE CONTROL light on the
instrument panel will go out.
When the car slows to the desired
speed, press the SET/decel button.
The car will then maintain the
desired speed.
Even with the cruise control turned
on, you can still use the accelerator
pedal to speed up f or passing. Af ter
completing the pass, take your foot
of f the accelerator pedal. The car
will return to the set cruising speed.
Thecruisecontrolmaynotholdthe
set speed when you are going up and
down hills. If your speed increases
going down a hill, use the brakes to
slow down to the desired speed. This
will cancel the cruise control. To
resume the set speed, press the
RESUME/accel button. The
CRUISE CONTROL light on the
instrument panel comes on.
To slow down in very small
amounts, tap the SET/decel
button repeatedly. Each time you
do this, your car will slow down
about 1 mph (1.6 km/h).
Press and hold the SET/decel
button. The vehicle will decelerate.
Release the button when you
reach the desired speed.
You can decrease the set cruising
speed in any of these ways: To increase your speed in very
small amounts, tap the RESUME/
accel button repeatedly. Each time
you do this, your car will speed up
about 1 mph (1.6 km/h).
Push on the accelerator pedal. Ac-
celerate to the desired cruising
speed and press the SET/decel
button.
Press and hold the RESUME/
accel button. The car will acceler-
ate. When you reach the desired
cruising speed, release the button.
You can increase the set cruising
speed in any of these ways:
When climbing a steep hill, the
automatic transmission may
downshif t to hold the set speed.
Cruise Control
Comf ort and Convenience Feat ures
Changing the Set Speed
186

Pressing the Cruise Control Master
Switch turns the system completely
of f and erases the previous cruising
speed f rom memory. To use the
system again, ref er to.
When you push the CANCEL button,
or tap the brake or clutch pedal, the
CRUISE CONTROL light on the
instrument panel will go out and the
car will begin to slow down. You can
use the accelerator pedal in the
normal way.
The system remembers the
previously-set cruising speed. To
return to that speed, accelerate to
above25mph(40km/h),thenpress
and release the RESUME/accel
button. The CRUISE CONTROL
light comes on, and the car will
accelerate to the same cruising
speed as bef ore.
Press the Cruise Control Master
Switch.
Push the CANCEL button on the
steering wheel.
Tap the brake or clutch pedal.
Youcancancelthecruisecontrolin
any of these ways:
Cruise Control
Using t he
Cruise Cont rol
Cancelling the Cruise Control
Comf ort and Convenience Feat ures187
CCAANNCCEELLBBUUTTTTOONN

Many states and Canadian provinces
require special outside mirrors when
towing a trailer. Even if they don’t,
you should install special mirrors if
you cannot clearly see behind you, or
if the trailer creates a blind spot.
Askyourtrailersalesorrental
agency if any other items are
recommended or required f or your
towing situation.When preparing to tow, and bef ore
driving away, be sure to check the
f ollowing:
Your vehicle tires and spare are
properly inf lated (see page ),
and the trailer tires and spare are
inflated as recommended by the
trailer maker.
The vehicle has been properly
serviced, and the tires, brakes,
suspension, and cooling system
are in good operating condition.
All weights and loads are within
limits (see pages and ).
Thehitch,safetychains,andany
other attachments are secure.
Allitemsonandinthetrailerare
properly secured and cannot shif t
while you drive.
The lights and brakes on your
vehicle and the trailer are working
properly. 227 228
285
Additional Trailer EquipmentPre-T ow Checklist
Towing a Trailer
Driving231

µ
Ì
Î ÎÎ ÌÎÎ
Î
Î
ÌÌ
Follow the Maintenance
Schedule f or Severe Conditions.
Follow the Severe Conditions
Maintenance Schedule if you
drive your vehicle
under one or more of the
f ollowing conditions:
Driving less than 5 miles (8
km) per trip or, in f reezing
temperatures, driving less
than 10 miles (16 km) per trip.
Driving in extremely hot
[over 90°F (32°C)] conditions.
Extensive idling or long
periods of stop-and-go driving.
Trailer towing, driving with a
car top carrier, or driving in
mountainous conditions.
Driving on muddy, dusty, or
de-iced roads.
MAINLY
Maint enance
U.S. Owners
Canadian Owners
242
Visually inspect the following items: Replace every 3,750 miles (6,000 km) or 6 months
Check oil and coolant at each fuel stop
Service at the indicated
distance or time whichever
comes first.
miles x 1,000
km x 1,000
months
Balancer belt applies to 4-cylinder models only.
See timing belt on page to determine need for replacement. See information on maintenance and
emissions warranty, last column, page .
Every 60,000 miles (96,000 km) or 3 years
120,000 miles (192,000 km) or 10 years, then every
60,000 miles (96,000 km) or 5 years
See Dust and Pollen Filter on page for replacement information under special driving conditions.
Replace engine oil and oil filter
Check engine oil and coolant
Clean ( ) or replace ( ) air cleaner element
Use normal schedule except in dusty conditons
Inspect valve clearance
Replace spark plugs
Replace timing belt , balancer belt , and
inspect water pump
Inspect and adjust drive belts
Inspect idle speed
Replace engine coolant
Replace transmission fluid
Inspect front and rear brakes
Replace brake fluid
Check parking brake adjustment
Replace dust and pollen filter
Lubricate all hinges, locks and latches
Rotate tires (Check tire inflation and condition
at least once per month) Every 3 years (independent of mileage)
Tie rod ends, steering gear box, and boots
Suspension components, driveshaft boots
Brake hoses and lines (including ABS)
All fluid levels and conditions of fluids
Cooling system hoses and connections Exhaust system, fuel lines and connections
Lights and controls, vehicle underbody 152412
304824457236609648
75
120
60 90
144 72 105168
84 120192
96
Rotate tires every 7,500 miles (12,000 km)
Every 7,500 miles (12,000 km) or 6 months Adjust only if noisy
Every 7,500 miles (12,000 km) or 6 months
:
1:2:3: 239
283 MTAT
282
60,000 miles (96,000 km) or 3 years, then every 30,000 miles (48,000 km) or 2 years
11 ,2
3
Maintenance Schedule for Severe Conditions

