service INFINITI FX35 2005 Service Manual

ACC-2
PRECAUTIONS
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ABS00A37
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.

ACS-1
AUTO CRUISE CONTROL SYSTEM
K ELECTRICAL
CONTENTS
C
D E
F
G H
I
J
L
M
SECTION ACS
A
B
ACS
Revision: 2005 July 2005 FX
AUTO CRUISE CONTROL SYSTEM
ASCD
AUTOMATIC SPEED CONTROL DEVICE (ASCD) ..... 3
Description .......................................................... ..... 3
ICC
PRECAUTIONS ..................................................... ..... 4
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 4
Precautions for ICC System Service ................... ..... 4
PREPARATION ...................................................... ..... 5
Special Service Tools .......................................... ..... 5
DESCRIPTION ....................................................... ..... 6
Outline ................................................................. ..... 6
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE .............................................................. ..... 6
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................ ..... 6
BRAKE ASSIST (WITH PREVIEW FUNCTION) ..... 6
System Diagram .................................................. ..... 6
Components Description ..................................... ..... 7
CAN Communication ........................................... ..... 7
CAN COMMUNICATION UNIT ........................ ..... 7
Switch Operation ................................................. ..... 8
ICC System Display ............................................ ..... 8
ACTION TEST ....................................................... ..... 9
ICC System Running Test ................................... ..... 9
VEHICLE-TO-VEHICLE DISTANCE CONTROL
MODE .............................................................. ..... 9
CONVENTIONAL (FIXED SPEED) CRUISE
CONTROL MODE ............................................ ... 10
LASER BEAM AIMING ADJUSTMENT ................ ... 12
Outline ................................................................. ... 12
Preparation .......................................................... ... 12
Outline of Adjustment Procedure ........................ ... 12
Setting the ICC Target Board .............................. ... 12
ADJUSTING HEIGHT OF THE TARGET ......... ... 12
ADJUSTING THE RIGHT-LEFT POSITION OF
THE TARGET ................................................... ... 13 SETTING THE TARGET ..................................
... 13
Aiming Adjustment ............................................... ... 14
CHECK AFTER THE ADJUSTMENT ............... ... 17
ELECTRICAL UNITS LOCATION ......................... ... 18
Component Parts and Harness Connector Location ... 18
WIRING DIAGRAM ................................................ ... 19
Schematic ............................................................ ... 19
Wiring Diagram — ICC — ................................... ... 20
TERMINALS AND REFERENCE VALUE .............. ... 27
Terminals and Reference Value for ICC Unit ....... ... 27
Terminals and Reference Value for ICC Sensor .. ... 28
TROUBLE DIAGNOSIS — GENERAL DESCRIP-
TION ....................................................................... ... 29
Work Flow ............................................................ ... 29
CONSULT-II Function .......................................... ... 30
DESCRIPTION ................................................. ... 30
CONSULT-II BASIC OPERATION .................... ... 30
WORK SUPPORT ............................................ ... 31
SELF-DIAGNOSTIC RESULTS ........................ ... 32
DATA MONITOR .............................................. ... 32
ACTIVE TEST .................................................. ... 34
Self-Diagnostic Function ...................................... ... 36
WITH CONSULT-II ........................................... ... 36
WITHOUT CONSULT-II .................................... ... 36
SELF-DIAGNOSIS BY ICC SYSTEM DISPLAY
WILL NOT RUN ................................................ ... 38
TROUBLE DIAGNOSIS FOR SELF-DIAGNOSTIC
ITEMS ..................................................................... ... 41
Diagnostic Trouble Code (DTC) Chart ................ ... 41
DTC 11 CONTROL UNIT .................................... ... 42
DTC 20 CAN COMM CIRCUIT ............................ ... 43
DTC 31 POWER SUPPLY CIR, DTC 34 POWER
SUPPLY CIR 2 .................................................... ... 43
DTC 41 VHCL SPEED SE CIRC ......................... ... 44
DTC 43 ABS/TCS/VDC CIRC ............................. ... 45
DTC 45 BRAKE SW/STOP L SW ........................ ... 45
DTC 46 OPERATION SW CIRC .......................... ... 47
DTC 61 PRESS SEN CIRCUIT ........................... ... 48
DTC 62 BOOSTER SOL/V CIRCUIT .................. ... 50
DTC 63 RELEASE SW CIRCUIT ........................ ... 51

ACS-4
[ICC]
PRECAUTIONS
Revision: 2005 July 2005 FX
[ICC]PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
AKS00FCX
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for ICC System ServiceAKS00C88

Do not look straight into the laser beam discharger when adjusting laser beam aiming.

