height adjustment Hyundai Accent 2006 Owner's Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2006, Model line: Accent, Model: Hyundai Accent 2006Pages: 599, PDF Size: 17.59 MB
Page 31 of 599
1
FEATURES OF YOUR HYUNDAI
17
B100A01Y-AAT SEAT WARMER (If Installed) The seat warmer is provided to warm the front seats during cold weather. With the ignition key in the "ON" posi- tion, push either of the switches towarm the driver's seat or the passenger's seat. During mild weather or under conditionsthat the operation of the seat warmer is not needed, keep the switches in the "OFF" position.
B080F01S-AAT Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed)
To raise or lower the front part of the seat cushion, turn the front knob for- ward or rearward. To raise or lower the rear part of the seat cushion, turn therear knob forward or rearward.o Do not adjust the headrest hejght while the vehicle is in motion.
B080F01MC
OMC025033
B080G01A-GAT Adjusting Armrest Angle (Driver's side only) (If Installed)
OMC025031
The armrest will be raised or lowered manually. To raise the armrest, pull it up. To lower it, press the armrest down.
Page 39 of 599
1
FEATURES OF YOUR HYUNDAI
25
B160C01A-AAT Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can becleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not beused because they may damage and weaken the fabric. B160D01A-AAT When to Replace Seat Belts Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an acci- dent. This should be done even if nodamage is visible. Additional questions concerning seat belt operation should be directed to your Hyundai Dealer.
!
B170A01MC-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT(If Installed)
B170A01MC
You can adjust the height of the shoul- der belt anchor to one of the 5 positions for maximum comfort and safety.If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection.The shoulder portion should be ad- justed so that it lies across your chest and midway over your shoulder nearestthe door and not your neck. To adjust the height of the seat beltanchor, lower or raise the height ad-juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing theheight adjuster button. Release the button to lock the anchor into position. Try sliding the height ad-juster to make sure that it has locked into the position.
WARNING:
o The height adjuster must be in the locked position when the vehicle is moving.
o The misadjustment of height of
the shoulder belt could reduce theeffectiveness of the seat belt in a crash.
Page 279 of 599
10
INDEX
3
D Door Central door locks .................................................... 1-8
Door locks ................................................................ 1-7
Locking, unlocking front doors with a key ............... 1-7
Drink Holder .............................................................. 1-69
Drive Belts ................................................................ 6-27
Driving Economical driving ................................................. 2-17
Smooth cornering ................................................... 2-18
Winter driving ......................................................... 2-18
EEmission Control Syst em ........................................... 7-2
Engine
Before starting the engine ....................................... 2-3
Compartment ........................................................... 6-2
Coolant ................................................................... 6-13
Coolant temperature gauge ................................... 1-57
If the engine overheats ............................................ 3-4
Number .................................................................... 8-2
Oil ............................................................................. 6-7
Starting ..................................................................... 2-5
Engine Exhaust Can Be Dangerous ........................... 2-2F Fog Light
Front ....................................................................... 1-67
Rear ....................................................................... 1-67
Front Seats
Adjustable front seats ............................................ 1-14
Adjustable headrest s .............................................. 1-15
Adjusting seat forward and rear ward..................... 1-14
Adjusting seatback angle .......................................1-14
Lumbar support control .................. ........................ 1-16
Seat cushion height adjustment............................ 1-16
Seat warmer ........................................................... 1-17
Fuel
Capacity ................................................................... 9-2
Gauge .................................................................... 1-56
Recommendations ................................................... 1-2
Fuel Filler Lid
Remote release ...................................................... 1-80
Fuses ........................................................................ 6-28
Fuse Panel description ............................................. 6-42
G General Checks .......................................................... 6-6
Glove Box ................................................................. 1-74
Page 298 of 599
1FEATURES OF YOUR HYUNDAI
16
B100A01A-GAT SEAT WARMER (If Installed)
The seat warmer is provided to warm the front seats during cold weather. With the ignition key in the "ON" posi- tion, push either of the switches on therear console to warm the driver's seat or the passenger's seat. During mild weather or under conditionsthat the operation of the seat warmer is not needed, keep the switches in the "OFF" position. B100A01A
B080F01S-AAT Seat Cushion Height Adjustment (Driver's Seat Only) (If Installed)
To raise or lower the front part of the seat cushion, turn the front knob for- ward or rearward. To raise or lower the rear part of the seat cushion, turn therear knob forward or rearward.
HLC2028
B080E01O-AAT Lumbar Support Control
(Driver's Seat Only) (If Installed) To adjust the lumbar support, turn the handle on the outboard or left side of theseat. To increase the amount of lumbar support, pull the lever forward. To de- crease it, push the lever toward therear.
