Throttle INFINITI FX35 2005 Workshop Manual
[x] Cancel search | Manufacturer: INFINITI, Model Year: 2005, Model line: FX35, Model: INFINITI FX35 2005Pages: 4731, PDF Size: 60.13 MB
Page 470 of 4731
AIR CONDITIONER CONTROL ATC-33
C
D E
F
G H
I
K L
M A
B
AT C
Revision: 2005 July 2005 FX
MAGNET CLUTCH CONTROL
When A/C switch or DEF switch is pressed, unified meter and A/C amp. inputs compressor ON signal to BCM.
BCM sends compressor ON signal to ECM, via CAN communication line.
ECM judges whether compressor can be turned ON, based on each sensor status (refrigerant-pressure sen-
sor signal, throttle angle, etc.). If it judges compressor can be turned ON, it sends compressor ON signal to
IPDM E/R, via CAN communication line.
Upon receipt of compressor ON signal from ECM, IPDM E/R turns air conditioner relay ON to operate com-
pressor.
When sending compressor ON signal to IPDM E/R via CAN communication line, ECM simultaneously sends
compressor feedback signal to unified meter and A/C amp. via CAN communication line.
Unified meter and A/C amp., then, uses input compressor feedback signal to control air inlet.
SELF-DIAGNOSIS SYSTEM
The self-diagnosis system is built into the unified meter and A/C amp. to quickly locate the cause of symp-
toms.
RJIA1957E
Page 563 of 4731
ATC-126
HEATER & COOLING UNIT ASSEMBLY
Revision: 2005 July 2005 FX
HEATER & COOLING UNIT ASSEMBLYPFP:27110
Removal and InstallationAJS0015J
REMOVAL
1. Use a refrigerant collecting equipment (for HFC-134a) to discharge refrigerant.
2. Drain coolant from cooling system. Refer to CO-11, "
Changing Engine Coolant" (VQ35DE) or CO-37,
"Changing Engine Coolant" (VK45DE).
3. Remove cowl top cover. Refer to EI-23, "
COWL TOP" .
4. Remove high-pressure pipe 2 mounting clip.
5. Remove low-pressure flexible hose bracket mounting bolt.
6. Disconnect low-pressure pipe 1 and high-pressure pipe 2 from evaporator.
a. Set a disconnector [High-pressure side (SST: 9253089908), Low-pressure side (SST: 9253089916)] on A/C piping.
b. Slide a disconnector toward vehicle front until it clicks.
c. Slide A/C piping toward vehicle front and disconnect it. CAUTION:
Cap or wrap the joint of the pipe with suitable material such
as vinyl tape to avoid the entry of air.
7. Remove electric throttle control actuator (VQ35DE). Refer to EM-19, "
INTAKE MANIFOLD COLLECTOR" .
8. Disconnect two heater hoses from heater core.
9. Remove instrument panel assembly. Refer to IP-11, "
Removal
and Installation" .
10. Remove blower unit. Refer to ATC-121, "
BLOWER UNIT" .
RJIA2037E
RJIA2041E
RJIA2077E
Page 1149 of 4731
![INFINITI FX35 2005 Workshop Manual BRC-8
[VDC/TCS/ABS]
SYSTEM DESCRIPTION
Revision: 2005 July 2005 FX
SYSTEM DESCRIPTIONPFP:00000
System DiagramAFS001SB
VDC FunctionAFS001SC
In addition to the TCS/ABS function, the driver steering amo](/img/42/57020/w960_57020-1148.png "INFINITI FX35 2005 Workshop Manual BRC-8
[VDC/TCS/ABS]
SYSTEM DESCRIPTION
Revision: 2005 July 2005 FX
SYSTEM DESCRIPTIONPFP:00000
System DiagramAFS001SB
VDC FunctionAFS001SC
In addition to the TCS/ABS function, the driver steering amo")
BRC-8
[VDC/TCS/ABS]
SYSTEM DESCRIPTION
Revision: 2005 July 2005 FX
SYSTEM DESCRIPTIONPFP:00000
System DiagramAFS001SB
VDC FunctionAFS001SC
In addition to the TCS/ABS function, the driver steering amount and brake operation amount are detected
from steering angle sensor and pressure sensor, and the vehicle's driving status (amount of under steer-
ing / over steering) is determined from information from G sensor, wheel sensor, etc., and this information
is used to improve vehicle stability by controlling the braking and engine power to all four wheels.
SLIP indicator lamp flashes to inform the driver of VDC operation.
During VDC operation, body and brake pedal lightly vibrate and mechanical noises may be heard. This is
normal.
