low beam INFINITI FX35 2005 User Guide
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 1290 of 4731
UNIFIED METER AND A/C AMP DI-29
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
FA I L - S A F E
Solution When Communication Error Between the Unified Meter & A/C Amp. and the Combi-
nation Meter
CAN Communication System DescriptionAKS007Z1
CAN (Controller Area Network) is a serial communication line for real time application. It is an on-vehicle mul-
tiplex communication line with high data communication speed and excellent error detection ability. Many elec-
tronic control units are equipped onto a vehicle, and each control unit shares information and links with other
control units during operation (not independent). In CAN communication, control units are connected with 2
communication lines (CAN H line, CAN L line) allowing a high rate of information transmission with less wiring.
Each control unit transmits/receives data but selectively reads required data only.
CAN Communication UnitAKS007YX
Refer to LAN-30, "CAN Communication Unit" in “LAN SYSTEM”.
Function Specifications
Speedometer Return to zero when discontinuing communication or receiving
irregular data.
Tachometer Reset to zero by suspending communication.
Fuel gauge
Water temperature gauge
Illumination control Combination meter illumination When suspending communication, change to nighttime mode.
Odo/trip meter Integrate in response to 8-pulse input.
A/T position indicator The display turns off by suspending communication.
Warning buzzer The warning buzzer turns off by suspending communication.
Warning lamp/indicator lamp ABS warning lamp
The lamp turns on by suspending communication.
VDC OFF indicator
SLIP indicator
Brake warning lamp
Door warning lamp
The lamp turns off by suspending communication.
Low tire pressure warning lamp
SET indicator lamp
CRUISE indicator lamp
AWD warning lamp
ICC warning lamp
A/T CHECK warning lamp
Oil pressure warning lamp
Snow mode indicator lamp
Turn signal indicator
Malfunction indicator lamp
High beam indicator
Page 1294 of 4731
UNIFIED METER AND A/C AMP DI-33
C
D E
F
G H
I
J
L
M A
B
DI
Revision: 2005 July 2005 FX
4. Touch “START”.
5. Touch “RECORD” while monitoring, then the status of the moni- tored item can be recorded. To stop recording, touch “STOP”.
Display Item List
SKIA4957E
Display item [Unit] MAIN
SIGNALS SELECTION
FROM MENU Contents
SPEED METER [km/h] or [mph] X X This is the angle correction value after the speed signal from the
ABS actuator and electric unit (control unit) is converted into the
vehicle speed.
SPEED OUTPUT [km/h] or [mph] X X This is the angle correction value before the speed signal from
the ABS actuator and electric unit (control unit) is converted into
the vehicle speed.
TACHO METER [rpm] X X This is the converted value for the engine speed signal from the
ECM.
W TEMP METER [ °C] or [ °F] X X This is the converted value for the engine coolant temperature
signal from the ECM.
FUEL METER [lit.] X X This is the processed value for the signal (resistance value)
from the fuel gauge.
DISTANCE [km] or [mile] X X This is the calculated value for the speed signal from the ABS
actuator and electric unit (control unit), the signal (resistance
signal) from the fuel gauge and fuel consumption signal from
ECM.
FUEL W/L [ON/OFF] X X Indicates [ON/OFF] condition of low-fuel warning lamp.
MIL [ON/OFF] X Indicates [ON/OFF] condition of malfunction indicator lamp.
AIR PRES W/L [ON/OFF] X Indicates [ON/OFF] condition of low tire pressure warning lamp.
SEAT BELT W/L [ON/OFF] X Indicates [ON/OFF] condition of seat belt warning lamp.
BUZZER [ON/OFF] X X Indicates [ON/OFF] condition of buzzer.
DOOR W/L [ON/OFF] X Indicates [ON/OFF] condition of door warning lamp.
HI-BEAM IND [ON/OFF] X Indicates [ON/OFF] condition of high beam indicator.
TURN IND [ON/OFF] X Indicates [ON/OFF] condition of turn indicator.
OIL W/L [ON/OFF] X Indicates [ON/OFF] condition of oil pressure warning lamp.
VDC/TCS IND [ON/OFF] X Indicates [ON/OFF] condition of VDC OFF indicator lamp.
