Eco HYUNDAI I20 2023 Manual Online

5-46
Convenient features
OAC3059027TU
Vehicle without front fog lamp
To turn on the rear fog lamp:
Position the light switch in the headlamp
position, and then turn the light switch
(1) to the rear fog lamp position.
To turn the rear fog lamps off, do one of
the following:

[Turn off the headlamp switch.

[Turn the light switch to the rear fog
lamp position again.
Battery saver function
The purpose of this feature is to prevent
the battery from being discharged.
The system automatically turns off the
position lamp when the driver turns the
engine off and opens the driver-side
door.
With this feature, the position lamps will
turn off automatically if the driver parks
on the side of road at night.
If necessary, to keep the lamps on when
the engine is turned off, perform the
following:
1) Open the driver-side door.
2) Turn the position lamps OFF and ON
again using the light switch on the
steering column.
Headlamps delay function
(if equipped)
If you place the ignition switch in the
ACC or OFF position with the headlamps
ON, the headlamps (and/or position
lamps) remain on for about 5 minutes.
However, with the engine off if the
GULYHU
TVGRRULVRSHQHGDQGFORVHGWKH
headlamps (and/or position lamps) are
turned off after 15 seconds.
The headlamps (and/or position lamps)
can be turned off by pressing the lock
button on the remote key or smart
key twice or turning the light switch to
the OFF or AUTO position. However, if
you turn the light switch to the AUTO
position when it is dark outside, the
headlamps will not be turned off.

5-48
Convenient features
WARNING
If the function does not work properly,
we recommend that the system be
inspected by a HYUNDAI authorised
repairer. Do not attempt to inspect or
replace the wiring yourself.
Low Beam Assist-Static light
Whilst driving a corner, for greater
visibility and safety, either the left or
right side Low Beam Assist-Static light
will turn on automatically. The Low
Beam Assist-Static light will turn on
when one of the following conditions
occurs.

[Vehicle speed is less than 6 mph (10
km/h) and steering wheel angle is
turned approximately 80 degrees with
the low beam on.

[Vehicle speed is between 6 mph
(10 km/h) to 56 mph (90 km/h)
and steering wheel angle is turned
approximately 35 degrees with the low
beam on.

[When the vehicle is in reverse with
one of the conditions above satisfied,
the light opposite to the direction the
steering wheel is turned will turn on.

5-50
Convenient features
- If the light switch is pushed away
when High Beam Assist is operating,
High Beam Assist will turn off.
- If the light switch is pulled towards
you when the high beam is off, the
high beam will turn on. When you let
go of the light switch, the lever will
move to the middle and the high beam
will turn off.
- If the light switch is pulled towards
you when the high beam is on by High
Beam Assist, and High Beam Assist
will turn off.
- If the light switch is placed to the
headlight position (
), High Beam
Assist will turn off and the low beam
will be on continuously.
When High Beam Assist is operating, the
high beam switches to low beam in the
following conditions.
- When the headlight of an on-coming
vehicle is detected.
- When the tail light of a vehicle in front
is detected.
- When the headlight or tail light of a
motorcycle or a bicycle is detected.
- When the surrounding ambient light is
bright enough that high beams are not
required.
- When streetlights or other lights are
detected.
- When the light switch is not in the
AUTO position.
- When High Beam Assist is off.
- When the vehicle speed is below 19
mph (30 km/h).
System malfunction and
limitations
System malfunction
OTM050218L
When High Beam Assist is not working
properly, the warning message will come
on for a few seconds. After the message
disappears, the master warning light
(
) will illuminate.
We recommend that you take your
vehicle to a HYUNDAI authorised
repairer and have the system checked.
CAUTION
The system may not operate normally if
any of the following conditions should
occur:
1. When the illumination from an
on-coming vehicle or a vehicle in
front is dim. Such examples may
include:

[When the headlights of an oncoming
vehicle or the tail lights of a vehicle
in front is covered with dust, snow,
or water

[When the headlights on an
RQFRPLQJYHKLFOHDUH2))EXWWKH
fog lights are ON)

5-51
05
2. When the front view camera is
adversely affected by an external
condition. Such examples may
include:

[When the vehicle’s headlights have
been damaged or not repaired
properly

[When the vehicle headlights are not
aimed properly

[When the vehicle is driven on a
narrow curved road or rough road

[When the vehicle is driven on an
uphill road or downhill road

[When only part of the vehicle in front
is visible on a crossroad or curved
road

[When there is a traffic light,
reflecting sign, flashing sign or mirror

[When the road conditions are bad
such as being wet or covered with
snow

[When a vehicle suddenly appears
from a curve

[When the vehicle is tilted from a flat
tyre or being towed

[ :KHQ/DQH.HHSLQJ$VVLVWV\VWHP
warning light illuminates

[When the light from the oncoming or
front vehicle is not detected because
of exhaust fume, smoke, fog, snow,
etc.