ABS warning lamp, VDC OFF indicator lamp, and SLIP indicator lamp might turn on when vehicle is sub-
ject to strong shaking or large vibration, such as when vehicle is on a turn table, a ship or a steep slope
such as bank while engine is running. In this case, restart engine on a normal road, and if ABS warning
lamp, VDC OFF indicator lamp, and SLIP indicator lamp turn off, there is no malfunction.
TCS FunctionAFS001SD
The wheel spin of the drive wheels is detected by ABS actuator and electric unit (control unit) from the
wheel speed signals from four wheels, so if wheel spin occurs, drive wheel right and left brake fluid pres-
sure control and engine fuel cut are performed while throttle value is restricted to reduce the engine
torque and decrease the amount of wheel spin. In addition, the degree throttle is opened is controlled to
achieve the optimum engine torque.
Depending on road circumstances, the driver may have a sluggish feel. This is normal, because the opti-
mum traction has the highest priority under TCS operation.
TCS may be activated any time vehicle suddenly accelerates, suddenly down/upshifts, or is driven on a
road with a varying surface friction coefficient.
During TCS operation, it informs a driver of system operation by flashing SLIP indicator lamp.
ABS FunctionAFS001SE
The anti-lock brake system is a function that detects wheel revolution while braking, and it improves han-
dling stability during sudden braking by electrically preventing 4 wheel lock. Maneuverability is also
improved for avoiding obstacles.
If the electrical system malfunctions, then the fail-safe function starts, the ABS becomes inoperative, and
ABS warning lamp turns on.
Electrical system diagnosis by CONSULT-II is available.
During ABS operation, brake pedal lightly vibrates and a mechanical noise may be heard. This is normal.
SFIA1160E
Page 1164 of 4731
![INFINITI FX35 2005 Workshop Manual TROUBLE DIAGNOSIS BRC-23
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
Control Unit Input/Output Signal StandardAFS001SP
REFERENCE VALUE FROM CONSULT-II
CAUTION:](/img/42/57020/w960_57020-1163.png "INFINITI FX35 2005 Workshop Manual TROUBLE DIAGNOSIS BRC-23
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
Control Unit Input/Output Signal StandardAFS001SP
REFERENCE VALUE FROM CONSULT-II
CAUTION:")
TROUBLE DIAGNOSIS BRC-23
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
Control Unit Input/Output Signal StandardAFS001SP
REFERENCE VALUE FROM CONSULT-II
CAUTION:
The display shows ABS actuator and electric unit (control unit) calculation data, so a normal value
might be displayed even in the event the output circuit (harness) is open or short-circuited.
Monitor item Display content Data monitor
Check item
Condition Reference value in
normal operation
SLCT LVR POSI A/T shift position P: P position
R: R position
N: N position
D: D position
—
GEAR A/T gear position 1: 1st gear
2: 2nd gear
3: 3rd gear
4: 4th gear
5: 5th gear
FR RH SENSOR
FR LH SENSOR
RR RH SENSOR
RR LH SENSOR Wheel speed Vehicle stopped 0 [km/h (MPH)]
BRC-37, "
Inspection 1:
Wheel Sensor Circuit"Vehicle running (Note 1) Almost in accor-
dance with speed-
ometer display
(within ±10 %)
ACCEL POS SIG Open/close condition
of throttle valve (linked
with accelerator pedal). Accelerator pedal not
depressed (ignition switch is
ON) 0 %
Communication circuit
between VDC/TCS/ABS
control unit and ECM
Depress accelerator pedal
(ignition switch is ON) 0 to 100 %
ENGINE SPEED With engine running With engine stopped 0 rpm
EC section
Engine running Almost in accor-
dance with
tachometer display
STR ANGLE SIG Steering angle
detected by steering
angle sensor Straight-ahead Approx. 0 deg
BRC-42, "
Inspection 5:
Steering Angle Sensor
Circuit"Steering wheel turned –756 to 756 deg
YAW RATE SEN Yaw rate detected by
