reset INFINITI EX 2013 Quick Reference Guide

3
Loose Fuel Cap
A LOOSE FUEL CAP warning message will appear in
the dot matrix liquid crystal display

01 when the
fuel-filler cap is not tightened correctly.

To tighten, turn the cap clockwise until a single click
is heard.

The warning message will disappear when the vehicle
detects the fuel-filler cap is properly tightened and the
reset button

02 is pressed.

If the cap is not properly tightened, the Malfunction
Indicator Light
may illuminate.
For more information, refer to the “Instruments and controls (section 2)” and
the “Pre-driving checks and adjustments (section 3)” of your Owner’s Manual.
Tire Pressure Monitoring System (TPMS)

A ChECk tIrE PrESSUrE warning message will
appear in the dot matrix liquid crystal display

01
and the low tire pressure warning light
02 will

illuminate when one or more tires are low on
pressure and air is needed.
• The tire pressures should be checked when the
tires are cold. The tires are considered cold after
the vehicle has been parked for 3 hours or more or
driven less than 1 mile (1.6km) at moderate speeds.

After tire pressures are adjusted, drive the vehicle at
speeds above 16 MPH (25km/h). The ChECk tIrE
PrESSUrE warning message and the low tire pressure
warning light will disappear.

when the low tire pressure warning light flashes for 1 minute and then remains on, the TPMS
is not functioning properly. Have the system checked by an INFINITI retailer.

Tire pressure rises and falls depending on the heat caused by the vehicle’s operation and the
outside temperature. Low outside temperature can lower the temperature of the air inside the
tire, which can cause a lower tire inflation pressure. This may cause the low tire pressure
warning light to illuminate. If the warning light illuminates in low ambient temperature,
check the tire pressure in your tires.
• Check the tire pressure (including the spare tire) often and always prior to long distance trips.

The Tire and Loading Information label contains valuable information. Please refer to section 9,
“Technical and consumer information”, in your Owner’s Manual for the location of the Tire and
Loading Information label.
For more information, refer to the “Instruments and controls (section 2)”, the “Starting and driving (section 5)” and the
“Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
essential information
01
01
02
02

11
FM/AM/SiriusXM™* Satellite Radio with CD/DVD Player (with Navigation System -
if so equipped)
01 VOLUME/ON•OFF CONTROL KNOB


Press the VOL/ON•OFF control knob to turn the system on or off. Turn the knob right or left
to increase or decrease the volume.
02 SEEK•CAT AND TRACK BUTTONS


To scan quickly through each broadcasting station, press the SEEK•CAT button or the
trACk button to stop at the previous or next broadcast station.

For SiriusXM™ satellite radio, press the SEEK•CAT button or the trACk button to switch to
the first channel of the previous or next category.

Press the SEEK•CAT button or the trACk button to change tracks on a cD.

Press and hold the SEEK•CAT button or the trACk button to fast forward or rewind a
track on a cD.
03 tUNE/FOLDEr/AUDIO CONtrOL kNOB


To manually tune the radio, turn the tUNE/FOLDEr/AUDIO knob left or right.
04 S
tA tION PrESEt BUtt ONS

Twelve stations can be set for the FM band, six for the AM band and eighteen for
SiriusXM satellite radio.


To store a station in a preset, you must first select a radio band by pressing the
AM•FM/SAT button
05 , then tune to the desired AM, FM or SiriusXM satellite station.


Then press and hold the desired station preset button (1-6) until the preset number
is updated on the display and the sound is briefly muted. The channel indicator will then
display and the sound will resume. Programming is now complete.

To retrieve a previously set station, select the radio band where the preset was stored, then
press the corresponding station select button (1-6).
*SiriusXM™ Satellite Radio is only available on vehicles equipped with optional SiriusXM™ satellite subscription service.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4)” of your Owner’s Manual.
05
010203
04

12
first drive features
USB/iPod® Interface (models with Navigation System - if so equipped)
The USB jack
01 is located in the center console under

the arm rest.

when a compatible USB memory device or iPod®
is plugged into the USB jack, compatible audio
and video files stored on the device can be
played through the vehicle’s audio system
and front display.
For more information, refer to the “Monitor, climate, audio, phone
and voice recognition systems (section 4)” of your Owner’s Manual.
Conventional (Fixed Speed) Cruise Control

The cruise control system enables you to set a constant
cruising speed once the vehicle has reached 25 mph.

The system will automatically maintain the set speed
until you tap the brake pedal, accelerate, cancel or
turn the system off.

