Alarm remove Hyundai H350 2016 Owner's Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2016, Model line: H350, Model: Hyundai H350 2016Pages: 473, PDF Size: 26.4 MB
Page 72 of 473
3-10
Convenient features of your vehicle
Armed stage
Park the vehicle and stop the engine.
Arm the system as described below.
1.Remove the ignition key from theignition switch or turn off the
engine.
2.Make sure that all doors (and rear door) and the engine hood areclosed and latched.
3.Lock the doors by depressing the door lock button on the transmitter.After completion of the steps
above, the hazard warning lights
will blink once to indicate that the
system is armed.
If any door, rear door remains
open, the hazard warning lights
won't operate and theft-alarm will
not arm. Close the door and try
again to lock the doors. If any door (and rear door) remains
open, the hazard warning lights
won't operate and theft-alarm will
not arm. Close the door and try
again to lock the doors. If engine hood remains open, the
hazard warning lights won't oper-
ate and theft-alarm will not arm.
Close the engine hood. The hazard
warning lights blink once and theft-
alarm arms.
Do not arm the system until all passengers have left the vehi-
cle. If the system is armed while
a passenger(s) remains in the
vehicle, the alarm may be acti-
vated when the remaining pas-
senger(s) leave the vehicle. If
any door, rear door or enginehood is opened within 30 sec-onds after entering the armed
stage, the system is disarmed to
prevent unnecessary alarm.
Theft-alarm stage
The alarm will be activated if any of
the following occurs while the system
is armed.
A front or rear door is opened with-out using transmitter.
The rear door is opened without using transmitter.
The engine hood is opened.The siren will sound and the hazard
warning lights will blink continuously
for 27 seconds, unless the system is
disarmed. To turn off the system,
unlock the doors with the transmitter.
Page 81 of 473
3-19
Convenient features of your vehicle
Operation and obstacle detec- tion
The electrical step (1) is equipped
with a device to detect an obstacle infront.
When the electrical step comes into contact with an obstacle while
extending out, its movement auto-
matically stops with 'short but repeti-
tive' warning alarms.
To fully extend out the electrical step
again, take the following steps. First,
remove the obstacle. Second, closeand then re-open the mid-sliding
door. Finally, repetitively press the
STEP switch to turn OFF and turn
ON the electrical step.
If the electrical step hinders load-
ing, you can block the step when
opening the sliding door by using
the obstruction detection. Thismeans that the electrical step
remains retracted and a fork-lift
truck or another lifting vehicle can
move closer to the load compart-ment.
Electrical step warning alarm
1.Continuous beeping sound You will hear this type of alarm,
whenever the electrical step oper-
ates.
2.Short beeping sound (short & repetitive)
You will hear this type of alarm,
when the parking/foot brakes arereleased.
In this case, apply the parking/foot
brakes for your safety.
3.Long beeping sound (long & repet- itive)
You will hear this type of alarm,
when the operation of the electrical
step temporarily fails due to opera-
tional/electrical problems.
In this case, remove foreign sub-
stances, such as sand, mud, and
ice. Then, re-press the STEP
switch to operate the electrical
step.
However, if the problem persists,
manually push in the electrical step
as a safety measure. Still, we rec-
ommend you to have the electrical
step repaired by an authorized
HYUNDAI dealer.
NOTICE
3
Never drive your vehicle, when
the electrical step is extended
out. It may cause an accident,
strike with other vehicles, and
even injure passers-by. Always
drive your vehicle with the elec-
trical step fully retracted in.
WARNING
Page 82 of 473
3-20
The emergency measures,
which you may take in case ofthe electrical-step failures.
The step friction surface is con-taminated with the foreign sub-
stances.
The electrical step may not normally
operate, when its friction surface is
contaminated. Repetitively operate
either the step switch or the mid-slid-
ing door 2-to-3 times. When the step
operation completely stops for the
same reason, manually push in the
step and turn OFF the switch.
Remove the foreign substances with
washing equipment at a vehicle
wash (Refer to the regular cleaning
in the chapter 3). Then, turn ON the
step switch, and operate the mid-
sliding door. When the electrical step
does not still normally operate, we
recommend that the electrical step
be checked by an authorized
HYUNDAI dealer.
Step does not operate, after being extended out.
Hold the step in position with the R-
clip, as explained below. Then, turn
OFF the switch and visit a near-by
Hyundai dealer for repair services.
When you hear the warning alarm
while driving, you may stop the alarm
by disconnecting the electrical step
fuse located in the fuse box under
the left side of the driver's seat.
Hold the step in position with the
R-clip
1. Pull R-clips (3) on both rods (1) on the underside of the step out of
their respective pins. Remove
washers (2) and detach both rods(1).
Convenient features of your vehicle
OEU044078