yaw rate sensor Vehicle stopped Approx. 0 d/s
BRC-44, "
Inspection 6:
Yaw Rate/Side G Sensor
(2WD Model), Yaw Rate/
Side/Decel G sensor
(AWD Models) Circuit"
Vehicle running –100 to 100 d/s
SIDE G-SENSOR Transverse G detected
by side G sensor Vehicle stopped
Approx. 0 m/s
2BRC-44, "Inspection 6:
Yaw Rate/Side G Sensor
(2WD Model), Yaw Rate/
Side/Decel G sensor
(AWD Models) Circuit"
Vehicle running–16.7 to 16.7 m/s2
PRESS SENSOR Brake fluid pressure
detected by pressure
sensor With ignition switch turned ON
and brake pedal released Approx. 0 bar
BRC-40, "Inspection 4:
Pressure Sensor Circuit"With ignition switch turned ON
and brake pedal depressed 0 to 170 bar
BATTERY VOLT Battery voltage sup-
plied to ABS actuator
and electric unit (con-
trol unit) Ignition switch ON 10 to 16 V BRC-48, "
Inspection 9:
ABS Actuator and Elec-
tric Unit (Control Unit)
Power Supply and
Ground Circuit"
STOP LAMP SW Brake pedal operation
Brake pedal depressed ON
BRC-50, "
Inspection 10:
Stop Lamp Switch Cir-
cuit"Brake pedal not depressed OFF
Page 1172 of 4731
![INFINITI FX35 2005 Workshop Manual TROUBLE DIAGNOSIS BRC-31
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
CAUTION:
When “START (NISSAN BASED VHCL)” is touched immediately after starting engine](/img/42/57020/w960_57020-1171.png "INFINITI FX35 2005 Workshop Manual TROUBLE DIAGNOSIS BRC-31
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
CAUTION:
When “START (NISSAN BASED VHCL)” is touched immediately after starting engine")
TROUBLE DIAGNOSIS BRC-31
[VDC/TCS/ABS]
C
D E
G H
I
J
K L
M A
B
BRC
Revision: 2005 July 2005 FX
CAUTION:
When “START (NISSAN BASED VHCL)” is touched immediately after starting engine or turning on
ignition switch, “ABS” might not be displayed in the system selection screen. In this case, repeat
the operation from step 1.
4. Return to the Monitor Item Selection screen, and touch “ECU INPUT SIGNALS”, “MAIN SIGNALS” or “SELECTION FROM MENU”. Refer to the following information.
5. When “START” is touched, the data monitor screen is displayed.
Display Item List
Item
(Unit) Data monitor item selection
Remarks
ECU INPUT
SIGNALS MAIN
SIGNALS SELECTION
FROM MENU
GEAR ××× Gear position judged by PNP
switch signal is displayed.
FR RH SENSOR
(km/h, MPH) ××× Wheel speed calculated by front
RH wheel sensor signal is dis-
played.
FR LH SENSOR
(km/h, MPH) ××× Wheel speed calculated by front
LH wheel sensor signal is dis-
played.
RR RH SENSOR
(km/h, MPH) ××× Wheel speed calculated by rear
RH wheel sensor signal is dis-
played.
RR LH SENSOR
(km/h, MPH) ××× Wheel speed calculated by rear
LH wheel sensor signal is dis-
played.
BATTERY VOLT
(V) ××× Voltage supplied to ABS actuator
and electric unit (control unit) is
displayed.
SLCT LVR POSI ××× Shift position judged by PNP
switch signal.
ACCEL POS SIG
(%) ×
–– Throttle valve open/close status
judged by CAN communication
signal is displayed.
ENGINE SPEED
(rpm) ××× Engine speed judged by CAN
communication signal is displayed.
STR ANGLE SIG
(deg) ×
–– Steering angle detected by steer-
ing angle sensor is displayed.
YAW RATE SEN
(d/s) ××
– Yaw rate detected by yaw rate
sensor is displayed.
DECEL G-SEN (AWD model)
(G) ××× Longitudinal acceleration detected
by decel G-sensor is displayed.
SIDE G-SENSOR
(m/s
2 ) ×
–– Lateral acceleration detected by
side G-sensor is displayed.
PRESS SENSOR
(bar) ×
–– Brake fluid pressure detected by
pressure sensor is displayed.
STOP LAMP SW
(ON/OFF) ××× Stop lamp switch (ON/OFF) status
is displayed.
OFF SW
(ON/OFF)
×× × VDC OFF switch (ON/OFF) sta-
tus is displayed.
ABS WARN LAMP
(ON/OFF) –
×× ABS warning lamp (ON/OFF) sta-
tus is displayed.
SLIP LAMP
(ON/OFF) –
×× SLIP indicator lamp (ON/OFF) sta-
tus is displayed.
FR LH IN SOL
(ON/OFF) –
×× Front LH IN ABS solenoid (ON/
OFF) status is displayed.