µµ
Ø ØØØØØØØ Ø Ø Ø ØØØØØØØØ
Ø Ø Ø Ø Ø
Ì
Ì Ì
Î
ÌÎÎ Î
Î ÎÎ
CONT INUED
Maint enance243
A, B, C, D, E
U.S. Owners
Canadian Owners
AB C D E
Service at the indicated distance or time, whichever comes first. Do the items in as required for each distance/time.
Refer to page to determine which schedule to use.
Use the Maintenance Schedule for Severe Conditions. Replace engine oil and filter.
Inspect front and rear brakes.
Rotate tires (follow pattern on page ).
Inspect tie rod ends, steering gear box and boots.
Inspect suspension components.
Inspect driveshaft boots.
Check parking brake adjustment.
Lubricate all hinges, locks and latches with
multipurpose grease.
Inspect brake hoses and lines (including ABS)
Check all fluid leves, condition of fluids, and check
for leaks.
Inspect cooling system hoses and connections.Inspect exhaust system.
Inspect fuel lines and connections
Check all lights.
Inspect the underbody.
Replace air cleaner element.
Inspect and adjust drive belts.
Replace dust and pollen filter .
Replace brake fluid every 3 years
(independent of mileage).
Do items in A.
Do items in A, B.
Do items in A.
Clean air cleaner element.
DoitemsinA,B,C.
Do items in A.
Do items in A, B.
Do items in A.
DoitemsinA,B,C,D.
Do items in A.
Do items in A, B.
Do items in A.
Do item in E.
Clean air cleaner element. Do items in A, B, C.
Do items in A.
Do items in A, B.
Do items in A.
Replace MT fluid.
Replace AT fluid.
Replace timing belt , balancer belt , inspect
water pump.
DoitemsinA,B,C,D.
Do items in A.
3,750 mi/6,000 km
7,500 mi/12,000 km
11,250 mi/18,000 km
15,000 mi/24,000 km/1 yr
18,750 mi/30,000 km
22,500 mi/36,000 km
26,250 mi/42,000 km
30,000 mi/48,000 km/2 yrs
33,750 mi/54,000 km
37,500 mi/60,000 km
41,250 mi/66,000 km
3 yrs (independent ofmileage)
45,000 mi/72,000 km/3 yrs
48,750 mi/78,000 km
52,500 mi/84,000 km
56,250 mi/90,000 km
60,000 mi/96,000 km/3 yrs
60,000 mi/96,000 km/3 yrs,
then replace every 30,000 mi/
48,000 km/2 yrs.
60,000 mi/96,000 km/4 yrs
63,750 mi/102,000 km
287
:
242
Check engine oil and coolant at each fuel stop.
Check and adjust valve clearance, cold engine, only if noisy.
See information on maintenance and emissions warranty, last
column, page .
See timing belt on page to determine need for replacement.
Balancer belt applies to 4-cylinder models only.
See Dust and Pollen Filter on page for replacement
information under special driving conditions. NOTE:
283
282 239
1:2:3:
3
11 ,2
Maintenance Schedule for Severe Conditions (listed by distance/time)

Check the f ollowing:Headlights (low and high beam)
Parking lights
Taillights
Brake lights
High-mount brake light
Turn signals
Back-up lights
Hazard light f unction
License plate light
Side marker lights
Daytime running lights
(Canadian models)
If you f ind any bulbs are burned out,
replace them as soon as possible.
Refer to the chart on page to
determine what type of replacement
bulb is needed. 343
Lights
Maint enance291
SSTTOOPP//TTAAIILLLLIIGGHHTTTTUURRNNSSIIGGNNAALLLLIIGGHHTT
HHIIGGHH--MMOOUUNNTTBBRRAAKKEELLIIGGHHTT
TTAAIILLLLIIGGHHTT
BBAACCKK--UUPPLLIIGGHHTT

Open the trunk and remove the
socket f rom the light assembly by
turning it one-quarter turn counter-
clockwise.
Remove the burned-out bulb by
pulling it straight out of the socket.
Install the new bulb and reinstall
the socket. Make sure the new
bulb is working.Remove the license light assembly
by caref ully prying on the lef t
edge of the lens with a f lat-tip
screwdriver and pulling the
assembly out.
Remove the lens f rom the bulb
holder by pulling the lens while
squeezing the tabs on both sides
of the holder.
1.
2. 3. 1.
2.
CONT INUED
Replacing a High-mount Brake
Light BulbReplacing a Rear License PlateBulb
Lights
Maint enance297
BBUULLBB