mirror Hyundai Accent 2006 Owner's Guide

3
1
CONTROLS AND EQUIPMENT
ZB010C1-E "Alternative fuels" Fuels which contain methanol or etha- nol must not be used. ZB010D1-E Operation in Foreign Countries Drivers of vehicles which are to be operated in foreign countries must sat-isfy themselves that:
o The vehicle meets all local regula-
tions with respect to insurance, speci- fications etc..
o The correct types and grades of fuel are available for satisfactory opera-tion of the vehicle.
BEFORE ENTERING THE VEHICLE
YB020A1-E
o Ensure that all windows, mirrors and
lamps are clean.
o Check condition of all tyres.
o Ensure that no fluid leaks are evi- dent.
o Ensure that the area around the ve-
hicle is clear before driving off.
SB010E1-E FUELS FOR CLEANER AIR To help contribute to cleaner air, Hyundai recommends that you use fuels treatedwith detergent additives, which help to prevent deposit formation in the engine. These fuels will help the engines runcleaner and the Emission Control Sys- tem performance.

1CONTROLS AND EQUIPMENT
4RUNNING IN YOUR NEW HYUNDAI
B020A01FC-EAT (Petrol Engine) The longevity and performance of the vehicle are greatly affected by the careexercised during the first 1,000 miles of motoring. Because of modern manu- facturing techniques, rigid guidelinesregarding maximum road speeds have become unnecessary. However, cer- tain precautions should be observed inorder to obtain the best possible perfor- mance and useful life from the vehicle.
1) Do not race the engine without a load
(i.e revving the engine in neutral).
2) During the first 500 miles the maxi- mum engine speed should be re- stricted to 3,000 rpm and gradually increased thereafter.
3) Avoid prolonged constant speed op- eration. The internal components ofthe engine will become runin morequickly if the operation speed is var- ied during the running-in period.
4) Never allow the engine to labour. Use the gearbox freely and avoid largethrottle openings when the engine speed is below 1,500 rpm. 5) Avoid rapid acceleration and maxi-
mum throttle openings.
6) Avoid harsh braking during the first 100 miles of urban motoring or 1,000miles of motorway driving to allowthe friction facings of the brake pads and shoes to bed against the discs and drums properly.
7) No trailer towing should be under- taken during the running-in period.
B020B01FC-EAT (Diesel Engine) The longevity and performance of the vehicle are greatly affected by the care exercised during the first 1,000 miles of motoring. Because of modern manu-facturing techniques, rigid guidelines regarding maximum road speeds have become unnecessary. However, cer-tain precautions should be observed in order to obtain the best possible perfor- mance and useful life from the vehicle.AFTER ENTERING THE VEHICLE
YB020B1-E
o Ensure that all occupants fasten and
correctly adjust seat belts.
o Ensure that seat and headrestraint
positions are adjusted for optimum safety, control and comfort.
o Adjust interior and exterior rear view
mirrors.
o Verify correct operation of lamps,
horn and other electrical equipment.
o Ensure that warning lamps illumi- nate when ignition is turned on.
NOTE: Fluid levels such as engine oil, en- gine coolant, brake and windscreen washer fluid should be checked daily or at each refuelling, whichever oc-curs sooner.

1CONTROLS AND EQUIPMENT
64
To adjust the position of either mirror:
1. Move the selecting switch to the "L"
(or "R") position to activate the ad- justable mechanism for the adjust- ing door mirror.
2. Now, adjust mirror angle by depress-
ing the appropriate perimeter switchas illustrated.
B510B01A
MIRRORSEAT POCKET B510B01FC-EAT OUTSIDE REARVIEW MIRROR Electric Type The outside rearview mirrors can be adjusted in any direction to give the maximum rearview vision.The remote control outside rearview mirror switch controls the adjustments for passenger side door mirror.HLC2114-D
A seat side pocket is located on thefront passenger seat to hold papers.There are seatback pockets on the backside of the front seats. HLC2119-D
B540B01TB-EAT (Not all models)

65
1
CONTROLS AND EQUIPMENT
B510C01A-EAT OUTSIDE REARVIEW MIRROR HEATER (Not all models) The outside rearview mirror heater is actuated in connection with the rear window defroster. To heat the outsiderearview mirror glass, push in the switch for the rear window defroster. The rear- view mirror glass will be heated fordefrosting or defogging and will give you improved rear vision in inclement weather conditions. Push the switchagain to turn the heater off. The outside rearview mirror heater automatically turns itself off after 20 minutes.
CAUTION:
o Do not leave the switch on for an unnecessary length of time.
o Scraping ice from the mirror face could cause permanent damage.To remove any ice, use a sponge,soft cloth or approved deicer.
o Be careful when judging the size
or distance of any object seen inthe passenger side rear view mir- ror. It is a convex mirror with a curved surface, any objects seenin this mirror are closer than they appear.
!
B370A01A-D
!
B510C01A-EAT FOLDING THE OUTSIDE REAR- VIEW MIRRORS To fold the outside rearview mirrors, push them towards the rear. The outside rearview mirrors can befolded rearward for parking in restricted areas.WARNING:
Do not adjust or fold the outside rearview mirrors whilst the vehicle ismoving. This could result in loss of control, and an accident causing death, serious injury or propertydamage. HLC2115-D

