Cce HYUNDAI I20 2023 Owners Manual
[x] Cancel search | Manufacturer: HYUNDAI, Model Year: 2023, Model line: I20, Model: HYUNDAI I20 2023Pages: 649, PDF Size: 12.35 MB
Page 599 of 649
9-40
Maintenance
5. Maximum permissible inflation
pressure
This number is the greatest amount
of air pressure that should be put in
the tyre. Do not exceed the maximum
permissible inflation pressure. Refer to
the Tyre and Loading Information label
for recommended inflation pressure.
6. Maximum load rating
This number indicates the maximum
load in kilograms and pounds that can
be carried by the tyre. When replacing
the tyres on the vehicle, always use a
tyre that has the same load rating as the
factory installed tyre.
7. Uniform tyre quality grading
Quality grades can be found where
applicable on the tyre sidewall between
tread shoulder and maximum section
width.
For example:
TREADWEAR 200
TRACTION AA
TEMPERATURE A
7 U H D G Z H D U
The tread wear grade is a comparative
rating based on the wear rate of the tyre
when tested under controlled conditions
on a specified government test course.
For example, a tyre graded 150 would
wear one-and-a-half times (1½) as well
on the government course as a tyre
graded 100. The relative performance of tyres
depends upon the actual conditions
of their use, however, and may depart
significantly from the norm due to
variations in driving habits, service
practices and differences in road
characteristics and climate.
These grades are molded on the
sidewalls of passenger vehicle tyres. The
tyres available as standard or optional
equipment on your vehicle may vary
with respect to grade.
7 U D F W L R Q $ $ $ % &
The traction grades, from highest to
lowest, are AA, A, B and C. Those grades
represent the tyre’s ability to stop on wet
pavement as measured under controlled
conditions on specified government
test surfaces of asphalt and concrete. A
tyre marked C may have poor traction
performance.
WARNING
The traction grade assigned to this tyre
is based on straight-ahead braking
traction tests, and does not include
acceleration, cornering, hydroplaning,
or peak traction characteristics.
Page 601 of 649
9-42
Maintenance
OTA070039
„ Blade type
NormalBlown
„ Cartridge type
„ Multi fuse
NormalBlown
NormalBlown
A vehicle’s electrical system is protected
from electrical overload damage by
fuses.
This vehicle has 2 (or 3) fuse panels, one
located in the driver’s side panel bolster,
the other in the engine compartment.
If any of your vehicle’s lights,
accessories, or controls do not work,
check the appropriate circuit fuse. If a
fuse has blown, the element inside the
fuse will be melted or broken.
If the electrical system does not work,
first check the driver’s side fuse panel.
Before replacing a blown fuse, turn the
engine and all switches off, and then
disconnect the negative battery cable.
Always replace a blown fuse with one of
the same rating.
If the replacement fuse blows, this
indicates an electrical problem. Avoid
using the system involved and we
recommend that all inspect a HYUNDAI
authorised repairer.
i Information
7 K U H H N L Q G V R I I X V H V D U H X V H G E O D G H W \ S H
I R U O R Z H U D P S H U D J H U D W L Q J V F D U W U L G J H
W \ S H D Q G P X O W L I X V H I R U K L J K H U D P S H U D J H
U D W L Q J V
WARNING
NEVER replace a fuse with anything but
another fuse of the same rating.
[ A higher capacity fuse could cause
damage and possibly cause a fire.
[ Do not install a wire or aluminium
foil instead of the proper fuse -
even as a temporary repair. It may
cause extensive wiring damage and
possibly a fire.
NOTICE
Do not use a screwdriver or any other
metal object to remove fuses because
it may cause a short circuit and damage
the system.
FUSES
Page 641 of 649
9-82
Maintenance
Finish damage repair
Deep scratches or stone chips in the
painted surface must be repaired
promptly. Exposed metal will quickly
rust and may develop into a major repair
expense.
NOTICE
If your vehicle is damaged and requires
any metal repair or replacement,
be sure the body shop applies anti-
corrosion materials to the parts
repaired or replaced.
NOTICE
Matte paint finish vehicle
(if equipped)
In case of matte paint finish vehicles,
it is impossible to modify only the
damaged area and repair of the whole
part is necessary. If the vehicle is
damaged and painting is required, we
recommend that you have your vehicle
maintained and repaired by a HYUNDAI
authorised repairer. Take extreme care,
as it is difficult to restore the quality
after the repair.
Bright-metal maintenance
[ 7 R U H P R Y H U R D G W D U D Q G L Q V H F W V X V H
a tar remover, not a scraper or other
sharp object.
[ 7 R S U R W H F W W K H V X U I D F H V R I E U L J K W P H W D O
parts from corrosion, apply a coating
of wax or chrome preservative and rub
to a high luster.
