light Hyundai Elantra 2006 Manual PDF

6 DO-IT-YOURSELF MAINTENANCE
36HEADLIGHT AIMING ADJUSTMENT
G290A02E-GAT Before performing aiming adjustment,
make sure of the following.
1. Keep all tires inflated to the correct
pressure.
2. Place the vehicle on level ground and press the front bumper and rear bumper down several times.(Place the vehicle at a distance of 3,000 mm (118 in.) from the test wall.)
3. See that the vehicle is unloaded
(except for full levels of coolant,engine oil and fuel, and spare tire, jack, and tools). Have the driver or equivalent weight placed in driver'sseat.
4. Clean the head lights lenses and
turn on the headlights (low beam).
!WARNING:
Be sure to carefully wipe away any water drained out in this manner, because the fuel mixed in the wa-ter might be ignited and result in a fire.
G300B01A
1. Loosen the drain plug at the bottom of the fuel filter.
2. Tighten the drain plug when water no longer comes out.
3. Check to be sure that the warning lamp illuminates when the ignition key is turned to "ON", and that it goes off when the engine is started. If in doubt, consult your nearest authorized HYUNDAI dealer.
NOTE: It is recommended that water ac- cumulated in the fuel filter shouldbe removed by an authorized Hyundai dealer.

6
DO-IT-YOURSELF MAINTENANCE
37
Vertical Aiming
Horizontal Aiming
G290B03E-GAT
Adjustment After Headlight Assembly Replacement
G290B01L
LW
H
H Cut-off line be checked using an aiming screen as shown in the illustration. Turn on theheadlight switch. (Low Beam Position)
1. Adjust headlights so that main axis of light is parallel to the center lineof the body and is aligned with point"P" shown in the illustration.
2. Dotted lines in the illustration show
the center of the the headlights. Specifications: "H": Horizontal center line of headlights from ground.Low beam : 639 mm (25.2 in.) High beam : 619 mm (23.3 in.) "W": Distance between each headlightcenter.Low beam : 1124 mm (44.2 in.) High beam : 840 mm (33.0 in.) "L": Distance between the headlights andthe wall that the lights are testedagainst.: 3,000 mm (118 in.).
"P"
30mm (1.18 in.) Vertical line
G290A02E
5. Open the hood.
6. Draw the vertical line (through the center of each headlight beam pat-tern) and the horizontal line (through the center of each headlight beam pattern) on the aiming screen.And then, draw a horizontal paral-lel line at 30 mm (1.18 in.) underthe horizontal line.
7. Adjust each cut-off line of the low beam to the parallel line with aphillips screwdriver - VERTICAL AIMING.
8. Adjust each cut-off line of the low beam to the each vertical line with a phillips screwdriver - HORIZON-TAL AIMING. LHD
Horizontal line
Ground line
G290B01L-D
L
W
H
H Cut-off line
"P"
30mm (1.18 in.)
Vertical line
Horizontal line
Ground line
RHD
If the vehicle has had front body repair
and the headlight assembly has been replaced, the headlight aiming should

6 DO-IT-YOURSELF MAINTENANCE
38
4. Using a spanner of the correct
size, remove the headlight assem- bly mounting bolts.
HXDFL1009
5. Disconnect the power cord from the back of the headlight.
REPLACEMENT OF LIGHT BULBS
G260A03A-AAT Before attempting to replace a head- light bulb, be sure the switch is turned to the "OFF" position. The next paragraph shows how to reach the headlight bulbs so they may be changed. Be sure to replacethe burned-out bulb with one of the same number and wattage rating. See page 6-45 for the wattage de- scriptions.
CAUTION:
Keep the lamps out of contact with petroleum products, such as oil, gasoline, etc.
!
Replacement instructions:
1. Allow the bulb to cool. Wear eye protection.
2. Open the engine hood.
3. Always grasp the bulb by its plastic base, avoid touching the glass. G270A01E
G270A01E-GAT
HEADLIGHT AND FRONT TURN SIGNAL LIGHT
High beam Low beam
Turn signal light
HXDFL1022

6
DO-IT-YOURSELF MAINTENANCE
39
HXDFL1011
7. Push the bulb spring to remove the headlight bulb. HXDFL1010
6. Turn the plastic cover counterclock- wise and remove it. 8. Remove the protective cap from
the replacement bulb and install the new bulb by matching the plas- tic base with the headlight hole. Retighten the bulb spring and re-connect the power cord.
9. Use the protective cap and carton to promptly dispose of the old bulb.
10.Check for proper headlight aim.
(1) High beam (2) Low beam (3) Front turn signal light HXDFL1013-1
(1)
(2)(3)
!
G270A03O
WARNING:
This halogen bulb contains gas under pressure and if impacted could shatter, resulting in flyingfragments. Always wear eye pro- tection when servicing the bulb. Protect the bulb against abrasionsor scratches and against liquids when lighted. Turn the bulb on only when installing in a head-light. Replace the headlight if dam- aged or cracked. Keep the bulb out of the reach of children anddispose of the used bulb with care.

