ABS Hyundai H350 2016 Owner's Guide
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2016, Model line: H350, Model: Hyundai H350 2016Pages: 473, PDF Size: 26.4 MB
Page 425 of 473
7-62
Maintenance
Engine compartment main fuse panel
No.Fuse ratingFuse Name Circuit Protected
110A2
A/CONA/C Compressor PASS
215A4
ECUEngine Control Module (Permanent Battery (+))
310A1
A/CONA/C Compressor CAB
410A1
SENSORElectric VGT Actuator, EGR Cooling Bypass, UH_BOX(Fuel Pump Relay 'S')
510ASPARE
620A1
ECUEngine Control Module (Battery (+))
710A2
SENSORUH_BOX(A/CON1 Relay 'S', A/CON2 Relay 'S', CONDENSER FAN Relay LH,RH1/2 'S')
820A2
ECUEngine Control Module (Battery (+))
910A3
SENSORLAMBDA Sensor
107.5ABACK UP LAMPRear Combi Lamp Left/Right (Back Up), Inside Mirror (Reverse), Trailer Module (Back Up),
Vehicle Dynamic Control Module (Reverse Gear Switch), Reverse Warning Buzzer
117.5A3
ABSAnti-Lock Brake Module (IG1), Vehicle Dynamic Control Module (IG1), Steering Angle Sensor (IG1)
127.5A5
SENSORAir Flow Sensor, Engine Control Module (TERMINAL15(IG1 INPUT))
Page 426 of 473
7-63
7
Maintenance
No.Fuse ratingFuse Name Circuit Protected
137.5AINHIBITORUH_BOX(Start Inhibit Relay 'S')
1460A3
B+Smart Junction Box (B+3)
1560AVDCVehicle Dynamic Control Module (B+ Pump Motor)
1640A2
ABSAnti-Lock Brake Module (B+ Solenoid Valve), Vehicle Dynamic Control Module(B+ Solenoid
Valve)
1740A1
ABSAnti-Lock Brake Module (B+ Pump Motor)
1860A2
B+Smart Junction Box (B+2)
1980AGLOWGlow Relay Module (Plus Direct)
2050A4
B+Smart Junction Box (B+4)
2150AEMSEngine Management System Block (B+)
2215AHORNHORN
2310APTOPTO Magnetic Valve
2420AF/PUMPFuel Pump Sender (Fuel Pump Motor(+))
Page 433 of 473
7-70
Maintenance
Turn signal light/Position light
Turn signal light
1.Turn off the engine and open thehood.
2.Remove the socket from the assembly by turning the socket
counterclockwise until the tabs on
the socket align with the slots on
the assembly.
3.Remove the bulb from the socket by pressing it in and rotating it
counterclockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket
4.Insert a new bulb by inserting it into the socket and rotating it until it
locks into place.
5.Install the socket in the assembly by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
Position light
If the light bulb does not operate, we recommend that the system be
checked by an authorized HYUNDAI
dealer.
Front fog light bulbs
(if equipped)
1.Remove the front bumper under cover.
2.Reach your hand into the back of the front bumper.
3.Disconnect the power connector from the socket.
4.Remove the bulb-socket from the housing by turning the socket
counter clockwise until the tabs on
the socket align with the slots onthe housing.
5.Install the new bulb-socket into the housing by aligning the tabs on the
socket with the slots in the hous-
ing. Push the socket into the hous-
ing and turn the socket clockwise.
6.Connect the power connector to the socket.
7.Reinstall the front bumper under cover.
Headlight and front fog light
aiming (for Europe)
Headlight aiming
1.Inflate the tires to the specified
pressure and remove any loads
from the vehicle except the driver,
spare tire, and tools.
OEU074061
OEU074049■■Projection type
■■MFR type
Page 439 of 473
1.Open the rear door.
2.Loosen the light assembly retain-ing screws with a cross-tip screw-
driver.
3.Remove the rear combination light assembly from the body of the
vehicle. 4.Remove the socket from the
assembly by turning the socket
counter clockwise until the tabs on
the socket align with the slots on
the assembly.
5.Remove the bulb from the socket by pressing it in and rotating it
counter clockwise until the tabs on
the bulb align with the slots in the
socket. Pull the bulb out of the
socket.
6.Insert a new bulb by inserting it into the socket and rotating it until it
locks into place. 7.Install the socket in the assembly
by aligning the tabs on the socket
with the slots in the assembly.
Push the socket into the assembly
and turn the socket clockwise.
8.Reinstall the light assembly to the body of the vehicle.
7-76
Maintenance
OEU074053OEU074051
Page 441 of 473
7-78
Maintenance
High mounted stop light bulb replacement (if equipped)
If the light does not operate, we rec-
ommend that the system be checked
by an authorized HYUNDAI dealer.
License plate light bulb replacement (if equipped)
1.Remove the lens by pressing thetabs.
2.Remove the socket from the lens.
3.Remove the bulb by pulling it straight out.
4.Install a new bulb in the socket and install the socket to the lens.
5.Reinstall the lens securely.
Interior light bulb replacement
1.Using a flat-blade screwdriver, gently pry the lens from the interior light housing.
2.Remove the bulb by pulling it straight out.
