warning INFINITI M 2011 Repair Manual

WARNING
In freezing temperatures the washer solution
may freeze on the windshield and obscure your
vision which may lead to an accident. Warm
windshield with the defroster before you wash
the windshield.
CAUTION
●Do not operate the washer continuously for
more than 30 seconds.
● Do not operate the washer if the reservoir
tank is empty.
● Do not fill the window washer reservoir tank
with washer fluid concentrates at full
strength. Some methyl alcohol based
washer fluid concentrates may permanently
stain the grille if spilled while filling the win-
dow washer reservoir tank.
● Pre-mix washer fluid concentrates with wa-
ter to the manufacturer’s recommended lev-
els before pouring the fluid into the window
washer reservoir tank. Do not use the win-
dow washer reservoir tank to mix the washer
fluid concentrate and water. The windshield wiper and washer operates
when the ignition switch is in the ON position.
Push the lever down to operate the wiper at the
following speed:
1AUTO — operates the rain-sensing auto
wiper system. (See “RAIN-SENSING AUTO
WIPER SYSTEM” later in this section.)
2LO — continuous low speed operation
3HI — continuous high speed operation
4MIST — one sweep operation of the wiper
Pull the lever toward you
5to operate the
washer. Then the wiper will also operate several
times. Pulling up the wiper arm:
The wiper arm should be in the up position
when replacing the wiper.
To pull up the wiper arm, push up
4twice, the
wiper operation stops in mid-operation. The
wiper arm can be pulled up.
The selector lever should be in the P (Park)
position.
To replace the wiper arm, place the wiper arm in
the down position and then push the lever
4
up once.
CAUTION
Do not operate the windshield wiper while the
wiper arm is pulled up. The wiper arm may be
damaged.
Wiper drip wipe system:
The wiper will also operate once about 3 sec-
onds after the washer and wiper are operated.
This operation is to wipe washer fluid that has
dripped on the windshield.
SIC4281
WINDSHIELD WIPER AND WASHER SWITCH
2-30Instruments and controls
—
—
07/15/10—tbrooks


To defog/defrost the rear window glass and
outside mirrors, start the engine and push the
switch
1on. The indicator light2will come
on. Push the switch again to turn the defroster
off.
It will automatically turn off in approximately 30
minutes.
CAUTION
When cleaning the inner side of the rear win-
dow, be careful not to scratch or damage the
rear window defroster.
XENON HEADLIGHTS
WARNING
HIGH VOLTAGE
● When xenon headlights are on, they produce
a high voltage. To prevent an electric shock,
never attempt to modify or disassemble.
Always have your xenon headlights replaced
at an INFINITI retailer.
● Xenon headlights provide considerably more
light than conventional headlights. If they
are not correctly aimed, they might
temporarily blind an oncoming driver or the
driver ahead of you and cause a serious
accident. If headlights are not aimed
correctly, immediately take your vehicle to
an INFINITI retailer and have the headlights
adjusted correctly.
When the xenon headlight is initially turned on,
its brightness or color varies slightly. However,
the color and brightness will soon stabilize. ●
The life of xenon headlights will be shortened
by frequent on-off operation. It is generally
desirable not to turn off the headlights for
short intervals (for example, when the ve-
hicle stops at a traffic signal). Even when the
daytime running lights are active (Canada
only), the xenon headlights do not turn on.
This way the life of the xenon headlights is
not reduced.
● If the xenon headlight bulb is close to burn-
ing out, the brightness will drastically de-
crease, the light will start blinking, or the
color of the light will become reddish. If one
or more of the above signs appear, contact an
INFINITI retailer.
SIC4330
REAR WINDOW AND OUTSIDE MIRROR
DEFROSTER SWITCH HEADLIGHT AND TURN SIGNAL SWITCH
2-32Instruments and controls
—
—
07/15/10—tbrooks


TURN SIGNAL SWITCH
1Turn signal
Move the lever up or down to signal the turning
direction. When the turn is completed, the turn
signals cancel automatically.
2Lane change signal
To indicate a lane change, move the lever up or
down to the point where lights begin flashing.
FOG LIGHT SWITCH
To turn the fog lights on, turn the headlight
switch to the
position, then turn the
switch to the
position. To turn them off,
turn the switch to the OFF position.
The headlights must be on for the fog lights to
operate.
When the headlight switch is in the AUTO
position, turning the fog light switch to the
position will turn on the headlights, fog
lights and the other lights while the ignition
switch is in the ON position or the engine is
running. Push the switch on to warn other drivers when
you must stop or park under emergency condi-
tions. All turn signal lights will flash.
WARNING
●
If stopping for an emergency, be sure to
move the vehicle well off the road.
● Do not use the hazard warning flashers while
moving on the highway unless unusual cir-
cumstances force you to drive so slowly that
your vehicle might become a hazard to other
traffic.
● Turn signals do not work when the hazard
warning flasher lights are on.
SIC3271SIC3272SIC2574
HAZARD WARNING FLASHER SWITCH
Instruments and controls2-37
—
—
07/15/10—tbrooks