1CONTROLS AND EQUIPMENT
66HIGH-MOUNTED REAR STOP- LIGHT
B550A01S-DAT (Not all models)
In addition to the lower-mounted rear stoplights on either side of the car, the high mounted rear stoplight in the cen-tre of the rear window or inserted in the rear spoiler also lights when the brakes are applied. HLC2124
PARKING BRAKE
The parking brake must always be set when the vehicle is to be left unat- tended. When the parking brake is ap- plied, and the ignition key is at the "ON"position, the parking brake warning light will be illuminated. Before driving the vehicle, the parking brake must be fullyreleased and the warning light extin- guished.
o To set the parking brake, apply the foot brake and pull the parking brake lever up.
o To release the parking brake, apply the foot brake and pull up the parkingbrake lever slightly. Depress thebutton and lower the lever.
SB380A1-E
SB370A1-E INTERIOR REARVIEW MIRROR The interior mirror is of the day/night type to enable the glare of headlightsfrom following vehicles to be eliminated during night time driving. The tab located at the bottom of themirror should be set to the position nearest the windscreen for normal day time driving, and flipped towards therear of the vehicle to eliminate glare during night time driving. To adjust the field of vision, the mirror may be movedby hand upon the mounting. NOTE: The mirror should always be ad- justed prior to setting the vehicle inmotion. HLC3024-D
HLC2112

1CONTROLS AND EQUIPMENT
70STEERING WHEEL TILT LEVER
!
B600A01A-EAT (Not all models)
To adjust the steering wheel:
1. Push the lever downward to unlock.
2. Raise or lower the steering wheel to the desired position.
3. After adjustment, securely tighten
the lever by pulling it upward.
WARNING:
Do not attempt to adjust the steeringwheel whilst driving as this may result in loss of control of the vehicle and result in death or serious injury. HLC2048-D
B580A01A-D
SUN VISOR
!
Your Hyundai is equipped with sun visors to give the driver and front pas-senger either frontal or sideward shade. The sun visors are fitted on both sides on all models. To reduce glare or toshut out direct rays of the sun, turn the sun visor down to block the annoy- ance. A ticket holder is provided on theback of the sun visor for the driver. Vanity mirrors are provided on the back of the sun visor for the driver andthe front passenger (Not all models). NOTE: The Supplemental Restraint Sys- tem (SRS) label containing useful information can be found on thefront of each sun visor.
WARNING:
Do not place the sun visor in such a manner that it obscures visibility of the roadway, traffic or other ob-jects.
B580A01TB-EAT
HLC2105-DType A
Type B
Type A
Type B

2
DRIVING YOUR HYUNDAI
3TO START THE ENGINEBEFORE STARTING THE ENGINE
!
C020A01O-EAT Before you start the engine, you should always:
1. Look around the vehicle to be sure
there are no flat tyres, puddles of oil or water or other indications of pos- sible trouble.
2. After entering the car, check to be sure the parking brake is engaged.
3. Check that all windows, and lights are clean.
4. Check that the interior and exterior
mirrors are clean and in position.
5. Check your seat, seatback and headrestraint to be sure they are intheir proper positions.
6. Close all the doors.
7. Fasten your seat belt and be sure
that all other occupants have fas- tened theirs.
8. Turn off all lights and accessories
that are not needed.
9. When you turn the ignition switch to "ON" check that all appropriate warn-ing lights are operating and that youhave sufficient fuel. 10.Check the operation of warning
lights and all bulbs when key is inthe "ON" position.
WARNING: (DIESEL ENGINE)
To ensure that sufficient vacuum exists within the brake system dur- ing cold weather start-up condi- tions, it is necessary to run theengine at idle for several seconds after starting the engine. SC040A1-F COMBINATION IGNITION SWITCH AND STEERING LOCK
o If your Hyundai is equipped with a
manual transaxle, place the shift lever in neutral and depress the clutch pedal fully.
o If your Hyundai has an automatic
transaxle, place the shift lever in "P"(park).
o To start the engine, insert the igni- tion key and turn it to the "START"position. Release it as soon as the engine starts. Do not hold the key inthe "START" position for more than 15 seconds.
NOTE: For safety, the engine will not start if the shift lever is not in "P" or "N" position (Automatic Transaxle).