Turn the MAIN switch OFF in conditions similar to driving, such like Free rollers or a chassis dynamome-
ter.

Do not use the ICC sensor removing from vehicle, disassemble, or remodel the sensor.

Erase DTC when replacing parts of ICC system, then check the operation of ICC system after adjusting
laser beam aiming if necessary.

PREPARATION ACS-5
[ICC]
C
D E
F
G H
I
J
L
M A
B
ACS
Revision: 2005 July 2005 FX
PREPARATIONPFP:00002
Special Service ToolsAKS00C8A
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent - Moore No.)
Tool name Description
KV99110100
(J-45718)
ICC target board Laser beam aiming adjustment
PKIA0358J

AT-1
AUTOMATIC TRANSMISSION
C TRANSMISSION/TRANSAXLE
CONTENTS
D E
F
G H
I
J
K L
M
SECTION AT
A
B
AT
Revision: 2005 July 2005 FX
AUTOMATIC TRANSMISSION
INDEX FOR DTC ........................................................ 5
Alphabetical Index ............................................... ..... 5
DTC No. Index .................................................... ..... 6
PRECAUTIONS ..................................................... ..... 7
Precautions for Supplemental Restraint System
(SRS) “AIR BAG” and “SEAT BELT PRE-TEN-
SIONER” ............................................................. ..... 7
Precautions for On Board Diagnostic (OBD) System
of A/T and Engine ............................................... ..... 7
Precautions ......................................................... ..... 8
Service Notice or Precautions ............................. ..... 9
PREPARATION ...................................................... ... 10
Special Service Tools .......................................... ... 10
Commercial Service Tools ................................... .... 11
A/T FLUID .............................................................. ... 12
Changing A/T Fluid ............................................. ... 12
Checking A/T Fluid .............................................. ... 13
A/T Fluid Cooler Cleaning ................................... ... 15
A/T CONTROL SYSTEM ....................................... ... 18
Cross-Sectional View (2WD Models) .................. ... 18
Cross-Sectional View (AWD Models) .................. ... 19
Shift Mechanism .................................................. ... 20
TCM Function ...................................................... ... 31
CAN Communication ........................................... ... 32
Input/Output Signal of TCM ................................. ... 32
Line Pressure Control ......................................... ... 33
Shift Control ........................................................ ... 34
Lock-up Control ................................................... ... 35
Engine Brake Control .......................................... ... 36
Control Valve ....................................................... ... 37
ON BOARD DIAGNOSTIC (OBD) SYSTEM ......... ... 39
Introduction ......................................................... ... 39
OBD-II Function for A/T System .......................... ... 39
One or Two Trip Detection Logic of OBD-II ......... ... 39
OBD-II Diagnostic Trouble Code (DTC) .............. ... 39
Malfunction Indicator Lamp (MIL) ........................ ... 42
TROUBLE DIAGNOSIS ......................................... ... 43
DTC Inspection Priority Chart ............................. ... 43
Fail-safe .............................................................. ... 43
How to Perform Trouble Diagnosis for Quick and Accurate Repair ...................................................
... 45
A/T Electrical Parts Location ............................... ... 50
Circuit Diagram .................................................... ... 51
Inspections Before Trouble Diagnosis ................. ... 52
Check Before Engine Is Started .......................... ... 56
Check at Idle ........................................................ ... 57
Cruise Test - Part 1 .............................................. ... 58
Cruise Test - Part 2 .............................................. ... 60
Cruise Test - Part 3 .............................................. ... 61
Vehicle Speed at Which Gear Shifting Occurs .... ... 62
Vehicle Speed at Which Lock-up Occurs/Releases ... 63
Symptom Chart .................................................... ... 64
TCM Input/Output Signal Reference Values ........ ... 89
CONSULT-II Function (A/T) ................................. ... 90
Diagnostic Procedure without CONSULT-II ......... .103
DTC U1000 CAN COMMUNICATION LINE ........... .106
Description ........................................................... .106
On Board Diagnosis Logic ................................... .106
Possible Cause .................................................... .106
DTC Confirmation Procedure .............................. .106
Wiring Diagram — AT — CAN ............................. .107
Diagnostic Procedure .......................................... .108
DTC P0615 START SIGNAL CIRCUIT .................. .109
Description ........................................................... .109
CONSULT-II Reference Value ............................. .109
On Board Diagnosis Logic ................................... .109
Possible Cause .................................................... .109
DTC Confirmation Procedure .............................. .109
Wiring Diagram — AT — STSIG ......................... .110
Diagnostic Procedure .......................................... ..111
DTC P0700 TCM .................................................... .113
Description ........................................................... .113
On Board Diagnosis Logic ................................... .113
Possible Cause .................................................... .113
DTC Confirmation Procedure .............................. .113
Diagnostic Procedure .......................................... .113
DTC P0705 PARK/NEUTRAL POSITION SWITCH .114
Description ........................................................... .114
CONSULT-II Reference Value ............................. .114
On Board Diagnosis Logic ................................... .114