6 DO-IT-YOURSELF MAINTENANCE
40
4. To replace the rear combination
light, remove it from the bulb holder and install the new bulb.
(1) Stop/Tail light
(2) Rear turn signal light
(3) Back up light
(4) Rear Fog Light
HXDFL1016
HXDFL1014
G270D01E-GAT
REAR COMBINATION LIGHT (Rear Fog Light, Stop / Tail Light,
Back up light and Rear Turn Sig- nal Light)
4Door
1. Open the trunk lid.
2. Unscrew and remove the cover on the inside of the rear luggage trim. 3. Remove the mounting screws of
the rear combination light with a spanner. HXDFL1015
(1)
(2)
(3) G270D01E
(4)
(2) (3)
(1)
Except European Community European Community Only

6
DO-IT-YOURSELF MAINTENANCE
41
HXDFL334
5Door(Luggage compartment)
1. Open the tail gate.
2. Remove the mounting screws of the rear combination light with a flat blade screwdriver.
HXDFL1017
3. To replace the rear combination light, remove it from the bulb holder and install the new bulb.
(1) Stop/Tail light(2) Rear turn signal light HXDFL335
HXDFL342
5Door (Tail gate)
1. Open the tail gate.
2. Remove the cover with a flat blade screwdriver.
(1) (2)

6 DO-IT-YOURSELF MAINTENANCE
42
G270C01L-GAT
LUGGAGE COMPARTMENT LIGHT
4Door
1. Open the trunk lid.
2. Remove the plastic cover with a flat blade screwdriver.
3. Disconnect the power cord. HXDFL341B
HTB284
4. Replace with a new bulb.
HXDFL341A
HXDFL333 HXDFL332
Back up light
3. To replace the rear combination light, remove it from the bulb holder and install the new bulb.
Rear Fog light

6
DO-IT-YOURSELF MAINTENANCE
43
5Door
1. Open the tail gate.
2. Remove the luggage compartment light cover on the right side pack- age tray panel with pushing it. HXDFL341
HTB284
3. Disconnect the power cord.
4. Replace with a new bulb.
HTB277
G270E01A-GAT
SIDE REPEATER (If installed)
G270E01A
1. Push the cover toward the front of vehicle and remove it.
2. Disconnect the power cord.
HXDFL343

6 DO-IT-YOURSELF MAINTENANCE
44
G270G01E-GAT
INTERIOR LIGHT
Room Light
HXDFL1020
1. Remove the plastic cover with a flat blade screwdriver.
2. Replace with a new bulb. HXDFL1021
Screwdriver G270H01E-GAT
Map Light (If installed)
B460D02E
1. Remove the plastic cover with a flat blade screwdriver.
G270H01E
HTB278
3. Replace with a new bulb.
2. Replace with a new bulb.

6
DO-IT-YOURSELF MAINTENANCE
45BULB WATTAGE
1357
4
G280A05E-GAT
G280A03E
16
31110
8
4 DOOR
5 DOOR
111012
8132
12
99
Part Name
High mounted rear stop light Luggage compartment light License plate light Rear fog light (If installed) Back -up light
No.
8 9
10 11 12 13
Wattage
55
55/5
51 215
1010
5 Socket type
BA 15s -
S8.5/8.5 S8.5/8.5 BA 15s
BAY 15d BA 15s
W2.1×9.5D
BA 15s
Part Name
Head Light (High beam) Head Light (Low beam) / Front Position Light Front Fog Light (If installed) Front Turn Signal LightSide Repeater (If installed) Door Edge Warning Light
No
.
1 2 3 45 67
Socket type P14,5s
PX 26d/
W2.1X9.5d P22d
BA15s
W2.1X9.5d W2.1×9.5D
S8.5/8.5
W2.1X9.5dWattage
5 5
2121
21/5
Rear combination light
4 Door5 Door
Map Light Room Light
4 Door 5 Door21
2,6(LED)
Turn signal light Stop/tail light
16 27
Interior