To activate the cruise control, push the ON/OFF
switch

01 . The CrUISE indicator light in the
instrument panel will illuminate.

To set cruising speed, accelerate the vehicle to the desired speed, push the COAS t/SEt switch


02 and release. The CrUISE SEt
indicator light
in the instrument panel will illuminate.

Take your foot off the accelerator pedal. Your vehicle will maintain the set speed.

To reset at a faster cruising speed, push and hold the ACCEL/rES switch
03 . when the

vehicle attains the desired speed, release the switch.

To reset at a slower cruising speed, push and hold the COAS t/SEt switch
02 . Release the

switch when the vehicle slows to the desired speed.

To cancel the preset speed, tap the brake pedal or push the CANCEL switch
04 .

To turn off cruise control, push the ON/OFF switch
01 . Both the CrUISE indicator light and

the SEt indicator light
in the instrument panel will turn off.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
04
03
02
01
01

13
Intelligent Cruise Control (ICC) System (if so equipped)
VEHIcLE-TO-VEHIcLE DISTANcE cONTROL MODE


To set Vehicle-To-Vehicle Distance c ontrol mode,
press the CrUISE ON/OFF button
01 for less
than 1.5 seconds. The CrUISE indicator light
02
will illuminate.

Accelerate to the desired speed.

Push down on the COAS t/SEt switch
03 and release
it. cruise control will be set to the desired speed.

Press the distance button
04 repeatedly to change
the set distance between long, middle, and short.

when a vehicle is not detected ahead of you in the
lane, the set distance and set vehicle speed indicator
lights will illuminate

05 in set mode.

when a vehicle is detected ahead of you in the lane,
the vehicle ahead detection, set distance, and set
vehicle speed indicator lights will illuminate

06 in set mode.

To reset at a faster cruising speed, push up and hold the ACCEL/rES
switch

07 . w
hen the vehicle attains the desired speed, release
the switch.

To reset at a slower cruising speed, push down and hold the COAS t/SEt switch
03 . Release

the switch when the vehicle slows to the desired speed.

To cancel the preset speed, push the CANCEL switch
08 or tap the brake pedal
. The set
vehicle speed indicator
05 will go out.

To turn off cruise control, press the CrUISE ON/OFF button
01 . The
CrUISE indicator light

02 , in the instrument panel, will turn off.
To set conventional (fixed speed) cruise control mode:

while cruise control is off, press the CrUISE ON/OFF
button
01 and hold it down for more
than 1.5 seconds. The CrUISE indicator light will illuminate.

Accelerate to the desired speed.

Push down on the COAS t/SEt switch and release it. The SEt indicator light will illuminate.
c ruise control should be set to the desired speed.
To switch between the two cruise control modes:

when one of the two cruise modes is in use, you must turn the system off, and then turn it on
again to select the other cruise control mode.
For more information, refer to the “Starting and driving (section 5)” of your Owner’s Manual.
08
07
03
01
04
0205
06

Trip Computer
when the
button
01 is pressed, the following
modes will appear on the dot matrix liquid crystal
display

02 :
• MPG – Displays the current and average fuel
consumption since the last reset.
• MPG/MPh – Displays the average fuel consumption
and speed since the last reset.
• tIME/MILES – Displays the elapsed time and total
distance the vehicle has been driven since the
last reset.
• rANGE – Displays the estimated distance to empty
(dte) the vehicle can be driven before refueling.
• OUtSIDE tEMP – Displays the exterior air
temperature including a low temperature warning feature.
• SEttING – Allows you to set reminders for alerts and maintenance intervals or change the
language and units used in the system.
— Press the

button
03 to cycle through the various setting modes.

— Press the

button
01 to choose the selected menu.

• WArNING – If there are any.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual.
system guide
15
01
03
02
Bluetooth® Hands-free Phone System (if so equipped)

with an overhead microphone and sound
transmitted through the audio system speakers,
the Bluetooth
® Hands-free Phone System utilizes
Bluetooth wireless technology and voice recognition
to provide hands-free cellular phone communication.

Bluetooth Streaming Audio (models with Navigation
System only) allows you to use a compatible Bluetooth
phone to play audio files on your device. Your
compatible cellular phone can be connected to the
vehicle’s audio system allowing audio files to play
through the vehicle’s speakers.

A cellular telephone should not be used while driving
so full attention may be given to vehicle operation.*
Bluetooth® Controls
*Some jurisdictions prohibit the use of cellular telephones while driving.