[ ' X U L Q J Z L Q W H U Z H D W K H U R U L Q F R D V W D O
areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenance
Corrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, accelerated
rusting can occur on underbody parts
such as the fuel lines, frame, floor pan
and exhaust system, even though they
have been treated with rust protection.
Thoroughly flush the vehicle underbody
and wheel openings with lukewarm or
cold water once a month, after off-road
driving and at the end of each winter.
Pay special attention to these areas
because it is difficult to see all the mud
and dirt. It will do more harm than good
to wet down the road grime without
removing it. The lower edges of doors,
rocker panels, and frame members have
drain holes that should not be allowed
to clog with dirt; trapped water in these
areas can cause rusting.
Page 642 of 649
9-83
09
WARNING
After washing the vehicle, test the
brakes whilst driving slowly to see if
they have been affected by water. If
braking performance is impaired, dry
the brakes by applying them lightly
whilst maintaining a slow forward
speed.
Aluminium wheel maintenance
The aluminium wheels are coated with a
clear protective finish.
NOTICE
[ ' R Q R W X V H D Q \ D E U D V L Y H F O H D Q H U
polishing compound, solvent, or wire
brushes on aluminium wheels.
[ & O H D Q W K H Z K H H O Z K H Q L W K D V F R R O H G
[ 8 V H R Q O \ D P L O G V R D S R U Q H X W U D O
detergent, and rinse thoroughly with
water. Also, be sure to clean the
wheels after driving on salted roads.
[ ' R Q R W Z D V K W K H Z K H H O V Z L W K K L J K
speed car wash brushes.
[ ' R Q R W X V H D Q \ F O H D Q V H U F R Q W D L Q L Q J
acid or alkaline detergents.
Corrosion protection
3 U R W H F W L Q J \ R X U Y H K L F O H I U R P F R U U R
V L R Q
By using the most advanced design
and construction practices to combat
corrosion, we produces vehicles of the
highest quality. However, this is only
part of the job. To achieve the long-term
corrosion resistance your vehicle can
deliver, the owner’s cooperation and
assistance is also required.
& R P P R Q F D X V H V R I F R U U R V L R Q
The most common causes of corrosion
on your vehicle are:
[ Road salt, dirt and moisture that is
allowed to accumulate underneath the
vehicle.
[ Removal of paint or protective
coatings; by stones, gravel, abrasion
or minor scrapes and dents which
leave unprotected metal exposed to
corrosion.
+ L J K F R U U R V L R Q D U H D V
If you live in an area where your vehicle
is regularly exposed to corrosive
materials, corrosion protection is
particularly important. Some of the
common causes of accelerated
corrosion are road salts, dust control
chemicals, ocean air and industrial
pollution.
Page 643 of 649
9-84
Maintenance
0 R L V W X U H E U H H G V F R U U R V L R Q
Moisture creates the conditions in
which corrosion is most likely to occur.
For example, corrosion is accelerated
by high humidity, particularly when
temperatures are just above freezing. In
such conditions, the corrosive material is
kept in contact with the vehicle surfaces
by moisture that is slow to evaporate.
Mud is particularly corrosive because
it is slow to dry and holds moisture in
contact with the vehicle. Although the
mud appears to be dry, it can still retain
moisture and promote corrosion.
High temperatures can also accelerate
corrosion of parts that are not properly
ventilated so the moisture can be
dispersed. For all these reasons, it is
particularly important to keep your
vehicle clean and free of mud or
accumulations of other materials. This
applies not only to the visible surfaces
but particularly to the underside of the
vehicle.
7 R K H O S S U H Y H Q W F R U U R V L R Q
You can help prevent corrosion from
getting started by observing the
following:
Keep your vehicle clean
The best way to prevent corrosion is
to keep your vehicle clean and free of
corrosive materials. Attention to the
underside of the vehicle is particularly
important.
[ If you live in a high-corrosion area —
where road salts are used, near the
ocean, areas with industrial pollution,
acid rain, etc.—, you should take extra
care to prevent corrosion. In winter,
hose off the underside of your vehicle
at least once a month and be sure to
clean the underside thoroughly when
winter is over.
[ When cleaning underneath the
vehicle, give particular attention to the
components under the fenders and
other areas that are hidden from view.
Do a thorough job; just dampening the
accumulated mud rather than washing
it away will accelerate corrosion rather
than prevent it. Water under high
pressure and steam are particularly
effective in removing accumulated
mud and corrosive materials.
[ When cleaning lower door panels,
rocker panels and frame members, be
sure that drain holes are kept open so
that moisture can escape and not be
trapped inside to accelerate corrosion.