S mode HONDA INSIGHT 2010 2.G Owner's Guide

ÛÝ
ÛÝ
Adjust Outside Temp. Display
If you sometimes f ind that the
temperature reading is a f ew
degrees above or below the actual
temperature, you can adjust it by
f ollowing these instructions: Adjust the outside temperature value
by pressing the INFO ( / ) button
repeatedly. Press the SEL/RESET
button to set the desired value.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘ADJUST OUTSIDE TEMP.
DISPLAY’’ and repeat the procedure
again.
You can choose this item to
customize f rom ‘‘METER SETUP’’
by pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the setting.
Multi-Inf ormation Display
98
Canadian models
Canadian models
U.S. models
U.S. models
—
—y


y
)"y
y
2010 Insight

Û
Ý
ÛÝ
Ý
Û
There is one custom setting f or the
lighting setup:
INTERIOR LIGHT
DIMMING TIME
While ‘‘LIGHTING SETUP’’ is
shown, press the SEL/RESET
button to enter the customize mode.
Each time you press the INFO ( /) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. Lighting Setup
Multi-Inf ormation Display
104
: Press the SEL/RESET button.
: Press the INFO button .
: Press the INFO button . See page
105
—
—y

y
)"y
y
2010 Insight

Û
Ý
ÛÝ
ÛÝ
AUTO DOOR LOCK
Here are the five custom settings for
the door setup:
While ‘‘DOOR SETUP’’ is shown,
press the SEL/RESET button to
enter the customize mode.
Each time you press the INFO ( /
) button, the screen changes as
shown in the illustration. Press the
INFO ( / ) button until you see
the setting you want to customize,
then press the SEL/RESET button
to enter your selection. KEYLESS LOCK
ACKNOWLEDGMENT
SECURITY RELOCK TIMER AUTO DOOR UNLOCK
DOOR LOCK MODE
Door Setup
Multi-Inf ormation Display
106
: Press the INFO button .
: Press the INFO button .
: Press the SEL/RESET button. See page
107
See page
108
See page
113 See page
112See page
110
—
—y

y
)"y


y
2010 Insight

µÛÝ
ÛÝ
µ
µ
Auto Door Lock
There are three settings you can
choose f rom:
SHIFT FROM P
The doors lock whenever you move
the shift lever out of Park.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
Press the SEL/RESET button to
enter the selecting mode.
WITH VEHICLE SPEED
The doors lock when the vehicle
speed reaches about 10 mph (about
16 km/h).
OFF
The auto door lock mode is
deactivated all the time.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
107
A/T model is shown.
—
—y

y
)"y

y
2010 Insight

µ
µ
ÛÝ ÛÝ
µ
DRIVER DOOR WITH IGN OFF
The driver’s door unlocks when you
turn the ignition switch to the LOCK
(0) position.
ALL DOORS WITH IGN OFF All
the doors unlock when you turn the
ignition switch to the LOCK (0)
position.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button.
For example, you choose ‘‘DRIVER
DOOR with SHIFT to P,’’ you will
seetheabovedisplay.
OFF The auto door unlock is
deactivated all the time.
CONT INUED
Multi-Inf ormation Display
Inst rument s and Cont rols
109
—
—y


y
)"y

y
2010 Insight

ÛÝ
Press the SEL/RESET button to
enter your selection. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘AUTO
DOOR UNLOCK’’ and repeat the
procedure again.To select whether the driver’s door
unlocks or all the doors unlock when
you unlock the doors with the
remote transmitter or the key, follow
these instructions.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
If you choose ‘‘ALL DOORS With
IGN OFF,’’ you will see the above
display.
Door Lock Mode
Multi-Inf ormation Display
110
—
—y



y
)"y

y
2010 Insight

ÛÝ
Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button. When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.If the ‘‘SETTING INCOMPLETE’’
message appears, go back to ‘‘DOOR
LOCK MODE’’ and repeat the
procedure again.
Multi-Inf ormation Display
Inst rument s and Cont rols
111
—
—y



y
)"y

y
2010 Insight

ÛÝ
ÛÝ Press the SEL/RESET button to
enter the selecting mode.
Select ON or OFF by pressing the
INFO ( / ) button, then enter
your selection by pressing the SEL/
RESET button.
You can choose this item to
customize f rom ‘‘DOOR SETUP’’ by
pressing the INFO ( / ) button
repeatedly.
When you push the LOCK button on
the remote transmitter, some
exterior lights f lash, and a beeper
sounds when you push the LOCK
button again within 5 seconds to
verify that the doors and the trunk
arelockedandthesecuritysystem
has set (see page ). You can
customize the exterior lights not to
f lash and the beeper not to sound.
255
Keyless Lock Acknowledgment
Multi-Inf ormation Display
112
—
—y


y
)"y

y
2010 Insight

ÛÝIf the ‘‘SETTING INCOMPLETE’’
message appears, go back to
‘‘SECURITY RELOCK TIMER’’ and
repeat the procedure again.
When your selection is successf ully
completed, the display changes as
shown above, and then goes back to
the customize item screen.
Press the SEL/RESET button to
enter the selecting mode.
Select the desired setting by
pressing the INFO ( / ) button,
then enter your selection by pressing
the SEL/RESET button.
Multi-Inf ormation Display
114
—
—y


y
)"y

y
2010 Insight

ÛÝÛÝ
If you want to set the def ault settings,
press the INFO ( / ) button to
select DEFAULT ALL, then press
the SEL/RESET button.
If the setting is not successfully
completed, ‘‘FAILED’’ is shown f or
several seconds, and then the screen
goes back to the normal message
mode. Repeat the same procedure to
select DEFAULT ALL.
If you want to cancel DEFAULT
ALL, select CANCEL, then press the
SEL/RESET button. The screen
goes back to the previous display. To set the def ault settings, press the
INFO ( / ) button to select SET
then press the SEL/RESET button.
When DEFAULT ALL is set, you will
see the above display for several
seconds, then the screen returns to
the default all setting display.
DEFAUL T AL L
Multi-Inf ormation Display
Inst rument s and Cont rols
115
—
—y


y
)"y
y
2010 Insight