[When the front window is covered
with foreign matters such as ice,
dust, fog, or is damaged
3. When the forward visibility is poor.
Such examples may include:

[When the headlights of an oncoming
vehicle or a vehicle in front is not
detected due to poor outside
visibility (smog, smoke, dust, fog,
heavy rain, snow, etc.)

[When the windscreen visibility is
poor WARNING

[ 7KHIXQFWLRQPD\QRWZRUNDURXQG
seconds after starting the vehicle or
the initialization or rebooting of the
front view camera.

[ 'RQRWDWWHPSWWRGLVDVVHPEOH
the front view camera without the
assistance of a HYUNDAI authorised
repairer technician.
If the front view camera is removed
for any reason, the system may need
to be re-calibrated. We recommend
that the system be inspected by a
HYUNDAI authorised repairer.

[ ,IWKHZLQGVFUHHQRI\RXUYHKLFOH
is replaced, most likely the front
view camera will need to be
re-calibrated. If this occurs, have
your vehicle inspected and have the
system re-calibrated by a HYUNDAI
authorised repairer.

[ %HFDUHIXOWKDWZDWHUGRHVQ
TWJHWLQWR
front view camera unit and do not
remove or damage related parts of
High Beam Assist system.

[ 'RQRWSODFHREMHFWVRQWKHFUDVK
pad that reflect light such as mirrors,
white paper, etc. The system may
malfunction if sunlight is reflected.

[ $WWLPHV+LJK%HDP$VVLVWPD\
not work properly. The system is
for your convenience only. It is the
responsibility of the driver for safe
driving practices and always check
the road conditions for your safety.

[ :KHQWKHV\VWHPGRHVQRWRSHUDWH
normally, change the light position
manually between the high beam and
low beam.

5-52
Convenient features
INTERIOR LIGHTS
NOTICE
Do not use the interior lights for
extended periods when the engine is
turned off or the battery will discharge.
Interior light AUTO cut
The interior lights will automatically go
off approximately 20 minutes after the
engine is turned off and the doors are
closed. If a door is opened, the light will
go off 40 minutes after the engine is
turned off. If the doors are locked by the
remote key or smart key and the vehicle
enters the armed stage of the theft
alarm system, the lights will go off five
seconds later.
Front Room Lights
OBC3N050017
(1) Front Map Lamp
(2) Front Door Lamp
(3) Front Room Lamp ON
(4) Front Room Lamp OFF
)URQWPDSODPS
Press either of these lens to turn the
map lamp on or off. This light produces a
spot beam for convenient use as a map
lamp at night or as a personal lamp for
the driver and the front passenger.
)URQWGRRUODPS):
The front or rear
room lamps come on when the front
or rear doors are opened if the engine
is running or not. When doors are
unlocked by the remote key or smart
key, the front and rear lamps come on
for approximately 30 seconds as long as
any door is not opened. The front and
rear room lamps go out gradually after
approximately 30 seconds if the door is
closed. However, if the ignition switch
is in the ON position or all doors are
locked, the front and rear lamps will turn
off. If a door is opened with the ignition
switch in the ACC position or the OFF
position, the front and rear lamps stay
on for about 20 minutes.
)URQWURRPODPS
() : Press the button to turn ON the
room lamp for the front/rear
seats.
(
) : Press the button to turn OFF the
room lamp for the front/rear
seats.

5-64
Convenient features
System maintenance
Climate control air filter
OIK047401L
[A] : Outside air, [B] : Recirculated air
[C] : Climate control air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
This filter is installed behind the glove
box. It filters the dust or other pollutants
that enter the vehicle through the
heating and air conditioning system.
We recommend that the climate control
air filter be replaced by a HYUNDAI
authorised repairer according to the
maintenance schedule. If the vehicle is
being driven in severe conditions such
as dusty or rough roads, more frequent
climate control filter inspections and
changes are required.
If the air flow rate suddenly decreases,
we recommend the system be checked
at a HYUNDAI authorised repairer.
i Information