Page 1394 of 4731
EC-1
ENGINE CONTROL SYSTEM
B ENGINE
CONTENTS
C
D E
F
G H
I
J
K L
M
SECTION EC
A
EC
Revision: 2005 July 2005 FX
ENGINE CONTROL SYSTEM
VQ35DE
INDEX FOR DTC ...................................................... 15
DTC No. Index .................................................... ... 15
Alphabetical Index ............................................... ... 19
PRECAUTIONS ..................................................... ... 23
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ... 23
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... ... 23
Precaution ........................................................... ... 23
PREPARATION ...................................................... ... 27
Special Service Tools .......................................... ... 27
Commercial Service Tools ................................... ... 29
ENGINE CONTROL SYSTEM ............................... ... 30
System Diagram .................................................. ... 30
Multiport Fuel Injection (MFI) System ................. ... 31
Electronic Ignition (EI) System ............................ ... 33
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. ... 34
AIR CONDITIONING CUT CONTROL .................. ... 35
Input/Output Signal Chart .................................... ... 35
System Description ............................................. ... 35
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ... 36
System Description ............................................. ... 36
Component Description ....................................... ... 37
CAN COMMUNICATION ....................................... ... 38
System Description ............................................. ... 38
EVAPORATIVE EMISSION SYSTEM .................... ... 39
Description .......................................................... ... 39
Component Inspection ........................................ ... 42
Removal and Installation ..................................... ... 43
How to Detect Fuel Vapor Leakage .................... ... 43
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... ... 46
System Description ............................................. ... 46
Diagnostic Procedure .......................................... ... 47
Component Inspection ........................................ ... 49 POSITIVE CRANKCASE VENTILATION ..............
... 51
Description ........................................................... ... 51
Component Inspection ......................................... ... 51
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... ... 53
Description ........................................................... ... 53
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 54
Introduction .......................................................... ... 54
Two Trip Detection Logic ..................................... ... 54
Emission-Related Diagnostic Information ............ ... 55
Malfunction Indicator Lamp (MIL) ........................ ... 69
OBD System Operation Chart ............................. ... 72
BASIC SERVICE PROCEDURE ............................ ... 78
Basic Inspection .................................................. ... 78
Idle Speed and Ignition Timing Check ................. ... 83
Idle Mixture Ratio Adjustment .............................. ... 85
VIN Registration .................................................. ... 96
Accelerator Pedal Released Position Learning ... ... 96
Throttle Valve Closed Position Learning .............. ... 96
Idle Air Volume Learning ..................................... ... 97
Fuel Pressure Check ........................................... ... 99
TROUBLE DIAGNOSIS ......................................... .101
Trouble Diagnosis Introduction ............................ .101
DTC Inspection Priority Chart .............................. .107
Fail-Safe Chart .................................................... .109
Symptom Matrix Chart ......................................... .110
Engine Control Component Parts Location ......... .114
Vacuum Hose Drawing ........................................ .120
Circuit Diagram .................................................... .121
ECM Harness Connector Terminal Layout .......... .123
ECM Terminals and Reference Value .................. .123
CONSULT-II Function (ENGINE) ......................... .132
Generic Scan Tool (GST) Function ...................... .144
CONSULT-II Reference Value in Data Monitor .... .147
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .151
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .153
Description ........................................................... .153
Testing Condition ................................................. .153
Page 1397 of 4731
EC-4Revision: 2005 July 2005 FX
On Board Diagnosis Logic ...................................
.350
DTC Confirmation Procedure .............................. .351
Diagnostic Procedure .......................................... .351
Component Inspection ......................................... .352
DTC P0452 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .353
Component Description ....................................... .353
CONSULT-II Reference Value in Data Monitor Mode .353
On Board Diagnosis Logic ................................... .353
DTC Confirmation Procedure .............................. .354
Wiring Diagram .................................................... .355
Diagnostic Procedure .......................................... .356
Component Inspection ......................................... .358
DTC P0453 EVAP CONTROL SYSTEM PRESSURE
SENSOR ................................................................. .359
Component Description ....................................... .359
CONSULT-II Reference Value in Data Monitor Mode .359
On Board Diagnosis Logic ................................... .359
DTC Confirmation Procedure .............................. .360
Wiring Diagram .................................................... .361
Diagnostic Procedure .......................................... .362
Component Inspection ......................................... .366
DTC P0455 EVAP CONTROL SYSTEM ................ .367
On Board Diagnosis Logic ................................... .367
DTC Confirmation Procedure .............................. .368
Diagnostic Procedure .......................................... .369
DTC P0456 EVAP CONTROL SYSTEM ................ .375
On Board Diagnosis Logic ................................... .375
DTC Confirmation Procedure .............................. .376
Overall Function Check ....................................... .377
Diagnostic Procedure .......................................... .378
DTC P0460 FUEL LEVEL SENSOR ...................... .385
Component Description ....................................... .385
On Board Diagnosis Logic ................................... .385
DTC Confirmation Procedure .............................. .385
Diagnostic Procedure .......................................... .386
Removal and Installation ..................................... .386
DTC P0461 FUEL LEVEL SENSOR ...................... .387
Component Description ....................................... .387
On Board Diagnosis Logic ................................... .387
Overall Function Check ....................................... .387
Diagnostic Procedure .......................................... .388
Removal and Installation ..................................... .388
DTC P0462, P0463 FUEL LEVEL SENSOR ......... .389
Component Description ....................................... .389
On Board Diagnosis Logic ................................... .389
DTC Confirmation Procedure .............................. .389
Diagnostic Procedure .......................................... .390
Removal and Installation ..................................... .390
DTC P0500 VSS ..................................................... .391
Description ........................................................... .391
On Board Diagnosis Logic ................................... .391
DTC Confirmation Procedure .............................. .391
Overall Function Check ....................................... .391
Diagnostic Procedure .......................................... .392
DTC P0506 ISC SYSTEM ...................................... .393
Description ........................................................... .393 On Board Diagnosis Logic ...................................
