flat tire INFINITI FX 2010 Owner's Manual

CHANGING WHEELS AND TIRES
Tire rotation
INFINITI recommends rotating the tires
every 7,500 miles (12,000 km). (See
“FLAT TIRE” in the “6. In case of emer-
gency” section for tire replacing proce-
dures.)
As soon as possible, tighten the wheel
nuts to the specified torque with a torque
wrench.Wheel nut tightening torque:
80 ft-lb (108 N·m)
The wheel nuts must be kept tightened to
the specification at all times. It is recom-
mended that wheel nuts be tightened to
the specification at each tire rotation in-
terval.
WARNING
●After rotating the tires, check and ad-
just the tire pressure.
●Retighten the wheel nuts when the
vehicle has been driven for 600 miles
(1,000 km) (also in cases of a flat tire,
etc.).
●Do not include the T-type spare tire or
any other small size spare tire in the
tire rotation.
●For additional information regarding
tires, refer to “Important Tire Safety
Information” (US) or “Tire Safety In-
formation” (Canada) in the Warranty
Information Booklet. 1. Wear indicator
2. Wear indicator location mark
Tire wear and damage
WARNING
●Tires should be periodically in-
spected for wear, cracking, bulging or
objects caught in the tread. If exces-
sive wear, cracks, bulging or deep
cuts are found, the tire(s) should be
replaced.
SDI1662SDI1663
8-36Maintenance and do-it-yourself
—
—
08/03/09—pattie


●For additional information regarding tires,
refer to “Important Tire Safety Information”
(US) or “Tire Safety Information” (Canada) in
the Warranty Information Booklet.
All-Wheel Drive (AWD) models
CAUTION
● Always use tires of the same type, size,
brand, construction (bias, bias-belted or ra-
dial), and tread pattern on all four wheels.
Failure to do so may result in a circumference
difference between tires on the front and
rear axles which will cause excessive tire
wear and may damage the transmission,
transfer case and differential gears.
● ONLY use spare tires specified for the AWD
model.
If excessive tire wear is found, it is recom-
mended that all four tires be replaced with tires
of the same size, brand, construction and tread
pattern. The tire pressure and wheel alignment
should also be checked and corrected as nec-
essary. Contact an INFINITI retailer.
Wheel balance
Unbalanced wheels may affect vehicle handling
and tire life. Even with regular use, wheels can
get out of balance. Therefore, they should be
balanced as required.
Wheel balance service should be performed with
the wheels off the vehicle. Spin balancing the
wheels on the vehicle could lead to mechanical
damage.
For additional information regarding tires, refer
to “Important Tire Safety Information” (US) or
“Tire Safety Information” (Canada) in the
INFINITI Warranty Information Booklet.
Care of wheels
See “CLEANING EXTERIOR” in the “7. Appear-
ance and care” section for details about care of
the wheels.
Spare tire (TEMPORARY USE ONLY
(T-type) spare tire)
When a spare tire is mounted (TEMPORARY USE
ONLY or conventional), the TPMS will not func-
tion.
Observe the following precautions if the T-type
spare tire must be used, otherwise your vehicle
could be damaged or involved in an accident.
WARNING
● The T-type spare tire should be used for
emergency use. It should be replaced with
the standard tire at the first opportunity to
avoid possible tire or differential damage.
● Drive carefully while the TEMPORARY USE
ONLY spare tire is installed. Avoid sharp
turns and abrupt braking while driving.
● Periodically check spare tire inflation pres-
sure. Always keep the pressure of the TEM-
PORARY USE ONLY spare tire at 60 psi (420
kPa, 4.2 bar). Always keep the pressure of
the full size spare tire (if so equipped) at the
recommended pressure for standard tires,
as indicated on the Tire and Loading Infor-
mation label. For Tire and Loading Informa-
tion label location, see “Tire and Loading
Information label” in the index of this
manual.
● With the TEMPORARY USE ONLY spare tire
installed do not drive your vehicle at speeds
faster than 50 MPH (80 km/h).
● When driving on roads covered with snow or
ice, the TEMPORARY USE ONLY spare tire
should be used on the front wheels and origi-
nal tire used on the rear wheels (drive
wheels). Use tire chains only on the two rear
original tires.
8-38Maintenance and do-it-yourself
—
—
08/03/09—pattie