ABS W/L [ON/OFF] X Indicates [ON/OFF] condition of ABS warning lamp.
SLIP IND [ON/OFF] X Indicates [ON/OFF] condition of SLIP indicator lamp.
BRAKE W/L [ON/OFF] X Indicates [ON/OFF] condition of brake warning lamp.*
KEY G W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (green).
KEY R W/L [ON/OFF] X Indicates [ON/OFF] condition of key warning lamp (red).
KEY KNOB W/L [ON/OFF] X Indicates [ON/OFF] condition of key knob warning lamp.
M RANGE SW [ON/OFF] X X Indicates [ON/OFF] condition of manual mode range switch.
NM RANGE SW [ON/OFF] X X Indicates [ON/OFF] condition of except for manual mode range
switch.
AT SFT UP SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift-up switch.
AT SFT DWN SW [ON/OFF] X X Indicates [ON/OFF] condition of A/T shift-down switch.
Page 2961 of 4731
![INFINITI FX35 2005 User Guide EM-126
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
10. Remove pilot converter using the pilot bushing puller [SST] as
necessary.
11. Remove rear oil seal retainer.
Remove by inserting a scr](/img/42/57020/w960_57020-2960.png "INFINITI FX35 2005 User Guide EM-126
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
10. Remove pilot converter using the pilot bushing puller [SST] as
necessary.
11. Remove rear oil seal retainer.
Remove by inserting a scr")
EM-126
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
10. Remove pilot converter using the pilot bushing puller [SST] as
necessary.
11. Remove rear oil seal retainer.
Remove by inserting a screwdriver between main bearing cap and rear oil seal retainer.
CAUTION:
If rear oil seal retainer is removed, replace it with new one.
NOTE:
Regard both rear oil seal and retainer as an assembly.
12. Remove baffle plate from main bearing beam (2WD models).
13. Remove piston and connecting rod assembly with the following procedure:
Before removing piston and connecting rod assembly, check the connecting rod side clearance. Refer
to EM-140, "
CONNECTING ROD SIDE CLEARANCE" .
CAUTION:
Be careful not to drop connecting rod bearing, and to scratch the surface.
a. Position crankshaft pin corresponding to connecting rod to be removed onto the bottom dead center.
b. Remove connecting rod bearing cap.
c. Using a hammer handle or similar tool, push piston and connect- ing rod assembly out to the cylinder head side.
CAUTION:
Be careful not to damage the cylinder wall and crankshaft
pin, resulting from an interference of the connecting rod big
end.
14. Remove connecting rod bearings from connecting rod and connecting rod bearing cap. CAUTION:
Be careful not to drop connecting rod bearing, and to scratch the surface.
Identify installation positions, and store them without mixing them up.
15. Remove piston rings form piston.
Before removing piston rings, check the piston ring side clearance. Refer to EM-141, "PISTON RING
SIDE CLEARANCE" .
Use a piston ring expander (commercial service tool).
CAUTION:
When removing piston rings, be careful not to damage
piston.
Be careful not to damage piston rings by expanding them
excessively.
SEM005G
EMQ0191D
PBIC0087E
Page 2963 of 4731
![INFINITI FX35 2005 User Guide EM-128
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
18. Remove main bearing beam.
19. Remove main bearing caps.
CAUTION:
Be careful not to drop main bearing, and to scratch the sur-
face.](/img/42/57020/w960_57020-2962.png "INFINITI FX35 2005 User Guide EM-128
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
18. Remove main bearing beam.
19. Remove main bearing caps.
CAUTION:
Be careful not to drop main bearing, and to scratch the sur-
face.")
EM-128
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
18. Remove main bearing beam.
19. Remove main bearing caps.
CAUTION:
Be careful not to drop main bearing, and to scratch the sur-
face.
Using main bearing cap bolts, remove main bearing cap while
shaking it back-and-forth.
20. Remove crankshaft.
21. Remove main bearings and thrust bearings from cylinder block and main bearing caps. CAUTION:
Be careful not to drop main bearing, and to scratch the surface.
Identify installation positions, and store them without mixing them up.