HLC2029
o Do not adjust the headrest hejght
while the vehicle is in motion.
Page 304 of 599
1FEATURES OF YOUR HYUNDAI
22
!
B170A04A-AAT HEIGHT ADJUSTABLE FRONT SEAT SHOULDER BELT(If Installed)
B170A01A
You can adjust the height of the shoul- der belt anchor to one of the 4 positions for maximum comfort and safety.If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection.The shoulder portion should be ad- justed so that it lies across your chest and midway over your shoulder nearestthe door and not your neck. To adjust the height of the seat beltanchor, lower or raise the height ad-juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing theheight adjuster button. Release the button to lock the anchor into position. Try sliding the height ad-juster to make sure that it has locked into the position.
WARNING:
o The height adjuster must be in the locked position when the vehicle is moving.
o The misadjustment of height of
the shoulder belt could reduce theeffectiveness of the seat belt in a crash.
B160C01A-AAT Keep Belts Clean and Dry Seat belts should be kept clean and dry. If belts become dirty, they can becleaned by using a mild soap solution and warm water. Bleach, dye, strong detergents or abrasives should not beused because they may damage and weaken the fabric. B160D01A-AAT When to Replace Seat Belts Entire in-use seat belt assembly or assemblies should be replaced if the vehicle has been involved in an acci- dent. This should be done even if nodamage is visible. Additional questions concerning seat belt operation should be directed to your Hyundai Dealer.
Page 421 of 599
1CONTROLS AND EQUIPMENT
14
!
SB070D2-E Head Restraint Adjustment To raise the head restraint, pull it up. To lower it, push it down whilst pressingthe lock knob. For maximum effective- ness in the event of an accident, the restraint must be adjusted so that therestraint is approximately at the level of the seat occupant's ears. The restraint must never be so adjusted that it iscentred about the level of the seat occupant's neck. WARNING:
o For maximum effectiveness in case of an accident, the head restraint should be adjusted so the top ofthe head restraint is at the same height as the top of the occupant's ears. The use of a cushion thatholds the body away from the seatback is not recommended.
o Do not operate the vehicle with the head restraint removed as severeinjury to an occupant may occur in the event of an accident. Headrestraint may provide protection against severe neck injuries when properly adjusted.
B080D01A
Lock knob
HLC2029-D
SB070E1-E Lumbar Support Adjustment (Driver's seat only)(Not all models) Some models are fitted with adjustable driver seat lumbar support which may be used to increase the amount oflumbar support offered by the seat back. Adjustment is performed by moving the handle at the side of the backrest in aforward direction to increase the sup- port.
Page 422 of 599
15
1
CONTROLS AND EQUIPMENT
HLC2028-D
B080F01S-EAT Seat Cushion Height Adjustment (Driver's seat only)(Not all models) To raise or lower the front part of the seat cushion, turn the front knob for- ward or rearward.To raise or lower the rear part of the seat cushion, turn the rear knob forward or rearward.Clockwise raises the seat, counter- clockwise lowers the seat. B130A02A-EAT REAR SEAT ENTRY (For 3-door model)
HTB258-D
(1)
(2)
The driver's and front passenger's seatback should be tilted to enter the rear seat.By pulling up on the recliner control lever (1) at the outside of the driver's and front passenger's seat, the seatbackwill tilt forward and the seat will auto- matically slide forward. Rear seat occupants can tilt the frontpassenger seatback by depressing the foot lever (2) as shown in the drawing. (Front passenger's seat only)
B080G02A-D
B080F01S-EAT Adjusting Armrest Angle (Driver's seat only) The armrest will be raised or lowered manually. To raise the armrest, pull it up.To lower it, press the armrest down.
Page 423 of 599
1CONTROLS AND EQUIPMENT
16
!WARNING:
o For maximum effectiveness in case of an accident, the headrest should be adjusted so the top of the head- rest is at the same height as the
top of the occupant's ears. Theuse of a cushion that holds the body away from the seatback is not recommended.
o Do not operate vehicle with the headrests removed as severe in-jury to an occupant may occur inthe event of an accident. Head- rests may provide protection against severe neck injuries whenproperly adjusted. B110A03A-EAT Folding Rear Seatbacks
B110A02A
To raise the head restraint, pull it up. To lower it, push it down whilst pressingthe lock knob. For maximum effective- ness in the event of an accident, the restraint must be adjusted so that therestraint is approximately at the level of the seat occupant's ears. The restraint must never be so adjusted that it iscentred about the level of the seat occupant's neck.