9 Technical and consumer information
Capacities and recommended fuel/lubricants........ 9-2
Fuel recommendation ........................... 9-4
Engine oil and oil filter recommendation ......... 9-6
Air conditioning system refrigerant and
lubricant recommendations ..................... 9-7
Specifications ..................................... 9-8
Engine ........................................ 9-8
Wheels and tires ............................... 9-9
Dimensions ................................... 9-10
When traveling or registering your vehicle in
another country .................................. 9-10
Vehicle identification .............................. 9-11
Vehicle Identification Number (VIN) plate .........9-11
Vehicle identification number (chassis
number) ....................................... 9-11
Engine serial number .......................... 9-12
F.M.V.S.S./C.M.V.S.S. certification label .........9-12
Emission control information label ..............9-12
Tire and loading information label ..............9-13
Air conditioner specification label ...............9-13
Installing front license plate .......................9-14
Vehicle loading information ........................9-15
Terms ......................................... 9-15Vehicle load capacity
.......................... 9-16
Securing the load ............................. 9-17
Loading tips .................................. 9-18
Measurement of weights ....................... 9-19
Towing a trailer .................................. 9-19
Maximum load limits .......................... 9-19
Maximum gross vehicle weight (GVW)/
maximum gross axle weight (GAW) .............9-21
Towing load/specification ......................9-23
Towing safety ................................. 9-23
Flat towing ................................... 9-27
Uniform tire quality grading .......................9-28
Treadwear .................................... 9-28
Traction AA, A, B and C ........................ 9-28
Temperature A, B and C ....................... 9-28
Emission control system warranty .................9-29
Reporting

safety defects (US only) .................9-29
Readiness for Inspection/Maintenance (I/M) test ....9-30
Event Data Recorders (EDR) .......................9-31
Owner’s Manual/Service Manual order
information ...................................... 9-32
In the event of a collision ......................9-32
—
—
08/03/09—pattie


6. Insert a flat-blade screwdriver into thegrommet hole to add 90° turn onto the
part
D.
7. Insert a J-nut into the license plate bracket before placing the license plate bracket
on the fascia.
8. Install the license plate bracket with screws.
9. Install the license plate with bolts that are no longer than 0.55 in (14 mm).
WARNING
●It is extremely dangerous to ride in a
cargo area inside the vehicle. In a col-
lision, people riding in these areas
are more likely to be seriously injured
or killed.
●Do not allow people to ride in any area
of vehicle that is not equipped with
seats and seat belts.
●Be sure everyone in your vehicle is in
a seat and using a seat belt properly.
TERMS
It is important to familiarize yourself
with the following terms before loading
your vehicle:
●Curb Weight (actual weight of your
vehicle) - vehicle weight including:
standard and optional equipment, flu-
ids, emergency tools, and spare tire
assembly. This weight does not
include
passengers and cargo. ●
GVW (Gross Vehicle Weight) - curb
weight plus the combined weight of
passengers and cargo.
●GVWR (Gross Vehicle Weight Rating) -
maximum total combined weight of
the unloaded vehicle, passengers,
luggage, hitch, trailer tongue load
and any other optional equipment.
This information is located on the
F.M.V.S.S./C.M.V.S.S. label.
●GAWR (Gross Axle Weight Rating) -
maximum weight (load) limit specified
for the front or rear axle. This infor-
mation is located on the
F.M.V.S.S./C.M.V.S.S. label.
●GCWR (Gross Combined Weight Rat-
ing) - The maximum total weight rat-
ing of the vehicle, passengers, cargo,
and trailer.
●Vehicle Capacity Weight, Load limit,
Total load capacity - maximum total
weight limit specified of the load
(passengers and cargo) for the ve-
hicle. This is the maximum combined
VEHICLE LOADING INFORMATION
Technical and consumer information9-15
—
—
08/03/09—pattie