The flasher can be actuated with the ignition
switch in any position.
When an impact that could activate the supple-
mental air bags is detected, the hazard warning
flasher lights blink automatically. If the hazard
warning flasher switch is pushed, the hazard
warning flashers will turn off.
WARNING
Do not turn the hazard warning flasher switch
to off until you can make sure that it is safe to
do so. Also, the hazard flasher warning may not
blink automatically depending on the force of
impact.
Some state laws may prohibit the use of the
hazard warning flasher switch while driving. The heated steering wheel system is designed
to operate only when the surface temperature of
the steering wheel is below 68°F (20°C).
Push the heated steering wheel switch to warm
the steering wheel after the engine starts. The
indicator light
1on the switch will illuminate.
If the surface temperature of the steering wheel
is below 68°F (20°C), the system will heat the
steering wheel and cycle off and on to maintain
a temperature above 68°F (20°C). The indicator
light will remain on as long as the system is on.
Push the switch again to turn the heated steer-
ing wheel system off manually. The indicator
light will turn off. NOTE:
If the surface temperature of the steering wheel
is above 68°F (20°C) when the switch is turned
on, the system will not heat the steering wheel.
This is not a malfunction.
SIC4401
HEATED STEERING WHEEL (if so equipped)
2-38Instruments and controls
—
—
07/15/10—tbrooks


To sound the horn, push the center pad area of
the steering wheel.
WARNING
Do not disassemble the horn. Doing so could
affect proper operation of the supplemental
front air bag system. Tampering with the
supplemental front air bag system may result
in serious personal injury.
WARNING
Do not use or allow occupants to use the seat
heater if you or the occupants cannot monitor
elevated seat temperatures or have an inability
to feel pain in body parts that contact the seat.
Use of the seat heater by such people could
result in serious injury.
CAUTION
●The battery could run down if the seat heater
is operated while the engine is not running.
● Do not use the seat heater for extended pe-
riods or when no one is using the seat.
● Do not put anything on the seat which insu-
lates heat, such as a blanket, cushion, seat
cover, etc. Otherwise, the seat may become
overheated.
● Do not place anything hard or heavy on the
seat or pierce it with a pin or similar object.
This may result in damage to the heater.
● Any liquid spilled on the heated seat should
be removed immediately with a dry cloth.
● When cleaning the seat, never use gasoline,
thinner, or any similar materials. ●
If any abnormalities are found or the heated
seat does not operate, turn the switch off
and have the system checked by an INFINITI
retailer.SIC4332
HORN HEATED SEATS (if so equipped)
Instruments and controls2-39
—
—
07/15/10—tbrooks


4. When the vehicle’s interior is warmed orcooled, and/or before you leave the ve-
hicle, be sure to turn the control knob to
the OFF position (center). The indicator
light
Bon the control knob goes off at
the OFF position.
To check the air filter for the climate con-
trolled seat, contact an INFINITI retailer.
WARNING
Do not use or allow occupants to use the seat
heater if you or the occupants cannot monitor
elevated seat temperatures or have an inability
to feel pain in body parts that contact the seat.
Use of the seat heater by such people could
result in serious injury.
CAUTION
● The battery could run down if the climate
controlled seat is operated while the engine
is not running.
● Do not use the climate controlled seat for
extended periods or when no one is using
the seat. ●
Do not put anything on the seat which insu-
lates heat, such as a blanket, cushion, seat
cover, etc. Otherwise, the seat may become
overheated.
● Do not place anything hard or heavy on the
seat or pierce it with a pin or similar object.
This may result in damage to the climate
controlled seat.
● Any liquid spilled on the seat should be re-
moved immediately with a dry cloth.
● The climate controlled seat has an air filter.
Do not operate climate controlled seat with-
out an air filter. This may result in damage to
the system.
● When cleaning the seat, never use gasoline,
thinner, or any similar materials.
● If any malfunctions are found or the climate
controlled seat does not operate, turn the
switch off and have the system checked by
an INFINITI retailer. The warning systems switch will turn on and off
the Lane Departure Warning (LDW) system, the
Blind Spot Warning (BSW) system and the For-
ward Collision Warning (FCW) system at the
same time.
The FCW system will sound a warning chime
and the vehicle ahead detection indicator light
blinks to alert the driver if the vehicle is travel-
ing close to the vehicle ahead. (See “FORWARD
COLLISION WARNING (FCW) SYSTEM” in the “5.
Starting and driving” section.)
The LDW system will sound a warning chime
and blink the lane departure warning light
(orange) to alert the driver if the vehicle is
traveling close to either the left or the right of a
SIC4335
WARNING SYSTEMS SWITCH (if so
equipped)
Instruments and controls2-41
—
—
07/15/10—tbrooks