AT-4Revision: 2005 July 2005 FX
In “N” Position, Vehicle Moves .............................
.196
Large Shock (“N” to “D” Position) ........................ .197
Vehicle Does Not Creep Backward in “R” Position .200
Vehicle Does Not Creep Forward in “D” Position . .203
Vehicle Cannot Be Started from D
1 ..................... .205
A/T Does Not Shift: D
1 → D2 ............................... .208
A/T Does Not Shift: D
2 → D3 ............................... .210
A/T Does Not Shift: D
3 → D4 ............................... .212
A/T Does Not Shift: D
4 → D5 ............................... .215
A/T Does Not Perform Lock-up ........................... .217
A/T Does Not Hold Lock-up Condition ................. .219
Lock-up Is Not Released ..................................... .221
Engine Speed Does Not Return to Idle ............... .221
Cannot Be Changed to Manual Mode ................. .223
A/T Does Not Shift: 5th Gear → 4th Gear ........... .223
A/T Does Not Shift: 4th Gear → 3rd Gear ........... .225
A/T Does Not Shift: 3rd Gear → 2nd Gear .......... .227
A/T Does Not Shift: 2nd Gear → 1st Gear ........... .229
Vehicle Does Not Decelerate by Engine Brake ... .231
SHIFT CONTROL SYSTEM ................................... .233
Control Device Removal and Installation ............. .233
Control Rod Removal and Installation ................. .234
Adjustment of A/T Position .................................. .235
Checking of A/T Position ..................................... .235
A/T SHIFT LOCK SYSTEM .................................... .236
Description ........................................................... .236
Shift Lock System Electrical Parts Location ........ .236
Wiring Diagram — AT — SHIFT .......................... .237
Diagnostic Procedure .......................................... .238
KEY INTERLOCK CABLE ..................................... .240
Components ........................................................ .240
Removal and Installation ..................................... .241
ON-VEHICLE SERVICE ......................................... .243
Control Valve with TCM and A/T Fluid Temperature
Sensor 2 .............................................................. .243
Parking Components (2WD Models Only) ........... .255
Rear Oil Seal ....................................................... .262
Revolution Sensor Components (2WD Models Only) ....................................................................
.263
AIR BREATHER HOSE .......................................... .268
Removal and Installation ...................................... .268
TRANSMISSION ASSEMBLY ................................ .270
Removal and Installation (2WD Models) .............. .270
Removal and Installation (AWD Models) ............. .273
OVERHAUL ............................................................ .278
Components ......................................................... .278
Oil Channel .......................................................... .286
Locations of Adjusting Shims, Needle Bearings,
Thrust Washers and Snap Rings ......................... .288
DISASSEMBLY ...................................................... .290
Disassembly ......................................................... .290
REPAIR FOR COMPONENT PARTS ..................... .308
Oil Pump .............................................................. .308
Front Sun Gear, 3rd One-way Clutch ................... .311
Front Carrier, Input Clutch, Rear Internal Gear .... .313
Mid Sun Gear, Rear Sun Gear, High and Low
Reverse Clutch Hub ............................................. .318
High and Low Reverse Clutch ............................. .323
Direct Clutch ........................................................ .326
ASSEMBLY ............................................................ .328
Assembly (1) ........................................................ .328
Adjustment ........................................................... .341
Assembly (2) ........................................................ .344
SERVICE DATA AND SPECIFICATIONS (SDS) ... .351
General Specifications ......................................... .351
Vehicle Speed at Which Gear Shifting Occurs ..... .351
Vehicle Speed at Which Lock-up Occurs/Releases .352
Stall Speed ........................................................... .352
Line Pressure ....................................................... .352
A/T Fluid Temperature Sensor ............................. .352
Turbine Revolution Sensor ................................... .353
Vehicle Speed Sensor A/T (Revolution Sensor) .. .353
Reverse Brake ..................................................... .353
Total End Play ...................................................... .353