Steps for determining correct load
limit
1.Locate the statement “The combined
weight of occupants and cargo should
never exceed XXX kg or XXX lbs” on
your vehicle’s placard.
2.Determine the combined weight of
the driver and passengers that will be
riding in your vehicle.
3.Subtract the combined weight of the
driver and passengers from XXX kg or
XXX lbs.
4.The resulting figure equals the avail-
able amount of cargo and luggage
load capacity. For example, if the XXX
amount equals 1400 lbs. and there
will be five 150 lb. passengers in your
vehicle, the amount of available
cargo and luggage load capacity is
650 lbs. (1400 750 (5 x 150) = 650
lbs) or (640 340 (5 x 70) = 300 kg.)
5.Determine the combined weight of
luggage and cargo being loaded on
the vehicle. That weight may not
safely exceed the available cargo and
luggage load capacity calculated in
Step 4.
6.If your vehicle will be towing a trailer,
load from your trailer will be trans-
ferred to your vehicle. Consult this
manual to determine how this re-
duces the available cargo and lug-
gage load capacity of your vehicle.
Before driving a loaded vehicle, confirm
that you do not exceed the Gross Vehicle
Weight Rating (GVWR) or the Gross Axle
Weight Rating (GAWR) for your vehicle.
(See “MEASUREMENT OF WEIGHTS” later
in this section.)
Also check tires for proper inflation pres-
sures. See the Tire and Loading Informa-
tion label.
SECURING THE LOAD
There are tie down hooks located in the cargo
area as shown. The tie down hooks can be used
to secure cargo with ropes or other types of
straps.
Do not apply a total load of more than 22 lb.
(98 N) to a single hook when securing cargo.
WARNING
● Properly secure all cargo with ropes or
straps to help prevent it from sliding or shift-
ing. Do not place cargo higher than the seat-
backs. In a sudden stop or collision, unse-
cured cargo could cause personal injury.
SIC3849
Technical and consumer information9-17
—
—
08/03/09—tbrooks


●The diameter of the threaded shank of the
hitch ball must be matched to the ball mount
hole diameter. The hitch ball shank should
be no more than 1/16 smaller than the hole
in the ball mount.
● The threaded shank of the hitch ball must be
long enough to be properly secured to the
ball mount. There should be at least 2
threads showing beyond the lock washer
and nut.
Sway control device
Sudden maneuvers, wind gusts and buffeting
caused by other vehicles can affect trailer han-
dling. Sway control devices may be used to help
control these affects. If you choose to use one,
contact a reputable trailer hitch supplier to
make sure the sway control device will work
with the vehicle, hitch, trailer and the trailer’s
brake system. Follow the instructions provided
by the manufacturer for installing and using the
sway control device.
Class I hitch
Class I trailer hitch equipment (receiver, ball
mount and hitch ball) can be used to tow
trailers of a maximum weight of 2,000 lb
(907 kg).
Class II hitch
Class II trailer hitch equipment (receiver, ball
mount and hitch ball) can be used to tow
trailers of a maximum weight of 3,500 lb
(1,588 kg).
CAUTION
● Special hitches which include frame rein-
forcements are required for towing above
2,000 lb (907 kg). Suitable genuine INFINITI
hitches for pickup trucks and sport utility
vehicles are available at an INFINITI retailer.
● The hitch should not be attached to or affect
the operation of the impact-absorbing
bumper.
● Do not use axle-mounted hitches.
● Do not modify the vehicle exhaust system,
brake system, etc. to install a trailer hitch.
● To reduce the possibility of additional dam-
age if your vehicle is struck from the rear,
where practical, remove the hitch and/or re-
ceiver when not in use. After the hitch is
removed, seal the bolt holes to prevent ex-
haust fumes, water or dust from entering the
passenger compartment.
● Regularly check that all trailer hitch mount-
ing bolts are securely mounted.
Tire pressures
●When towing a trailer, inflate the ve-
hicle tires to the recommended cold
tire pressure indicated on the Tire and
Loading Information label.
●Trailer tire condition, size, load rating
and proper inflation pressure should
be in accordance with the trailer and
tire manufacturers’ specifications.
Safety chains
Always use a suitable chain between your ve-
hicle and the trailer. The safety chains should
be crossed and should be attached to the hitch,
not to the vehicle bumper or axle. The safety
chains can be attached to the bumper if the
hitch ball is mounted to the bumper. Be sure to
leave enough slack in the chains to permit
turning corners.
9-24Technical and consumer information
—
—
08/03/09—pattie