.393
DTC Confirmation Procedure ............................... .393
Diagnostic Procedure ........................................... .394
DTC P0507 ISC SYSTEM ...................................... .395
Description ........................................................... .395
On Board Diagnosis Logic ................................... .395
DTC Confirmation Procedure ............................... .395
Diagnostic Procedure ........................................... .396
DTC P0550 PSP SENSOR ..................................... .397
Component Description ....................................... .397
CONSULT-II Reference Value in Data Monitor Mode .397
On Board Diagnosis Logic ................................... .397
DTC Confirmation Procedure ............................... .397
Wiring Diagram .................................................... .398
Diagnostic Procedure ........................................... .399
Component Inspection ......................................... .401
Removal and Installation ...................................... .401
DTC P0605 ECM .................................................... .402
Component Description ....................................... .402
On Board Diagnosis Logic ................................... .402
DTC Confirmation Procedure ............................... .402
Diagnostic Procedure ........................................... .403
DTC P1031, P1032, P1051, P1052 A/F SENSOR 1
HEATER .................................................................. .405
Description ........................................................... .405
CONSULT-II Reference Value in Data Monitor Mode .405
On Board Diagnosis Logic ................................... .405
DTC Confirmation Procedure ............................... .405
Wiring Diagram .................................................... .407
Diagnostic Procedure ........................................... .410
Component Inspection ......................................... .412
Removal and Installation ...................................... .412
DTC P1065 ECM POWER SUPPLY ....................... .413
Component Description ....................................... .413
On Board Diagnosis Logic ................................... .413
DTC Confirmation Procedure ............................... .413
Wiring Diagram .................................................... .414
Diagnostic Procedure ........................................... .415
D T C P1111, P 1 136 IVT CONTROL SOLENOID
VALVE ..................................................................... .417
Component Description ....................................... .417
CONSULT-II Reference Value in Data Monitor Mode .417
On Board Diagnosis Logic ................................... .417
DTC Confirmation Procedure ............................... .417
Wiring Diagram .................................................... .418
Diagnostic Procedure ........................................... .421
Component Inspection ......................................... .422
Removal and Installation ...................................... .423
DTC P1121 ELECTRIC THROTTLE CONTROL
ACTUATOR ............................................................ .424
Component Description ....................................... .424
On Board Diagnosis Logic ................................... .424
DTC Confirmation Procedure ............................... .424
Diagnostic Procedure ........................................... .425
DTC P1122 ELECTRIC THROTTLE CONTROL
Page 1398 of 4731
EC-5
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2005 July 2005 FX
FUNCTION .............................................................
. 426
Description .......................................................... . 426
On Board Diagnosis Logic .................................. . 426
DTC Confirmation Procedure .............................. . 426
Wiring Diagram ................................................... . 427
Diagnostic Procedure .......................................... . 428
Component Inspection ........................................ . 431
Remove and Installation ...................................... . 431
DTC P1124, P1126 THROTTLE CONTROL MOTOR
RELAY ................................................................... . 432
Component Description ....................................... . 432
CONSULT-II Reference Value in Data Monitor Mode . 432
On Board Diagnosis Logic .................................. . 432
DTC Confirmation Procedure .............................. . 432
Wiring Diagram ................................................... . 434
Diagnostic Procedure .......................................... . 435
DTC P1128 THROTTLE CONTROL MOTOR ....... . 437
Component Description ....................................... . 437
On Board Diagnosis Logic .................................. . 437
DTC Confirmation Procedure .............................. . 437
Wiring Diagram ................................................... . 438
Diagnostic Procedure .......................................... . 439
Component Inspection ........................................ . 440
Removal and Installation ..................................... . 441
DTC P1146, P1166 HO2S2 .................................... . 442
Component Description ....................................... . 442
CONSULT-II Reference Value in Data Monitor Mode . 442
On Board Diagnosis Logic .................................. . 442
DTC Confirmation Procedure .............................. . 443
Overall Function Check ....................................... . 443
Wiring Diagram ................................................... . 445
Diagnostic Procedure .......................................... . 448
Component Inspection ........................................ . 450
Removal and Installation ..................................... . 452
DTC P1147, P1167 HO2S2 .................................... . 453
Component Description ....................................... . 453
CONSULT-II Reference Value in Data Monitor Mode . 453
On Board Diagnosis Logic .................................. . 453
DTC Confirmation Procedure .............................. . 454
Overall Function Check ....................................... . 454
Wiring Diagram ................................................... . 456
Diagnostic Procedure .......................................... . 459
Component Inspection ........................................ . 461
Removal and Installation ..................................... . 463
DTC P1148, P1168 CLOSED LOOP CONTROL ... . 464
On Board Diagnosis Logic .................................. . 464
DTC P1211 TCS CONTROL UNIT ........................ . 465
Description .......................................................... . 465
On Board Diagnosis Logic .................................. . 465
DTC Confirmation Procedure .............................. . 465
Diagnostic Procedure .......................................... . 465
DTC P1212 TCS COMMUNICATION LINE ........... . 466
Description .......................................................... . 466
On Board Diagnosis Logic .................................. . 466
DTC Confirmation Procedure .............................. . 466
Diagnostic Procedure .......................................... . 466 DTC P1217 ENGINE OVER TEMPERATURE .......