PRECAUTIONS AT-7
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
PRECAUTIONSPFP:00001
Precautions for Supplemental Restraint System (SRS) “AIR BAG” and “SEAT
BELT PRE-TENSIONER”
ACS002L3
The Supplemental Restraint System such as “AIR BAG” and “SEAT BELT PRE-TENSIONER”, used along
with a front seat belt, helps to reduce the risk or severity of injury to the driver and front passenger for certain
types of collision. This system includes seat belt switch inputs and dual stage front air bag modules. The SRS
system uses the seat belt switches to determine the front air bag deployment, and may only deploy one front
air bag, depending on the severity of a collision and whether the front occupants are belted or unbelted.
Information necessary to service the system safely is included in the SRS and SB section of this Service Man-
ual.
WARNING:

To avoid rendering the SRS inoperative, which could increase the risk of personal injury or death
in the event of a collision which would result in air bag inflation, all maintenance must be per-
formed by an authorized NISSAN/INFINITI dealer.

Improper maintenance, including incorrect removal and installation of the SRS, can lead to per-
sonal injury caused by unintentional activation of the system. For removal of Spiral Cable and Air
Bag Module, see the SRS section.

Do not use electrical test equipment on any circuit related to the SRS unless instructed to in this
Service Manual. SRS wiring harnesses can be identified by yellow and/or orange harnesses or
harness connectors.
Precautions for On Board Diagnostic (OBD) System of A/T and EngineACS002L5
The ECM has an on board diagnostic system. It will light up the malfunction indicator lamp (MIL) to warn the
driver of a malfunction causing emission deterioration.
CAUTION:

Be sure to turn the ignition switch OFF and disconnect the battery cable from the negative termi-
nal before any repair or inspection work. The open/short circuit of related switches, sensors, sole-
noid valves, etc. Will cause the MIL to light up.

Be sure to connect and lock the connectors securely after work. A loose (unlocked) connector will
cause the MIL to light up due to an open circuit. (Be sure the connector is free from water, grease,
dirt, bent terminals, etc.)

Be sure to route and secure the harnesses properly after work. Interference of the harness with a
bracket, etc. May cause the MIL to light up due to a short circuit.

Be sure to connect rubber tubes properly after work. A misconnected or disconnected rubber tube
may cause the MIL to light up due to a malfunction of the EGR system or fuel injection system, etc.

Be sure to erase the unnecessary malfunction information (repairs completed) from the TCM and
ECM before returning the vehicle to the customer.

AT-8
PRECAUTIONS
Revision: 2005 July 2005 FX
Precautions ACS002L6

Before connecting or disconnecting the A/T assembly har-
ness connector, turn ignition switch OFF and disconnect
the battery cable from the negative terminal. Because bat-
tery voltage is applied to TCM even if ignition switch is
turned OFF.

After performing each TROUBLE DIAGNOSIS, perform
“DTC (Diagnostic Trouble Code) Confirmation Procedure”.
If the repair is completed the DTC should not be displayed
in the “DTC Confirmation Procedure”.

Always use the specified brand of ATF. Refer to MA-12, "Fluids and Lubricants" .

Use lint-free paper not cloth rags during work.

After replacing the ATF, dispose of the waste oil using the methods prescribed by law, ordinance, etc.

Before proceeding with disassembly, thoroughly clean the outside of the transmission. It is important to
prevent the internal parts from becoming contaminated by dirt or other foreign matter.

Disassembly should be done in a clean work area.

Use lint-free paper or towels for wiping parts clean. Common shop rags can leave fibers that could inter-
fere with the operation of the transmission.

Place disassembled parts in order for easier and proper assembly.