DOT (Department Of Transportation) Quality
Grades: All passenger car tires must conform to
federal safety requirements in addition to these
grades.
Quality grades can be found where applicable
on the tire sidewall between tread shoulder and
maximum section width. For example:
Treadwear 200 Traction AA Temperature A
TREADWEAR
The treadwear grade is a comparative rating
based on the wear rate of the tire when tested
under controlled conditions on a specified gov-
ernment test course. For example, a tire graded
150 would wear one and one-half (1 1/2) times
as well on the government course as a tire
graded 100. The relative performance of tires
depends upon actual conditions of their use,
however, and may depart significantly from the
norm due to variations in driving habits, service
practices and differences in road characteristics
and climate.
TRACTION AA, A, B AND C
The traction grades, from highest to lowest, are
AA, A, B and C. Those grades represent the
tire’s ability to stop on wet pavement as mea-
sured under controlled conditions on specifiedgovernment test surfaces of asphalt and con-
crete. A tire marked C may have poor traction
performance.
WARNING
The traction grade assigned to this tire is based
on straight-ahead braking traction tests, and
does not include acceleration, cornering, hy-
droplaning, or peak traction characteristics.
TEMPERATURE A, B AND C
The temperature grades A (the highest), B, and
C, representing the tire’s resistance to the
generation of heat and its ability to dissipate
heat when tested under controlled conditions
on a specified indoor laboratory test wheel.
Sustained high temperature can cause the ma-
terial of the tire to degenerate and reduce tire
life, and excessive temperature can lead to
sudden tire failure. The grade C corresponds to
a level of performance which all passenger car
tires must meet under the Federal Motor Vehicle
Safety Standard No. 109. Grades B and A rep-
resent higher levels of performance on the
laboratory test wheel than the minimum re-
quired by law.
WARNING
The temperature grade for this tire is estab-
lished for a tire that is properly inflated and not
overloaded. Excessive speed, under-inflation,
or excessive loading, either separately or in
combination, can cause heat build-up and pos-
sible tire failure.
UNIFORM TIRE QUALITY GRADING
9-28Technical and consumer information
—
—
08/03/09—pattie


Checking engine coolant level......8-9
Checking engine oil level .........8-10
Engine block heater ............5-81
Engine compartment check locations . . . 8-6
Engine cooling system ...........8-9
Engine oil .................. 8-10
Engine oil and oil filter
recommendation ..............9-6
Engine oil replacement indicator .....2-25
Engine oil viscosity .............9-6
Engine serial number ...........9-12
Engine specifications ............9-8
Engine start operation indicator .....2-23
If your vehicle overheats .........6-10
Starting the engine ............5-12
Engine coolant temperature gauge ......2-7
Entry/exit function, Automatic drive
positioner ................... .3-25
Event Data Recorders (EDR) ..........9-31
Exhaust gas (carbon monoxide) ........5-2
F
F.M.V.S.S./C.M.V.S.S. certification label . . .9-12
Filter Air cleaner housing filter .........8-19
Changing engine oil and filter ......8-11
Flashers
(See hazard warning flasher switch) .....2-40
Flat tire ..................... .6-2
Flat towing .................. .9-27
Floor mat cleaning ............... .7-5
Fluid Automatic transmission fluid (ATF) . . . .8-13
Brake fluid ................. 8-14Capacities and recommended fuel/
lubricants
..................9-2
Engine coolant ...............8-9
Engine oil .................. 8-10
Power steering fluid ............8-13
Window washer fluid ...........8-14
FM-AM-SAT radio with Compact Disc (CD)
player ..................... .4-61
Fog light switch ............... .2-40
Forward Collision Warning (FCW) system . . .5-61
Front passenger air bag and status light . .1-47
Front power seat adjustment ..........1-2
Front seat, Front seat adjustment .......1-2
Fuel Capacities and recommended fuel/
lubricants .................. .9-2
Fuel