2DRIVING YOUR HYUNDAI
18
SC170E1-E Windscreen Washers and Wip- ers The windscreen washer bottle should be filled with a solution of water and aproprietary winter screen wash addi- tive. The windscreen wipers should not be used if the blades are frozen tothe windscreen or if they are covered with snow, before this is removed. NOTE: Never allow undiluted screen washer fluid additive to spill upon the paintwork or use engine cool- ant anti-freeze since damage to thepaintwork may result.
o When driving in extreme conditions,the windscreen wiper blades may fail to clear the screen properly due to the formation of ice upon theblade edge. It will therefore be nec- essary to periodically remove such ice to restore their efficiency.
o If the power operated door mirrors become frozen, attempts to adjustthese may damage the mechanism.
ZC170D1-E Door Locks Should the door lock mechanism be- come frozen, a proprietary lock de-icershould be used. Alternatively, warm- ing the door key may thaw the door lock. However, the key should behandled carefully to avoid burning the fingers. Never attempt to thaw a frozen doorlock using hot water, since the water will eventually freeze and compound the problem. NOTE: The proper temperature for using the immobiliser key is from -40°F to176°F (-40°C to 80°C). If you heat the immobiliser key over 176°F (80°C) to open the frozen lock, it may causedamage to the transponder in its head.
ZC170C1-E Anti-freeze/Corrosion inhibitor The cooling system must always con- tain an Ethylene-Glycol based anti-freeze solution. The system is filled during manufacture with solution of the correct strength which should bechecked before the onset of winter and adjusted or changed as required. NOTE: The anti-freeze solution contains a corrosion inhibitor to prevent deg- radation of the aluminum castingscontained within the engine. There- fore, never, drain the system and refill with water only. In addition, anti-freeze solution must ALWAYS be used in vehicles fittedwith air conditioning, to prevent the heater matrix from freezing and sub- sequently bursting with the refrigera-tion system in use.

6
OWNER MAINTENANCE
39
G200E01A-GAT Inner Panel
HLC5031 PROTECTED COMPONENTS
Hazard warning, Back-up lamp switch, Transaxle range switch, A/T shift & key lock control module
ETACM, Pre-Excitation resistor, Instrument cluster, Seat belt timer Instrument cluster Air bag
ECM, A/T shift lever, Transaxle range switch, Mass air flow sensor,
Vehicle speed sensor, Water sensor
Power door lock
Hazard warning, ETACM
Stop lamp, A/T shift lever, A/T key interlock solenoid Rear window defogger
Head lamp, Power window, Head lamp leveling, Head lamp washer,
ETACM, Front fog lamp, Blower control, Rear intermittent washer, Fuel filter relayFront wiper & washer Seat warmer ABS control, ABS bleedingDigital clock, Audio, A/T shift & key lock control module Cigarette lighter
Power outside mirrorRear window & outside mirror defogger Rear wiper
FUSE RATING
10A 10A 10A15A 10A10A 10A 10A20A 10A20A 20A10A 10A 15A10A 10A 20A
FUSE
1 2 34 56 7 89
10 11 1213 14 1516 17 18

10INDEX
4
I Ignition Sw itch ............................................................. 2-3
Immobilizer S ystem ..................................................... 1-5
Instrument Cluster and Indicator ..............................1-38
Interior Light
Interior light ............................................................ 1-63
Map light ................................................................ 1-62
JJump Starting .............................................................. 3-3
K
Key .............................................................................. 1-5 If you lose your keys ............................................. 3-14
Positions ................................................................... 2-4
Keyless Entry System ............................................... 1-10
LLubrication Chart ......................................................... 9-4
M Maintenance Intervals Explanation of scheduled maintenance items ......... 5-7
Maintenance and servicing requirements ................ 5-2
Maintenance under severe usage conditions .......... 5-6
Scheduled maintenance ............. .............................. 5-3
Mirrors
Interior rearview mirror ........................................... 1-66
Outside rearview mirror ...................... ...................1-64
Outside rearview mirror heater .............................. 1-65OOdometer / Trip
Odometer ....................................... 1-48
P Parking Brake ........................................................... 1-66
Pollen Filter ...................................................... 1-80, 6-21
Power Steering Fluid Level .......................................6-27
Power Windows ........................................................ 1-11
RRear S eat .................................................................. 1-15
Folding rear seatbacks ..................... ..................... 1-16
Head restraint adjustm ent ...................................... 1-14
Running In Your New Hyundai ................................... 1-4
SSeat Front seat ............................................................... 1-13
Rear seat ............................................................... 1-15
Rear seat entry (3-door model) ............................. 1-15
Seat Belts
3-Point type ............................................................ 1-20
Adjustable height .................................................... 1-19
Adjusting your seat belt ............. ............................ 1-20
Care of seat belts .................................................. 1-19
Precautions ............................................................ 1-18
Pre-tensioner seat bel t ........................................... 1-29
Sparking Plugs Replacement ....................................6-12
Speedometer ............................................................. 1-47
Starting ........................................................................ 2-5