.467
Description ........................................................... .467
CONSULT-II Reference Value in Data Monitor Mode .469
On Board Diagnosis Logic ................................... .469
Overall Function Check ....................................... .469
Wiring Diagram .................................................... .471
Diagnostic Procedure .......................................... .473
Main 12 Causes of Overheating .......................... .478
Component Inspection ......................................... .478
DTC P1225 TP SENSOR ....................................... .479
Component Description ....................................... .479
On Board Diagnosis Logic ................................... .479
DTC Confirmation Procedure .............................. .479
Diagnostic Procedure .......................................... .480
Removal and Installation ..................................... .480
DTC P1226 TP SENSOR ....................................... .481
Component Description ....................................... .481
On Board Diagnosis Logic ................................... .481
DTC Confirmation Procedure .............................. .481
Diagnostic Procedure .......................................... .482
Removal and Installation ..................................... .482
DTC P1229 SENSOR POWER SUPPLY ............... .483
On Board Diagnosis Logic ................................... .483
DTC Confirmation Procedure .............................. .483
Wiring Diagram .................................................... .484
Diagnostic Procedure .......................................... .485
DTC P1271, P1281 A/F SENSOR 1 ...................... .488
Component Description ....................................... .488
CONSULT-II Reference Value in Data Monitor Mode .488
On Board Diagnosis Logic ................................... .488
DTC Confirmation Procedure .............................. .488
Wiring Diagram .................................................... .490
Diagnostic Procedure .......................................... .493
Removal and Installation ..................................... .496
DTC P1272, P1282 A/F SENSOR 1 ...................... .497
Component Description ....................................... .497
CONSULT-II Reference Value in Data Monitor Mode .497
On Board Diagnosis Logic ................................... .497
DTC Confirmation Procedure .............................. .497
Wiring Diagram .................................................... .499
Diagnostic Procedure .......................................... .502
Removal and Installation ..................................... .505
DTC P1273, P1283 A/F SENSOR 1 ...................... .506
Component Description ....................................... .506
CONSULT-II Reference Value in Data Monitor Mode .506
On Board Diagnosis Logic ................................... .506
DTC Confirmation Procedure .............................. .506
Wiring Diagram .................................................... .508
Diagnostic Procedure .......................................... .511
Removal and Installation ..................................... .515
DTC P1274, P1284 A/F SENSOR 1 ...................... .516
Component Description ....................................... .516
CONSULT-II Reference Value in Data Monitor Mode .516
On Board Diagnosis Logic ................................... .516
Page 1400 of 4731
EC-7
C
D E
F
G H
I
J
K L
M
EC A
Revision: 2005 July 2005 FX
Wiring Diagram ...................................................