economy ............... 5-68
Fuel economy information (display) ....4-9
Fuel octane rating .............9-4
Fuel recommendation ...........9-4
Fuel-filler cap ................ 3-18
Fuel-filler door ............... 3-18
Gauge ....................2-8
Fuses ..................... .8-22
Fusible links ................. .8-22
G
Garage door opener, HomeLink Universal
Transceiver .................. .2-60
Gascap .................... .3-18
Gauge ...................... .2-5
Gauge Engine coolant temperature gauge . . . .2-7
Fuel gauge ..................2-8 Odometer
..................2-6
Speedometer ................2-6
Tachometer .................2-7
Trip computer ............... 2-27
General maintenance ..............8-2
Glove box ................... .2-48
H
Hands-free phone system, Bluetooth
(with navigation system) ...........4-104
Hands-free phone system, Bluetooth
(without navigation system) .........4-115
Hazard warning flasher switch . . . . . . . .2-40
Head restraints ................. .1-6
Headlights Aiming control (See adaptive front
lighting system (AFS)) ...........2-38
Bulb replacement ............. 8-26
Headlight switch .............. 2-36
Xenon headlights ............. 2-35
Headphones (See INFINITI mobile
entertainment system) ........4-94 , 4-102
Heater Automatic climate control .........4-40
Engine block heater ............5-81
HomeLink Universal Transceiver . . . . . .2-60
Hood release ................. .3-16
Hook Coat
hooks................ .2-49
Luggage hook ............... 2-50
Horn ...................... .2-41
10-3
—
—
10/19/09—tbrooks


Sun visors................... .3-21
Sunglasses holder .............. .2-47
Supplemental air bag warning labels . . . .1-53
Supplemental air bag warning light . .1-53 , 2-17
Supplemental restraint system ........1-40
Supplemental restraint system, Precautions
on supplemental restraint system ......1-40
Switch Autolight switch ............. .2-36
Continuous Damping Control mode
select switch ................ 2-44
Fog light switch .............. 2-40
Forward Collision Warning (FCW)
switch ................... 2-43
Hazard warning flasher switch ......2-40
Headlight switch .............. 2-36
Ignition switch automatic transmission
models ................... 5-13
Intelligent Brake Assist (IBA) OFF
switch ................... 2-44
Lane departure warning (LDW)
system ................... 2-42
Power door lock switch ...........3-5
Rear window and outside mirror
defroster switch .............. 2-35
Snow mode switch ............2-43
Turn signal switch ............. 2-39
Vehicle dynamic control (VDC) off
switch .................... 2-45
T
Tachometer ................... .2-7
Temperature gauge, Engine coolant
temperature gauge .............. .2-7Theft (INFINITI Vehicle Immobilizer System),
Engine start
.................. .2-31
Thigh extension ................ .1-4
Three-way catalyst ............... .5-2
Tilt/telescopic steering .............3-19
Tire pressure, Low tire pressure warning
light ...................... .2-15
Tire, Tire replacement indicator ........2-25
Tires Flat tire ................... .6-2
Low tire pressure warning system ....5-3
Spare tire ................. 8-38
Tire and Loading information label . . . 8-30
Tire chains ................. 8-35
Tire dressing ................7-4
Tire pressure ................ 8-28
Tire pressure monitoring system
(TPMS) ....................
5-3
Tire rotation ................ 8-36
Types of tires ............... 8-34
Uniform tire quality grading .......9-28
Wheel/tire size ...............9-9
Wheels and tires ............. 8-28
Tonneau cover (see cargo cover) .......2-51
Top tether strap child restraints .......1-24
Touch screen system ..............4-4
Towing Flat towing ................ .9-27
Tow truck towing .............. 6-11
Towing a trailer .............. 9-19
Towing safety ............... 9-23
TPMS, Tire pressure monitoring system . . . .5-3
TPMS, Tire pressure warning system .....6-2
Trailer towing ................. .9-19Transceiver, HomeLink
Universal
Transceiver .................. .2-60
Transmission Automatic transmission fluid (ATF) . . . .8-13
Driving with automatic transmission . . . 5-13
Transmission selector lever lock
release ................... 5-16
Transmitter
(See remote keyless entry system) ......3-13
Traveling or registering your vehicle in
another country ................ .9-10
Trip computer ................. .2-27
Trip odometer ................. .2-27
Turn signal switch .............. .2-39
U
Underbody cleaning .............. .7-3
Uniform tire quality grading .........9-28
V
Vanity mirror ................. .3-24
Vanity mirror lights ............. .2-59
Variable voltage control system . . .....8-17
Vehicle Dimensions ................ .9-10
Recovery (freeing a stuck vehicle) . . . . 6-14
Vehicle dynamic control (VDC) off
switch .................... 2-45
Vehicle dynamic control (VDC)
system ................... 5-77
Vehicle information and settings
(display) ...................

4-7
10-7
—
—
10/19/09—tbrooks