5-70
Convenient features
Temperature control
OBC3050111R
The temperature will increase by
pushing the switch to up.
The temperature will decrease by
pushing the switch to down.
The temperature will increase or
decrease by 0.5°C (1°F) for each
incremental location. When set to the
lowest temperature setting, the air
conditioning will operate continuously.
7HPSHUDWXUHFRQYHUVLRQ
If the battery has been discharged or
disconnected, the temperature mode
display will reset to Centigrade.
To change the temperature unit from °C
to °F or °F to °C :
- Automatic climate control system
Press the AUTO button for 3 seconds
whilst pressing the OFF button.
- Instrument cluster
Go to User Settings o Units o
Temperature Unit.
The temperature unit on both the cluster
LCD display and the climate control
screen will change.
Air intake control
OBC3050114R
This is used to select the outside (fresh)
air position or recirculated air position.
To change the air intake control position,
push the control button.
5HFLUFXODWHGDLUSRVLWLRQ
With the recirculated air
position selected, air from
the passenger
compartment will be
drawn through the heating
system and heated or
cooled according to the
function selected.
2XWVLGHIUHVKDLUSRVLWLRQ
With the outside (fresh) air
position selected, air
enters the vehicle from
outside and is heated or
cooled according to the
function selected.

5-75
05
System maintenance
Climate control air filter
OIK047401L
[A] : Outside air, [B] : Recirculated air
[C] : Climate control air filter, [D] : Blower
[E] : Evaporator core, [F] : Heater core
The climate control air filter installed
behind the glove box filters the dust
or other pollutants that come into the
vehicle from the outside through the
heating and air conditioning system. If
dust or other pollutants accumulate in
the filter over a period of time, the air
flow from the air vents may decrease,
resulting in moisture accumulation
on the inside of the windscreen even
when the outside (fresh) air position is
selected.
If this happens, we recommend that the
climate control air filter be replaced by a
HYUNDAI authorised repairer.
i Information

5-77
05
WARNING
Windscreen heating
Do not use the
or position
during cooling operation in extremely
humid weather. The difference
between the temperature of the
outside air and that of the windscreen
could cause the outer surface of the
windscreen to fog up, causing loss of
visibility. In this case, set the mode
selection knob or button to the

position and fan speed control knob or
button to lower speed.

[ )RUPD[LPXPGHIURVWSHUIRUPDQFH
set the temperature control knob
to the highest temperature setting
(rotated all the way to the right) and
the fan speed control to the highest
setting.

[ ,IZDUPDLUWRWKHIORRULVGHVLUHG
whilst defrosting or defogging, set the
mode to the floor-defrost position.

[ %HIRUHGULYLQJFOHDUDOOVQRZDQGLFH
from the windscreen, rear window,
outside rear view mirrors, and all side
windows.

[ &OHDUDOOVQRZDQGLFHIURPWKH
bonnet and air inlet in the cowl grill
to improve heater and defroster
efficiency and to reduce the
probability of fogging up inside of the
windscreen.
i Information
,IWKHHQJLQHWHPSHUDWXUHLVVWLOOFROGDIWHU
starting, then a brief engine warm up
period may be required for the vented air
flow to become warm or hot.
Manual climate control system
To defog inside windscreen
OBC3050118
1. Select any fan speed except
"0"position.
2. Select the desired temperature.
3. Select the
or position.
4. The outside (fresh) air will be selected
automatically. Additionally, the
air conditioning (if equipped) will
automatically operate if the mode is
selected to the
position.
If the air conditioning and outside
(fresh) air position are not selected
automatically, press the corresponding
button manually.
WINDSCREEN DEFROSTING AND DEFOGGING

5-80
Convenient features
7RFDQFHORUUHVHWWKH$XWR'HIRJJLQJ
System
Press the front windscreen defroster
button for 3 seconds when the ignition
switch is in the ON position.
When the Auto Defogging System is
cancelled, defrost button indicator will
blink 3 times.
When the Auto Defogging System is
reset, defrost button indicator will blink
6 times without a signal.
i Information
:KHQWKHDLUFRQGLWLRQLQJLVWXUQHGRQE\
Auto defogging system, if you try to turn
off the air conditioning, the indicator will
blink 3 times and the air conditioning will
not be turned off.
7RPDLQWDLQWKHHIIHFWLYHQHVVDQG
HIILFLHQF\RIWKH$XWR'HIRJJLQJ6\VWHP
GRQRWVHOHFW5HFLUFXODWLRQPRGHZKLOVW
the system is operating.
:KHQWKH$XWR'HIRJJLQJ6\VWHPLV
operating, the blower speed adjustment
knob, the temperature adjustment knob,
and the air intake control button are all
disabled.
NOTICE
Do not remove the sensor cover
located at the top of the driver side
windscreen glass.
Damage to system parts could occur
and may not be covered by your vehicle
warranty.
Defroster
NOTICE
To prevent damage to the conductors
bonded to the inside surface of the rear
window, never use sharp instruments
or window cleaners containing
abrasives to clean the window.
i Information
,I\RXZDQWWRGHIURVWDQGGHIRJWKH
IURQWZLQGVFUHHQUHIHUWR