. 615
Diagnostic Procedure .......................................... . 616
Component Inspection ........................................ . 618
DTC P2122, P2123 APP SENSOR ....................... . 619
Component Description ....................................... . 619
CONSULT-II Reference Value in Data Monitor Mode . 619
On Board Diagnosis Logic .................................. . 619
DTC Confirmation Procedure .............................. . 620
Wiring Diagram ................................................... . 621
Diagnostic Procedure .......................................... . 622
Component Inspection ........................................ . 624
Removal and Installation ..................................... . 625
DTC P2127, P2128 APP SENSOR ....................... . 626
Component Description ....................................... . 626
CONSULT-II Reference Value in Data Monitor Mode . 626
On Board Diagnosis Logic .................................. . 626
DTC Confirmation Procedure .............................. . 627
Wiring Diagram ................................................... . 628
Diagnostic Procedure .......................................... . 629
Component Inspection ........................................ . 632
Removal and Installation ..................................... . 632
DTC P2135 TP SENSOR ....................................... . 633
Component Description ....................................... . 633
CONSULT-II Reference Value in Data Monitor Mode . 633
On Board Diagnosis Logic .................................. . 633
DTC Confirmation Procedure .............................. . 634
Wiring Diagram ................................................... . 635
Diagnostic Procedure .......................................... . 636
Component Inspection ........................................ . 639
Removal and Installation ..................................... . 639
DTC P2138 APP SENSOR .................................... . 640
Component Description ....................................... . 640
CONSULT-II Reference Value in Data Monitor Mode . 640
On Board Diagnosis Logic .................................. . 640
DTC Confirmation Procedure .............................. . 641
Wiring Diagram ................................................... . 642
Diagnostic Procedure .......................................... . 643
Component Inspection ........................................ . 647
Removal and Installation ..................................... . 647
IGNITION SIGNAL ................................................. . 648
Component Description ....................................... . 648
Wiring Diagram ................................................... . 649
Diagnostic Procedure .......................................... . 654
Component Inspection ........................................ . 659
Removal and Installation ..................................... . 660
INJECTOR CIRCUIT .............................................. . 661
Component Description ....................................... . 661
CONSULT-II Reference Value in Data Monitor Mode . 661
Wiring Diagram ................................................... . 662
Diagnostic Procedure .......................................... . 663
Component Inspection ........................................ . 667
Removal and Installation ..................................... . 667
FUEL PUMP CIRCUIT ........................................... . 668
Description .......................................................... . 668 CONSULT-II Reference Value in Data Monitor Mode
.668
Wiring Diagram .................................................... .669
Diagnostic Procedure .......................................... .670
Component Inspection ......................................... .672
Removal and Installation ..................................... .673
REFRIGERANT PRESSURE SENSOR ................. .674
Component Description ....................................... .674
Wiring Diagram .................................................... .675
Diagnostic Procedure .......................................... .676
Removal and Installation ..................................... .678
ELECTRICAL LOAD SIGNAL ............................... .679
Description ........................................................... .679
CONSULT-II Reference Value in Data Monitor Mode .679
Diagnostic Procedure .......................................... .679
ICC BRAKE SWITCH ............................................ .680
Component Description ....................................... .680
CONSULT-II Reference Value in Data Monitor Mode .680
Wiring Diagram .................................................... .681
Diagnostic Procedure .......................................... .682
Component Inspection ......................................... .687
ASCD BRAKE SWITCH ........................................ .688
Component Description ....................................... .688
CONSULT-II Reference Value in Data Monitor Mode .688
Wiring Diagram .................................................... .689
Diagnostic Procedure .......................................... .690
Component Inspection ......................................... .694
ASCD INDICATOR ................................................. .695
Component Description ....................................... .695
CONSULT-II Reference Value in Data Monitor Mode .695
Wiring Diagram .................................................... .696
Diagnostic Procedure .......................................... .697
SNOW MODE SWITCH ......................................... .698
Description ........................................................... .698
CONSULT-II Reference Value in the Data Monitor
Mode .................................................................... .698
Wiring Diagram .................................................... .699
Diagnostic Procedure .......................................... .700
Component Inspection ......................................... .702
MIL AND DATA LINK CONNECTOR ..................... .703
Wiring Diagram .................................................... .703
SERVICE DATA AND SPECIFICATIONS (SDS) ... .705
Fuel Pressure ...................................................... .705
Idle Speed and Ignition Timing ............................ .705
Calculated Load Value ......................................... .705
Mass Air Flow Sensor .......................................... .705
Intake Air Temperature Sensor ............................ .705
Engine Coolant Temperature Sensor .................. .705
Air Fuel Ratio (A/F) Sensor 1 Heater ................... .705
Heated Oxygen sensor 2 Heater ......................... .705
Crankshaft Position Sensor (POS) ...................... .705
Camshaft Position Sensor (PHASE) ................... .705
Throttle Control Motor .......................................... .705
Injector ................................................................. .706
Fuel Pump ........................................................... .706
Page 1401 of 4731
EC-8Revision: 2005 July 2005 FX
VK45DE
INDEX FOR DTC .....................................................707