22. Remove oil jet.
ASSEMBLY
1. Fully air-blow engine coolant and engine oil passages in cylinder block, cylinder bore and crankcase to remove any foreign material.
CAUTION:
Use a goggles to protect your eye.
2. Install each plug to cylinder block as shown in the figure.
Apply sealant to the thread of water drain plugs “A”, “B” and
“C”.
Use Genuine RTV Silicone Sealant or equivalent. Refer to
GI-48, "
RECOMMENDED CHEMICAL PRODUCTS AND
SEALANTS" .
Apply sealant to the thread of plugs “D” and “E”.
Use Genuine High Strength Thread Locking Sealant or
equivalent. Refer to GI-48, "
RECOMMENDED CHEMICAL
PRODUCTS AND SEALANTS" .
Apply sealant to the thread of plug “F”.
Use Anaerobic Liquid Gasket or equivalent. Refer to GI-
48, "RECOMMENDED CHEMICAL PRODUCTS AND SEAL-
ANTS" .
NOTE:
For Canada, “F” in the figure is not plug but block heater.
Refer to EM-122, "
Components" .
Replace washers with new one.
PBIC0881E
EMQ0195D
PBIC2610E
Page 2965 of 4731
![INFINITI FX35 2005 User Guide EM-130
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
Main bearing caps are identified by identification mark cast on
them. For installation, face front mark to front side.
NOTE:
Main bearing](/img/42/57020/w960_57020-2964.png "INFINITI FX35 2005 User Guide EM-130
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
Main bearing caps are identified by identification mark cast on
them. For installation, face front mark to front side.
NOTE:
Main bearing")
EM-130
[VQ35DE]
CYLINDER BLOCK
Revision: 2005 July 2005 FX
Main bearing caps are identified by identification mark cast on
them. For installation, face front mark to front side.
NOTE:
Main bearing cap cannot be replaced as a single part, because it
is machined together with cylinder block.
7. Install main bearing beam.
Install main bearing beam with front mark facing downward (oil pan side).
Install main bearing beam with front mark facing front of the
engine.
8. Install main bearing cap bolts in numerical order as shown in the figure as follows:
a. Inspect the outer diameter of main bearing cap bolt. Refer to EM-148, "
MAIN BEARING CAP BOLT OUTER DIAMETER" .
b. Apply new engine oil to threads and seat surfaces of main bear- ing cap bolts.
c. Tighten main bearing cap bolts in several different steps.
d. Turn all main bearing cap bolts 90 degrees clockwise (Angle tightening).
CAUTION:
Use the angle wrench [SST: KV10112100 (BT8653-A)] to
check tightening angle. Do not make judgment by visual
inspection.
After installing main bearing cap bolts, make sure that crank-
shaft can be rotated smoothly by hand.
Check the crankshaft end play. Refer to EM-140, "CRANK-
SHAFT END PLAY" .
9. Install piston to connecting rod as follows:
a. Using a snap ring pliers, install new snap ring to the groove of piston rear side.
Insert it fully into groove to install.
b. Install piston to connecting rod.
Using an industrial use drier or similar tool, heat piston until piston pin can be pushed in by hand without
excess force [approx. 60 to 70 °C (140 to 158 °F)]. From the front to the rear, insert piston pin into piston
and connecting rod.
SEM456G
PBIC0881E
: 35.3 N·m (3.6 kg-m, 26 ft-lb)
PBIC1800E
PBIC0921E
Page 2980 of 4731
![INFINITI FX35 2005 User Guide CYLINDER BLOCK EM-145
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
Revision: 2005 July 2005 FX
Piston Skirt Diameter
Measure the outer diameter of piston skirt with a micrometer.
Piston-to-Cylinde](/img/42/57020/w960_57020-2979.png "INFINITI FX35 2005 User Guide CYLINDER BLOCK EM-145
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
Revision: 2005 July 2005 FX
Piston Skirt Diameter
Measure the outer diameter of piston skirt with a micrometer.
Piston-to-Cylinde")
CYLINDER BLOCK EM-145
[VQ35DE]
C
D E
F
G H
I
J
K L
M A
EM
Revision: 2005 July 2005 FX
Piston Skirt Diameter
Measure the outer diameter of piston skirt with a micrometer.