!WARNING:
The purpose of the fold-down rear seatbacks is to allow you to carrylonger objects than could otherwise be accommodated. Do not allow pas- sengers to sit on top of the folded-down seatback whilst the car is mov- ing as this is not a proper seating position and no seat belts are avail-able for use when the seatbacks are folded down. This could result in serious injury or death in case of anaccident or a sudden stop. Objects
SB070D2-E REAR SEAT Head Restraint Adjustment(Not all models)
!WARNING:
Passengers sitting in the rear seat should be careful not to accidentally press the foot lever (2) whilst thevehicle is moving. As this may cause the seatback to move forward and injure a front seat occupant.
Page 427 of 599
1CONTROLS AND EQUIPMENT
20
SB090P1-E SEAT BELTS (3-Point Type) To Fasten The Seat Belt The seat belts are fastened by pulling the belt buckle towards the seat belt stalk and inserting the metal tongue ofthe buckle into the stalk. The buckle should be firmly pressed into the stalk until locked which will be indicated byan audible "click". The length of the seat belt webbing will be automatically adjusted by the seatbelt mechanism to allow the wearer maximum freedom of movement whilst the belt is being worn. However, in theevent of rapid deceleration or impact, the belt mechanism will automatically lock. B180A01L-R
B200A01S-GAT Adjusting Your Seat Belt
B200A01A-D
The mechanism will also lock if the seat belt webbing is withdrawn too quicklywhen the belt is being fastened or if attempts are made to withdraw the webbing whilst the vehicle is not onlevel ground. Should the seat belt lock under these conditions, it will be pos- sible to release the mechanism by al-lowing a small amount of webbing to be retracted and the belt withdrawn again.
You should place the belt as low as possible on your hips, not on your waist. If the belt is located too high on your body, you could slide under it incase of accident or a sudden stop. This
!
You can adjust the height of the shoul- der belt anchor to one of the 4 positions.If the height of the adjusting seat belt is too near your neck, you will not be getting the most effective protection.The shoulder portion should be ad- justed so that it lies across your chest and midway over your shoulder nearestthe door and not your neck. To adjust the height of the seat belt anchor, lower or raise the height ad-juster into an appropriate position. To raise the height adjuster, pull it up. To lower it, push it down while pressing theheight adjuster button. Release the button to lock the anchor into position. Try sliding the height ad-juster to make sure that it has locked into the position. WARNING:
o The height adjuster must be in the locked position when the vehicle is moving.
o The misadjustment of height of
the shoulder belt could reduce theeffectiveness of the seat belt in a crash.
Page 597 of 599
10
INDEX
3
Driving Economical driving ................................................. 2-16
Smooth cornering ................................................... 2-17
Winter motoring ...................................................... 2-17
E Emission Control Syst em ........................................... 7-2
Engine Before starting the engine ....................................... 2-3
Compartment ........................................................... 6-2
Coolant ..................................................................... 6-9
Coolant temperature gauge ................................... 1-46
If the engine overheats ............................................ 3-5
Number .................................................................... 8-2
Oil ............................................................................. 6-5
Starting ..................................................................... 2-5
Engine Exhaust Can Be Dangerous ........................... 2-2
FFog Light Front ....................................................................... 1-56
Rear ....................................................................... 1-56
Front Seats
Head restraint adjustment...................................... 1-14
Lumbar support adjustment ................................... 1-14
Seat cushion height adjustment............................ 1-15
Seat rake adj ustment............................................. 1-13
Seat recline adjustment .............. ...........................1-13Fuel
Capacity ................................................................... 9-2
Gauge .................................................................... 1-46
Recommendations ................................................... 1-2
Fuel Filler Lid
Remote release ...................................................... 1-68
Fuses ........................................................................ 6-24
Fuse Panel description ............................................. 6-37
G Glove Box ................................................................. 1-63
H Hazard Warning System ........................................... 1-55
Headlight Aiming Adjustment ....................................6-28
Headlight Leveling Device Syst em ...........................1-54
Heated Rear Window ................................................ 1-55
Heating and Cooling Control ..................................... 1-72
Heating and Ventilation ............................................. 1-73
Air flow control ....................................................... 1-74
Air intake control .................................................... 1-73
Bi-level heating ....................................................... 1-77
Defrost/Defogging .................................................. 1-77
Fan speed control .................................................. 1-73
Temperature control ............................................... 1-76
High-Mounted Rear Stop light.................................... 1-66
Horn .......................................................................... 1-71