Clock HONDA ODYSSEY 2011 RB3-RB4 / 4.G User Guide

To set the time, press and release
the CLOCK button. The display
will change to the clock adjust
screen.
You can also set the time from the
setup menu.
Change the hours by pressing the H
(hour) button until the numbers
advance to the desired time. Change
the minutes by pressing the M
(minute) button until the numbers
advance to the desired time.
Press the CLOCK button again to
enter the set time.
Press the SETUP button to display
the setup menu. Turn the selector
knob to ‘‘CLOCK ADJUST’’ and
press the selector knob.
To set the time, press the CLOCK
button until you hear a beep. The
displayed time begins to blink. If your vehicle’s battery is
disconnected or goes dead, you may
need to set the clock.
1.
CONT INUED
On LX models EX, EX-L models
Setting the Clock
On Vehicles wit hout Navigat ion
Syst em
Features
315
CLOCK
BUTTON
HOUR
BUTTON Without rear
entertainment
system
With rear
entertainment
system
MINUTE BUTTON
CLOCK BUTTON CLOCK BUTTON
10/07/17 10:16:19 31TK8600_320
2011 Odyssey

Ú
On vehicles with navigation systemThe navigation system receives
signals f rom the global positioning
system (GPS), and the displayed
time is updated automatically by the
GPS. Ref er to the navigation system
manual f or how to adjust the time.
Turn the selector knob to change
the setting between 12H and 24H,
and count the numbers up or down.
To enter the clock setting, press
the selector knob repeatedly to
select ‘‘SET’’ or ‘‘EXIT,’’ then press
the knob. The display will return
to the setup menu.
Press the selector knob to select
the item which you want to adjust.
Each time you press the selector
knob, the selected item changes
between hours, minutes, SET and
EXIT. The selected item is
indicated with in the display.
2. 3.
4.
Setting the Clock316U.S. EX models
EX-L and Canadian EX models
10/07/17 10:16:26 31TK8600_321
2011 Odyssey

When the radiator and engine are
cool, relieve any pressure in the
cooling system by turning the
radiator cap counterclockwise,
without pressing down.
Remove the radiator cap by
pushing down and turning
counterclockwise.The coolant level should be up to
the base of the f iller neck. Add
coolant if it is low.Pour coolant into the reserve tank.
Fill it to half way between the MAX
and MIN marks. Put the cap back
on the reserve tank.
Do not add any rust inhibitors or
other additives to your vehicle’s
cooling system. They may not be
compatible with the coolant or
engine components. Put the radiator cap back on, and
tighten it fully.
Pourthecoolantslowlyand
caref ully so you do not spill. Clean
up any spill immediately; it could
damage components in the engine
compartment.
3. 4.
5.
1.
2.
Engine Coolant
Maint enance
619
Fill up to here
RADIATOR CAP FILLER NECK
10/07/17 10:57:00 31TK8600_624
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise. Reinstall the air intake duct
securely.
Reinstall the engine coolant
reserve tank and power steering
reservoir. Open the hood.
Remove the electrical connector
f rom the bulb by pushing on the
tab and pulling the connector
down.
Remove the bulb by turning it
about one-quarter turn
counterclockwise.
4. 5.
6.
3. 7.
8.
2.
3. 1.
CONT INUED
Driver’s sidePassenger’s side
Lights
L ow Beam Headlight s
Maint enance
627
TAB
CONNECTOR BULB
BULBTAB
CONNECTOR
10/07/17 10:58:08 31TK8600_632
2011 Odyssey

Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector onto
the new bulb.
Turn on the headlights to test the
new bulb.Open the hood.
Remove the socket from the
headlight assembly by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket.Turn on the lights to make sure
the new bulb is working. Insert the socket back into the
headlight assembly. Turn it
clockwise to lock it in place. Push the new bulb straight into
the socket until it bottoms.
1.
4.
5.
6.
2.
3. 4.
5.
6.
Lights
Replacing the Front Side Marker/
Parking/Turn Signal Light Bulb
628
BULB
SOCKET
10/07/17 10:58:18 31TK8600_633
2011 Odyssey

Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the bulb by turning it
approximately one-quarter turn
counterclockwise.Insert the new bulb into the hole,
and turn it one-quarter turn
clockwise to lock it in place.
Push the electrical connector back
onto the bulb. Make sure it is on
all the way.
Reinstall the inner f ender. Make
sure it is installed under the edge
of the f ront bumper.
Reinstall the screws and mounting
bolt on the inner f ender cover, and
tighten them securely. Turn on the f og lights to test the
new bulb.
Open the tailgate.
Use a Phillips-head screwdriver to
remove the two mounting bolts.
3.
4. 5.
7. 6.
8.
9.
1.
Lights
Replacing Rear Bulbs
(in Rear Pillar)
630
BULB
TAB CONNECTOR Pull up
Slide
MOUNTING BOLTS
10/07/17 10:58:35 31TK8600_635
2011 Odyssey

CONT INUED
Remove the socket f or that bulb
by turning it one-quarter turn
counterclockwise. Determine which of the two bulbs
is burned out: stop/taillight or turn
signal light.
Rotate the assembly toward the
side panel until it slightly overlaps
the bumper and the bottom of the
taillight housing is exposed.
With the hand closest to the cargo
area, use your f ingers to grip the
bottom edge of the assembly.
Apply a rearward and upward
pulling motion to release the lower
f astener f rom the grommet.
Continue to support the assembly
while placing the f ingers of the
outer hand on the top of the outer
corner of the assembly.
Pull with the upper f inger and
hand to release the upper f astener
f rom the top grommet.
2.
3.
4.
5.
6.7.
8.
Lights
Maint enance
631
BULB
SNAP FASTENERS
SOCKET
10/07/17 10:58:44 31TK8600_636
2011 Odyssey

Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Reinstall the socket into the light
assembly by turning it one-quarter
clockwise until it locks.
Turn on the lights to make sure
the new bulb is working.
Ensure that the grommets are still
in place on the body panel.Open the tailgate. Place a cloth on
the edge of the cover to prevent
scratches. Remove it by caref ully
prying in the notch on its edge
with a small f lat-tip screwdriver.
Determine which of the two bulbs
is burned out: taillight or back-up
light.
Insert the fasteners into the
grommets and push the assembly
back into place. You will hear the
f asteners engage.
Install the mounting bolts and
tighten securely.
1.
2.
9.
11. 10.
12. 14. 13.
Lights
Replacing Rear Bulbs
(in Tailgate)
632
COVER
GROMMET
FASTENER
If the grommets are loose or completely
out of the holes af ter the taillight
assembly is removed, they must be
replaced. Ask your dealer f or more
inf ormation.
10/07/17 10:58:53 31TK8600_637
2011 Odyssey

Remove the socket by turning it
one-quarter turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Reinstall the base gasket.
Push the electrical connector back
onto the socket. Make sure it is on
all the way.
Turn on the lights to make sure
the new bulb is working.
Reinstall the cover.
Remove the electrical connector
f rom the bulb by pushing on the
tab to unlock it, then slide the
connector of f the bulb.
Remove the base gasket as shown,
then remove the socket by turning
it one-quarter turn
counterclockwise. 4.
5.
6.
9.
3.
8. 7. (Taillight)
10.
(Back-up light)
3.
4.
Lights
Maint enance
633
BULB
SOCKET
CONNECTOR
BULB TAB
SOCKET
BASE GASKET
10/07/17 10:59:04 31TK8600_638
2011 Odyssey

Remove the socket f rom the light
assembly by turning it one-quarter
turn counterclockwise.
Pull the bulb straight out of its
socket. Push the new bulb straight
into the socket until it bottoms.
Place a cloth on the edge of the
lens segment to prevent scratches.
Remove each lens segment by
caref ully prying on its edge with a
small f lat-tip screwdriver.
Remove the screws with a Phillips-
head screwdriver, then remove
the light assembly f rom the
tailgate.
Insert the socket back into the
light assembly. Turn it clockwise
to lock it in place.
Turn on the lights to make sure
the new bulb is working.
Reinstall the cover.
1.
2. 3.
4.
5.
6.
7.
Lights
Replacing a High-mount Brake
Light Bulb
634
SCREWS
LENS SEGMENTS
SOCKETBULB
10/07/17 10:59:13 31TK8600_639
2011 Odyssey