traveling lane with detectable lane markers.
(See “LANE DEPARTURE WARNING (LDW)
SYSTEM/LANE DEPARTURE PREVENTION (LDP)
SYSTEM” in the “5. Starting and driving” sec-
tion.)
The Blind Spot Warning (BSW)/Blind Spot Inter-
vention (BSI) indicator lights, located next to
the outside mirrors, will illuminate if the radar
sensors detect a vehicle in the detection zone. If
the turn signal is activated in the direction of
the detected vehicle, a chime sounds twice and
the BSW/BSI indicator light will flash. (See
“BLIND SPOT WARNING (BSW) SYSTEM/BLIND
SPOT INTERVENTION™ (BSI) SYSTEM” in the “5.
Starting and driving” section.)
The warning systems switch is automatically
turned on when the engine is started, and the
warning systems ON indicator
1on the switch
illuminates.
To cancel the warning systems, push the warn-
ing systems switch to turn off the system. The
warning systems ON indicator will turn off. NOTE:
If you continue to push the warning systems
switch from off to on for over 4 seconds, a chime
will sound. This will change the default status of
the LDW, BSW and FCW systems to OFF so that
these systems will not automatically turn on
when the engine is started. If this procedure is
repeated, the default status will return to ON.
The vehicle should be driven with the Intelligent
Brake Assist (IBA) system on for most driving
conditions.
The Intelligent Brake Assist (IBA) system will
sound a warning chime and the vehicle ahead
detection indicator light blinks to alert the
driver when the vehicle is traveling too close to
the vehicle ahead. The system will also apply
the brake control if necessary.
To turn off the system, push the IBA OFF switch.
The
indicator will illuminate.
The IBA system will remain in the last ON or OFF
state it was left in until it is manually changed
by pushing the IBA OFF switch.
SIC4337
INTELLIGENT BRAKE ASSIST (IBA) OFF
SWITCH (if so equipped)
2-42Instruments and controls
—
—
07/15/10—tbrooks


To open the cup holder, push the lid1.
To remove the inner tray for cleaning, pull it up
as illustrated
2. Open the lid of the rear center armrest to use
the cup holder.
SUNGLASSES HOLDER
WARNING
Keep the sunglasses holder closed while driv-
ing to prevent an accident.
To open the sunglasses holder, push
1.
CAUTION
● Do not use for anything other than glasses.
● Do not leave glasses in the sunglasses
holder while parking in direct sunlight. The
heat may damage the glasses.
Front
SIC4342
Rear
SIC2875SIC4344
2-46Instruments and controls
—
—
07/15/10—tbrooks


GLOVE BOX
WARNING
Keep glove box lid closed while driving to help
prevent injury in an accident or a sudden stop.
To open the glove box, pull the handle
1.
To close, push the lid in until the lock latches.
To lock
2/unlock3the glove box, use the
mechanical key. For the mechanical key usage,
see “KEYS” in the “3. Pre-driving checks and
adjustments” section.
CONSOLE BOX
To open the console box, push up the knobA
and pull up the lid.
To close, push the lid down until latched.
SIC4345SIC4346
Type A
SIC3929
Type B
SIC4348
Instruments and controls2-47
—
—
07/15/10—tbrooks


TRUNK HOOKS
WARNING
●Always make sure that the cargo is properly
secured. Use the suitable ropes and hooks.
● Unsecured cargo can become dangerous in
an accident or sudden stop.
CAUTION
Do not apply a total load of more than 22 lb (10
kg) to a single hook.
POWER WINDOWS
WARNING
● Make sure that all passengers have their
hands, etc. inside the vehicle while it is in
motion and before closing the windows. Use
the window lock switch to prevent unex-
pected use of the power windows.
● Do not leave children unattended inside the
vehicle. They could unknowingly activate
switches or controls and become trapped in
the window. Unattended children could be-
come involved in serious accidents.
The power windows operate when the ignition
switch is in the ON position or for about 45
seconds after the ignition switch is pushed to
the OFF position. If the driver’s or front passen-
ger’s door is opened during this period of about
45 seconds, power to the windows is canceled.
Main power window switch (driver’s
side)
1. Driver side window
2. Front passenger side window
3. Rear left passenger side window
4. Rear right passenger side window
5. Window lock button
To open or close the window, push downAor
pull up
Bthe switch and hold it. The main
switch (driver side switches) will open or close
all the windows.
SIC4350SIC4352
WINDOWS
Instruments and controls2-49
—
—
07/15/10—tbrooks