Piston-to-Cylinder Bore Clearance
Calculate by piston skirt diameter and cylinder bore inner diameter (direction “Y”, position “B”).
(Clearance) = (Cylinder bore inner diameter) – (Piston skirt diameter).
If the calculated value exceeds the limit, replace piston and piston pin assembly. Refer to EM-135, "HOW
TO SELECT PISTON" .
Re-boring Cylinder Bore
1. Cylinder bore size is determined by adding piston to cylinder bore clearance to piston skirt diameter.
2. Install main bearing caps and main bearing beam, and tighten to the specified torque. Otherwise, cylinder bores may be distorted in final assembly.
3. Cut cylinder bores. NOTE:
When any cylinder needs boring, all other cylinders must also be bored.
Do not cut too much out of cylinder bore at a time. Cut only 0.05 mm (0.0020 in) or so in diameter at a
time.
4. Hone cylinders to obtain the specified piston to cylinder bore clearance.
5. Measure finished cylinder bore for the out-of-round and taper. NOTE:
Measurement should be done after cylinder bore cools down.
CRANKSHAFT MAIN JOURNAL DIAMETER
Measure the outer diameter of crankshaft main journals with a micrometer.
If out of the standard, measure the main bearing oil clearance. Then use undersize bearing. Refer to EM-
147, "MAIN BEARING OIL CLEARANCE" .
Measure point
: Distance from the top 41.0 mm (1.614 in)
Standard : 95.480 - 95.510 mm (3.7590 - 3.7602 in)
PBIC0125E
Standard : 0.010 - 0.030 mm (0.0004 - 0.0012 in)
Limit : 0.08 mm (0.0031 in)
Re-bored size calculation: D = A + B – C
where, D: Bored diameter
A: Piston skirt diameter as measured
B: Piston to cylinder bore clearance (standard value)
C: Honing allowance 0.02 mm (0.0008 in)
Standard : 59.951 - 59.975 mm (2.3603 - 2.3612 in) dia.
Page 3398 of 4731
IDX-5
A
C
D E
F
G H
I
J
K L
B
IDX
ALPHABETICAL INDEX
Hazard warning lamp ..........................................
LT-91
Headlamp aiming control .................................... LT-75
Headlamp leveler - See Headlamp aiming control .......
LT-75
Headlining - See Roof trim .................................. EI-41
Heated oxygen sensor 1 (bank 1) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 (bank 2) .... EC-935, EC-944,
EC-956
, EC-1174, EC-1180
Heated oxygen sensor 1 heater (bank 1) ........ EC-877
Heated oxygen sensor 1 heater (bank 2) ........ EC-877
Heated oxygen sensor 2 (bank 1) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 (bank 2) .... EC-228, EC-237,
EC-442
, EC-453, EC-966, EC-975, EC-1187, EC-1198
Heated oxygen sensor 2 heater (bank 1) ....... EC-178,
EC-885
Heated oxygen sensor 2 heater (bank 2) ....... EC-178,
EC-885
Heated seat ....................................................... SE-97
Heater and cooling unit (Heater core) ........... ATC-126
HFC134a (R134a) system precaution ............... ATC-6
HFC134a (R134a) system service procedure ATC-138
HFC134a (R134a) system service tools .......... ATC-18
HFC134a system service equipment precaution ..........