All parts should be carefully cleansed with a general purpose, non-flammable solvent before inspection or
reassembly.

Gaskets, seals and O-rings should be replaced any time the transmission is disassembled.

It is very important to perform functional tests whenever they are indicated.

The valve body contains precision parts and requires extreme care when parts are removed and serviced.
Place disassembled valve body parts in order for easier and proper assembly. Care will also prevent
springs and small parts from becoming scattered or lost.

Properly installed valves, sleeves, plugs, etc. will slide along bores in valve body under their own weight.

Before assembly, apply a coat of recommended ATF to all parts. Apply petroleum jelly to protect O-rings
and seals, or hold bearings and washers in place during assembly. Do not use grease.

Extreme care should be taken to avoid damage to O-rings, seals and gaskets when assembling.

After overhaul, refill the transmission with new ATF.

When the A/T drain plug is removed, only some of the ATF is drained. Old ATF will remain in torque con-
verter and ATF cooling system.
Always follow the procedures under “Changing A/T Fluid” in the AT section when changing A/T fluid. Refer
to AT- 1 2 , "
Changing A/T Fluid" , AT- 1 3 , "Checking A/T Fluid" .
SEF289H
SEF217U

PRECAUTIONS AT-9
D E
F
G H
I
J
K L
M A
B
AT
Revision: 2005 July 2005 FX
Service Notice or PrecautionsACS002L7
ATF COOLER SERVICE
If ATF contains frictional material (clutches, bands, etc.), or if an A/T is repaired, overhauled, or replaced,
inspect and clean the A/T fluid cooler mounted in the radiator or replace the radiator. Flush cooler lines using
cleaning solvent and compressed air after repair. For A/T fluid cooler cleaning procedure, refer to AT- 1 5 , "
A/T
Fluid Cooler Cleaning" . For radiator replacement, refer to CO-14, "RADIATOR" (for VQ35DE), CO-41, "RADI-
AT O R" (for VK45DE).
OBD-II SELF-DIAGNOSIS

A/T self-diagnosis is performed by the TCM in combination with the ECM. The results can be read through
the blinking pattern of the A/T CHECK indicator or the malfunction indicator lamp (MIL). Refer to the table
on AT- 9 3 , "
SELF-DIAGNOSTIC RESULT MODE" for the indicator used to display each self-diagnostic
result.

The self-diagnostic results indicated by the MIL are automatically stored in both the ECM and TCM mem-
ories.
Always perform the procedure on AT- 4 0 , "
HOW TO ERASE DTC" to complete the repair and avoid
unnecessary blinking of the MIL.
For details of OBD-II, refer to EC-54, "
ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VQ35DE) or EC-745,
"ON BOARD DIAGNOSTIC (OBD) SYSTEM" (for VK45DE).

Certain systems and components, especially those related to OBD, may use the new style slide-
locking type harness connector. For description and how to disconnect, refer to PG-74, "
HAR-
NESS CONNECTOR" .

AT-10
PREPARATION
Revision: 2005 July 2005 FX
PREPARATIONPFP:00002
Special Service ToolsACS002L9
The actual shapes of Kent-Moore tools may differ from those of special service tools illustrated here.
Tool number
(Kent-Moore No.)
Tool name Description
ST2505S001
(J-34301-C)
Oil pressure gauge set
1. ST25051001
(—)
Oil pressure gauge
2. ST25052000
(—)
Hose
3. ST25053000
(—)
Joint pipe
4. ST25054000
(—)
Adapter
5. ST25055000
(—)
Adapter Measuring line pressure
KV31103600
(J-45674)
Joint pipe adapter
(With ST25054000) Measuring line pressure
ST33400001
(J-26082)
Drift
a: 60 mm (2.36 in) dia.
b: 47 mm (1.85 in) dia.

Installing rear oil seal (2WD models)

Installing oil pump housing oil seal
KV31102400
(J-34285 and J-34285-87)
Clutch spring compressor
a: 320 mm (12.60 in)
b: 174 mm (6.85 in) Installing reverse brake return spring retainer
ST25850000
(J-25721-A)
Sliding hammer
a: 179 mm (7.05 in)
b: 70 mm (2.76 in)
c: 40 mm (1.57 in)
d: M12X1.75P Removing oil pump assembly
SCIA3695J
ZZA1227D
NT086
NT423
NT422