DTC No. Index ..................................................... .707
Alphabetical Index ............................................... .711
PRECAUTIONS ...................................................... .715
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” .............................................................. .715
On Board Diagnostic (OBD) System of Engine and
A/T ....................................................................... .715
Precaution ........................................................... .715
PREPARATION ...................................................... .719
Special Service Tools .......................................... .719
Commercial Service Tools ................................... .720
ENGINE CONTROL SYSTEM ............................... .721
System Diagram .................................................. .721
Multiport Fuel Injection (MFI) System .................. .722
Electronic Ignition (EI) System ............................ .724
Fuel Cut Control (at No Load and High Engine
Speed) ................................................................. .725
AIR CONDITIONING CUT CONTROL ................... .726
Input/Output Signal Chart .................................... .726
System Description .............................................. .726
AUTOMATIC SPEED CONTROL DEVICE (ASCD) .727
System Description .............................................. .727
Component Description ....................................... .728
CAN COMMUNICATION ........................................ .729
System Description .............................................. .729
EVAPORATIVE EMISSION SYSTEM .................... .730
Description ........................................................... .730
Component Inspection ......................................... .733
Removal and Installation ..................................... .734
How to Detect Fuel Vapor Leakage ..................... .734
ON BOARD REFUELING VAPOR RECOVERY
(ORVR) ................................................................... .737
System Description .............................................. .737
Diagnostic Procedure .......................................... .738
Component Inspection ......................................... .740
POSITIVE CRANKCASE VENTILATION .............. .742
Description ........................................................... .742
Component Inspection ......................................... .742
IVIS (INFINITI VEHICLE IMMOBILIZER SYSTEM-
NATS) ..................................................................... .744
Description ........................................................... .744
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... .745
Introduction .......................................................... .745
Two Trip Detection Logic ..................................... .745
Emission-Related Diagnostic Information ............ .746
Malfunction Indicator Lamp (MIL) ........................ .760
OBD System Operation Chart ............................. .764
BASIC SERVICE PROCEDURE ............................ .769
Basic Inspection .................................................. .769
Idle Speed and Ignition Timing Check ................. .774
Idle Mixture Ratio Adjustment .............................. .775
VIN Registration .................................................. .786
Accelerator Pedal Released Position Learning ... .786
Throttle Valve Closed Position Learning .............. .786 Idle Air Volume Learning ......................................
.787
Fuel Pressure Check ........................................... .789
TROUBLE DIAGNOSIS ......................................... .791
Trouble Diagnosis Introduction ............................ .791
DTC Inspection Priority Chart .............................. .797
Fail-Safe Chart ..................................................... .799
Symptom Matrix Chart ......................................... .800
Engine Control Component Parts Location .......... .804
Vacuum Hose Drawing ........................................ .810
Circuit Diagram .................................................... .811
ECM Harness Connector Terminal Layout ........... .813
ECM Terminals and Reference Value .................. .813
CONSULT-II Function (ENGINE) ......................... .822
Generic Scan Tool (GST) Function ...................... .835
CONSULT-II Reference Value in Data Monitor .... .838
Major Sensor Reference Graph in Data Monitor
Mode .................................................................... .842
TROUBLE DIAGNOSIS - SPECIFICATION VALUE .844
Description ........................................................... .844
Testing Condition ................................................. .844
Inspection Procedure ........................................... .844
Diagnostic Procedure ........................................... .845
TROUBLE DIAGNOSIS FOR INTERMITTENT INCI-
DENT ...................................................................... .854
Description ........................................................... .854
Diagnostic Procedure ........................................... .854
POWER SUPPLY AND GROUND CIRCUIT .......... .855
Wiring Diagram .................................................... .855
Diagnostic Procedure ........................................... .856
Ground Inspection ................................................ .861
DTC U1000, U1001 CAN COMMUNICATION LINE .862
Description ........................................................... .862
On Board Diagnosis Logic ................................... .862
DTC Confirmation Procedure ............................... .862
Wiring Diagram .................................................... .863
Diagnostic Procedure ........................................... .864
DTC P0011, P0021 IVT CONTROL ........................ .865
Description ........................................................... .865
CONSULT-II Reference Value in Data Monitor Mode .866
On Board Diagnosis Logic ................................... .866
DTC Confirmation Procedure ............................... .867
Wiring Diagram .................................................... .868
Diagnostic Procedure ........................................... .871
Component Inspection ......................................... .875
Removal and Installation ...................................... .876
DTC P0031, P0032, P0051, P0052 HO2S1 HEATER .877
Description ........................................................... .877
CONSULT-II Reference Value in Data Monitor Mode .877
On Board Diagnosis Logic ................................... .877
DTC Confirmation Procedure ............................... .878
Wiring Diagram .................................................... .879
Diagnostic Procedure ........................................... .882
Component Inspection ......................................... .884
Removal and Installation ...................................... .884
DTC P0037, P0038, P0057, P0058 HO2S2 HEATER .885
Description ........................................................... .885
CONSULT-II Reference Value in Data Monitor Mode