ATC-13
High and low reverse clutch solenoid valve .... AT-162,
AT-164
Hood ................................................................... BL-13
Horn ................................................................. WW-59
HORN - Wiring diagram ................................... WW-59
HSEAT - Wiring diagram ................................... SE-98
I
IATS - Wiring diagram ....................... EC-205
, EC-911
ICC - Wiring diagram ....................................... ACS-20
ICC/BS - Wiring diagram ................. EC-590, EC-1264
ICC/SW - Wiring diagram ................ EC-576, EC-1249
ICCBOF - Wiring diagram ................ EC-681, EC-1371
Idle air volume learning ....................... EC-97, EC-787
Idle mixture ratio .............................................. EC-775
Idle speed .......................................... EC-769, EC-774
Idle speed control (ISC) .... EC-393, EC-395, EC-1125,
EC-1127
Ignition coil ....................................... EC-648, EC-1339
Ignition coil(VK45DE) ...................................... EM-189
Ignition coil(VQ35DE) ........................................ EM-42
Ignition control system ..................... EC-648, EC-1339
Ignition key hole illumination ............................. LT-155
Ignition timing .................................... EC-769, EC-774
IGNSYS - Wiring diagram ................ EC-649, EC-1340
Illumination control ............................................ LT-202
In vehicle sensor ........................... ATC-107, ATC-118
INF/D - Wring diagram ....................................... AV-63
INJECT - Wiring diagram ................. EC-662, EC-1352
Injector ............................................. EC-661, EC-1351
Input clutch solenoid valve ................. AT-150, AT-152
Instrument panel .................................................. IP-10
Intake air temperature sensor ........... EC-203, EC-223,
EC-909
, EC-930
Intake door control linkage adjustment ............ ATC-78
Intake door motor ............................ ATC-76, ATC-124
Intake manifold collector(VQ35DE) .................. EM-19
Intake manifold(VK45DE) ............................... EM-178
Intake manifold(VQ35DE) ................................. EM-24
Intake sensor ................................ ATC-113, ATC-120
Intake valve timing control (Bank 1) ... EC-174, EC-865
Intake valve timing control (Bank 2) ... EC-174, EC-865
Intake valve timing control position sensor (Bank 1) ....
EC-1166
Intake valve timing control position sensor (Bank 2) ....
EC-1166
Intake valve timing control solenoid valve (Bank 1) ......
EC-417
, EC-1141
Intake valve timing control solenoid valve (Bank 2) ......
EC-417
, EC-1141
Integrated homelink transmitter ....................... BL-235
Intelligent cruise control (ICC) system .............. ACS-6
Interior ................................................................. EI-36
Interior lamp ...................................................... LT-159
IPDM (Intelligent power distribution module engine
room) ................................................................. PG-18
IVCB1 - Wiring diagram ................... EC-418, EC-1142
IVCB2 - Wiring diagram ................... EC-420, EC-1144
IVCSB1 - Wiring diagram ............................... EC-1167
IVCSB2 - Wiring diagram ............................... EC-1169
IVIS (Infiniti vehicle immobilizer system) precautions ...
GI-3
IVTB1 - Wiring diagram ................................... EC-868
IVTB2 - Wiring diagram ................................... EC-870
K
Knock sensor (KS) ........................... EC-295
, EC-1031
KS - Wiring diagram ......................... EC-296, EC-1032
L
LAN system circuit ........................................... ATC-66
Lane Departure Warning System ....................... DI-82
Laser beam aiming adjustment ....................... ACS-12
Latch (lower anchors and tether for children) system ...
SB-9
LDW .................................................................... DI-82
LDW - Wiring Diagram ........................................ DI-95
Line pressure solenoid valve ........................... AT-129
Line pressure test (A/T) ..................................... AT-54
Liquid gasket application ......................... EM-6, LU-21
Liquid gasket application(VQ35DE) ........... LU-3, CO-3
Location of electrical units ................................. PG-70
Low coast brake solenoid valve ......... AT-166, AT-168
Low tire pressure warning system ...................... WT-7
Lubricant (R134a) A/C ..................................... ATC-27
Lubrication circuit (engine)(VK45DE) ................ LU-23
Lubrication circuit (engine)(VQ35DE) .................. LU-5
Lubrication oil A/C .......................................... ATC-162