OEU074052OEU074054
OEU074031
OEU074032
■Map lamp
■Room lamp
Page 442 of 473
7-79
7
Maintenance
3.Install a new bulb in the socket.
4.Align the lens tabs with the interiorlight housing notches and snap the
lens into place.
Exterior care
Exterior general caution
It is very important to follow the label
directions when using any chemical
cleaner or polish. Read all warningand caution statements that appearon the label.
Finish maintenance
Washing
To help protect your vehicle’s finish
from rust and deterioration, wash itthoroughly and frequently at least
once a month with lukewarm or cold
water.
If you use your vehicle for off-road
driving, you should wash it after each
off-road trip. Pay special attention to
the removal of any accumulation of
salt, dirt, mud, and other foreign
materials. Make sure the drain holes
in the lower edges of the doors and
rocker panels are kept clear andclean.
Insects, tar, tree sap, bird droppings,
industrial pollution and similar
deposits can damage your vehicle’s
finish if not removed immediately.
Even prompt washing with plain
water may not completely remove all
these deposits.
A mild soap, safe for use on painted
surfaces, may be used.
After washing, rinse the vehicle thor-
oughly with lukewarm or cold water.
Do not allow soap to dry on the fin-ish.
Prior to working on the Interior
Lights, ensure that the “OFF”
button is depressed to avoid
burning your fingers or receiv-
ing an electric shock.
WARNING
Use care not to dirty or damage
lens, lens tab, and plastic hous-ings.
CAUTION
AA
PPPPEEAA RRAA NN CCEE CC AA RREE
Page 450 of 473
7-87
7
Maintenance
The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Service
Passport in your vehicle.
Your vehicle is equipped with an emission control system to meet all
emission regulations. There are three emission control
systems which are as follows.
(1) Crankcase emission control sys-tem
(2) Evaporative emission control sys- tem
(3) Exhaust emission control systemIn order to assure the proper function
of the emission control systems, it is
recommended that you have your
vehicle inspected and maintained by
an authorized HYUNDAI dealer orother repair shops that use qualifiedtechnicians in accordance with the
maintenance schedule in this manu-al.1. Crankcase emission control system
The positive crankcase ventilation
system is employed to prevent air
pollution caused by blow-by gases
being emitted from the crankcase.This system supplies fresh filtered air
to the crankcase through the air
intake hose. Inside the crankcase,
the fresh air mixes with blow-by
gases, which then pass through the
PCV valve into the induction system.
2. Evaporative emission con-trol System
The Evaporative Emission Control
System is designed to prevent fuel
vapors from escaping into the atmos-
phere.
Canister
Fuel vapors generated inside the fueltank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in
the canister are drawn into the surgetank through the purge control sole-
noid valve.
Purge Control Solenoid Valve
(PCSV)
The purge control solenoid valve is
controlled by the Engine Control
Module (ECM); when the engine
coolant temperature is low during
idling, the PCSV closes so that evap-
orated fuel is not taken into the
engine. After the engine warms-up
during ordinary driving, the PCSV
opens to introduce evaporated fuel to
the engine.
EE MM IISS SSIIOO NN CC OO NNTTRR OO LL SS YY SSTT EEMM
Page 467 of 473
I-2Active eco system .........................................................5-40
Active eco operation ..................................................5-40
Limitation of active eco operation:............................5-41
When active eco is activated: ....................................5-41
Adjustable speed limit device (ASLD) ........................3-34
Air bag - supplemental restraint system .......................2-25 Air bag warning light.................................................2-28
Do not install a child restraint on the front passenger seat ..........................................................2-27
Driver's and front passenger's air bag........................2-31
How does the air bag operate? ..................................2-26
SRS care.....................................................................2-39
SRS components and functions .................................2-29
Additional safety precautions .......................................2-40
Air bag warning labels .................................................2-42
Air cleaner ....................................................................7-31
Air conditioner compressor label .................................8-11
Air conditioning system .................................................8-3
Appearance care ...........................................................7-79
Battery...........................................................................7-37 Battery capacity label ................................................7-40
Battery recharging......................................................7-40
For best battery service ..............................................7-37
Reset items .................................................................7-41 Before driving .................................................................5-3
Before entering the vehicle ..........................................5-3
Before starting .............................................................5-3
Necessary inspections ..................................................5-3
Brake system.................................................................5-18
Anti-lock brake system (ABS) ..................................5-21
Emergency stop signal (ESS) ....................................5-28
Good braking practices ..............................................5-29
Hill-start assist control (HAC)...................................5-27
Parking brake .............................................................5-19
Power brakes..............................................................5-18
Vehicle dynamic control (VDC) ................................5-24
Brake/Clutch fluid ........................................................7-27
Bulb wattage ...................................................................8-4
Cargo bed (for van) ....................................................3-129
Caring for disc ................................................................4-5
CD Player (For RDS Model)........................................4-13
CD Player .....................................................................4-16
Ceiling ventilator ........................................................3-122
Climate control air filter ...............................................7-33
Climate control system ...............................................3-110
Checking the amount of air conditioner refrigerant and compressor lubricant.......................................3-120
Climate control air filter ..........................................3-119
Fuel-fired heater .......................................................3-119
Heating and air conditioning....................................3-111
Index
A
C
B