Page 3451 of 4731
![INFINITI FX35 2005 User Guide LAN-32
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Ignition switch signal T R R
P range signal T R R
Stop lamp switch signal R T
Fuel consumption monitor signal TR
RT
Turbine revolution s](/img/42/57020/w960_57020-3450.png "INFINITI FX35 2005 User Guide LAN-32
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Ignition switch signal T R R
P range signal T R R
Stop lamp switch signal R T
Fuel consumption monitor signal TR
RT
Turbine revolution s")
LAN-32
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
Ignition switch signal T R R
P range signal T R R
Stop lamp switch signal R T
Fuel consumption monitor signal TR
RT
Turbine revolution signal R T
Output shaft revolution signal R T R
A/C switch signal R T
A/C compressor request signal T R
A/C compressor feedback signal T R
Blower fan motor switch signal R T
A/C switch/indicator signal TR
RT
Cooling fan speed request signal T R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RR T
RRRR T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp signal T R
ASCD operation signal T R
ASCD OD cancel request signal T R Signals ECM TCM
Dis-
play unit BCM Steer-
ing
angle
sensor LDW
cam-
era unit Unified
meter and
A/C
amp. ABS
actua-
tor and elec-
tric unit (con-trol
unit) Driver
seat
control unit IPDM
E/R
Page 3454 of 4731
![INFINITI FX35 2005 User Guide CAN COMMUNICATION LAN-35
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Closed throttle position
signal TR R
Wide open throttle posi-
tion signal TR
Battery voltage](/img/42/57020/w960_57020-3453.png "INFINITI FX35 2005 User Guide CAN COMMUNICATION LAN-35
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Closed throttle position
signal TR R
Wide open throttle posi-
tion signal TR
Battery voltage")
CAN COMMUNICATION LAN-35
[CAN]
C
D E
F
G H
I
J
L
M A
B
LAN
Revision: 2005 July 2005 FX
Closed throttle position
signal TR R
Wide open throttle posi-
tion signal TR
Battery voltage signal T R
Key switch signal T R
Ignition switch signal T R R
P range signal T R R R
Stop lamp switch signal R T
ABS operation signal R T
TCS operation signal R T
VDC operation signal R T
Fuel consumption moni-
tor signal TR
RT
Turbine revolution signal R T R
Output shaft revolution
signal RT R R
A/C switch signal R T
A/C compressor request
signal T
R
A/C compressor feed-
back signal TR
Blower fan motor switch
signal RT
A/C switch/indicator sig-
nal TR
RT
Cooling fan speed
request signal T
R
Position light request sig-
nal TR R
Low beam request signal T R
Low beam status signal R T
High beam request sig-
nal TR R
High beam status signal R T
Front fog light request
signal TR
Day time running light
request signal TR
Turn LED burnout status
signal RT
Signals ECM TCM
Dis-
play
con-
trol
unit ICC
unit Intelli-
gent Key unit BCM Ste er-
ing
angle
sen- sor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ICC
sen-
sor ABS
actu- ator and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R
Page 3459 of 4731
![INFINITI FX35 2005 User Guide LAN-40
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
A/C switch/indicator signal TR
RT
Cooling fan speed request sig-
nal T
R
Position light request signal R T R R
Low beam request signal](/img/42/57020/w960_57020-3458.png "INFINITI FX35 2005 User Guide LAN-40
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
A/C switch/indicator signal TR
RT
Cooling fan speed request sig-
nal T
R
Position light request signal R T R R
Low beam request signal")
LAN-40
[CAN]
CAN COMMUNICATION
Revision: 2005 July 2005 FX
A/C switch/indicator signal TR
RT
Cooling fan speed request sig-
nal T
R
Position light request signal R T R R
Low beam request signal T R
Low beam status signal R T
High beam request signal T R R
High beam status signal R T
Front fog light request signal T R
Day time running light request
signal TR
Turn LED burnout status signal R T
Vehicle speed signal RRRT
RRR R T R
Sleep wake up signal T R R
Door switch signal R T R R R
Turn indicator signal T R R
Key fob ID signal T R
Key fob door unlock signal T R
Oil pressure switch signal RT
TR
Buzzer output signal T R
Fuel level sensor signal R T
Fuel level low warning signal R T
ASCD SET lamp signal T R
ASCD CRUISE lamp signal T R
Malfunction indicator lamp sig-
nal TR
Front wiper request signal T R
Front wiper stop position signal R T
Rear window defogger switch
signal TR
Rear window defogger control
signal RRR T
Hood switch signal R T
Theft warning horn request sig-
nal TR
Horn chirp signal T R
Steering angle sensor signal T R Signals ECM TCM
Dis-
play
unit AW D
con- trol
unit BCM Steer-
ing
angle
sensor LDW
cam- era
unit Uni-
fied
meter and
A/C
amp. ABS
actua- tor
and
elec- tric
unit
(con- trol
unit) Driver
seat
con-
trol
unit IPDM
E/R